Semi-batch control

Using a batch reactor, a constant concentration of sulfuric acid can be maintained by adding concentrated sulfuric acid as the reaction progresses, i.e., semi-batch operation. Good temperature control of such systems can be maintained, as we shall discuss later. 

A semi-batch reactor has the same disadvantages as the batch reactor. However, it has the advantages of good temperature control and the capability of minimizing unwanted side reactions by maintaining a low concentration of one of the reactants. Semi-batch reactors are also of value when parallel reactions of different orders occur, where it may be more profitable to use semi-batch rather than batch operations. In many applications semi-batch reactors involve a substantial increase in the volume of reaction mixture during a processing cycle (i.e., emulsion polymerization). 

The product crystals were agglomerates of needles or dendrites. Loose floes of dendroid strontium carbonate are compacted by agitation, which is an important factor in controlling the habit of product particles. Semi-batch operation produces larger particles compared to batch or continuous operation. 

With semi-continuous (more properly, semi-batch) reactors only part of the charge is added at the beginning of the cycle. Usually some reaction time is allowed to pass before the remaining part of the charge is added in a controlled manner. Sometimes... 

Application of Time to Temperature Control of Semi-Batch Reactors... 

Temperature control of a large, highly exothermic semi-batch chemical or polymer reactor can be an involved problem. The reaction may be auto-acceleratlng. Heat transfer rates can vary during the process. Random disturbances can enter the process from many sources. Changes In... 

One final note While the techniques used here were applied to control temperature In large, semi-batch polymerization reactors, they are by no means limited to such processes. The Ideas employed here --designing pilot plant control trials to be scalable, calculating transfer functions by time series analysis, and determining the stochastic control algorithm appropriate to the process -- can be applied In a variety of chemical and polymerization process applications. 

The pyrolysis of the plastics was carried out in a semi-batch reactor which was made of cylindrical stainless steel tube with 80mm in internal diameter and 135mm in height. A schematic diagram of the experimental apparatus is shown in Fig. 1, which includes the main reactor, temperature controller, agitator, condenser and analyzers. 

Generally, the temperature changes with time or, equivalently, with distance from the reactor inlet (for flow reactors). This change is usually controlled well in reaction calorimeters but can become uncontrolled in other conventional laboratory flow or (semi)batch reactors. The balance equations of a batch reactor for a single reaction of a-th order kinetics are given by ... 

SEMIEX - Temperature Control for Semi-Batch Reactor... 

Figure 5.166. Exothermic semi-batch reactor with feed control.

Semi-batch reactor with heat production Feedback control of feed stream Jacket cooling... 

Chemical Kinetics, Tank and Tubular Reactor Fundamentals, Residence Time Distributions, Multiphase Reaction Systems, Basic Reactor Types, Batch Reactor Dynamics, Semi-batch Reactors, Control and Stability of Nonisotheimal Reactors. Complex Reactions with Feeding Strategies, Liquid Phase Tubular Reactors, Gas Phase Tubular Reactors, Axial Dispersion, Unsteady State Tubular Reactor Models... 

The depolymerized Nylon used in the hydrogenation process was obtained by the ammonolysis of a mixture of Nylon-6 and Nylon-6,6 (described elsewhere, see reference 2). Hydrogenation reactions were conducted in 300 cc stirred pressure vessels. For semi-batch reactions hydrogen was constantly replenished to the reactor from a 1L reservoir to maintain a reactor pressure of 500 psig and all of the reactions were conducted with the same operating parameters and protocol. In continuous stirred tank studies hydrogen flow was controlled using... 

Polymer production technology involves a diversity of products produced from even a single monomer. Polymerizations are carried out in a variety of reactor types batch, semi-batch and continuous flow stirred tank or tubular reactors. However, very few commercial or fundamental polymer or latex properties can be measured on-line. Therefore, if one aims to develop and apply control strategies to achieve desired polymer (or latex) property trajectories under such a variety of conditions, it is important to have a valid mechanistic model capable of predicting at least the major effects of the process variables. 

A batch reactor is an agitated vessel in which the reactants are precharged and which is then emptied after the reaction is completed. More frequently for exothermic reactions, only part of the reactants are charged initially, and the remaining reactants and catalysts are fed on a controlled basis this is called a semi-batch operation. For highly exothermic reactions and for two-phase (gas-liquid) reactions, loop reactors with resultant smaller volumes can be used. 

It should be noted that there are cases in which some selectivity will be lost in choosing a semi-batch mode over a simple batch reactor. If the desired product decomposes by a consecutive reaction, the yield will be higher in the batch reactor [177]. If, on the other hand, the reactants are producing by-products by a parallel reaction, the semi-batch process will give the higher yield. In any case, if the heat production rate per unit mass is very high, the reaction can then be run safely under control only in a semi-batch reactor. 

A process is described [224] in which an exothermic reaction takes place in a semi-batch reactor at elevated temperatures and under pressure. The solid and liquid raw materials are both toxic and flammable. Spontaneous ignition is possible when the reaction mass is exposed to air. Therefore, the system must be totally enclosed and confined in order to contain safely any emissions arising from the loss of reactor control, and to prevent secondary combustion reactions upon discharge of the materials to the atmosphere. Further, procedures and equipment are necessary for the safe collection and disposal of solid, liquid, and gaseous emission products. 

The process is run in a semi-batch mode, and multiple reactors are used. There are several possible causes for a loss of control such as insufficient heat removal and loss of agitation. Overpressurization leading to the bursting of rupture discs takes place several times per year, indicating both the clear need for containment but also a need to consider design and control improvements. The reference describes the autoclave rupture disc assembly, procedures for replacement of the discs, the cleaning of the containment vessels, and the routine maintenance procedures for the containment vessels. 

Semi-Batch Reactor (SBR) a type of batch reactor from which at least one reactant is withheld and then added at a controlled rate, usually to control the rate of heat generation or gas evolution both heat generation and concentrations vary during the reaction process products are removed from the reactor only upon conclusion of the reaction process. 

Temperature Control for Semi-Batch Reactor 430 Parallel Reactions in a Semi-Continuous Reactor 347 Sequential-Parallel Reactions in a Semi-Continous Reactor 350... 

---