Terpolymer rubber

The photo-oxidative degradation of two types of EPDM rubbers (terpolymer) has been investigated in detail ... 

Elastomers. Ethylene—propylene terpolymer (diene monomer) elastomers (EPDM) use a variety of third monomers during polymerization (see Elastomers, ethyiene-propylene-diene rubber). Ethyhdenenorbomene (ENB) is the most important of these monomers and requires dicyclopentadiene as a precursor. ENB is synthesized in a two step preparation, ie, a Diels-Alder reaction of CPD (via cracking of DCPD) with butadiene to yield 5-vinylbicyclo[2.2.1]-hept-2-ene [3048-64-4] (7) where the external double bond is then isomerized catalyticaHy toward the ring yielding 5-ethyhdenebicyclo[2.2.1]-hept-2-ene [16219-75-3] (ENB) (8) (60). 

A terpolymer rubber was introduced by Du Pont in 1975 (Vamac). This is based on ethylene, methyl acrylate and a third, undisclosed, monomer containing carboxylic acid groups to act as the cure site (see Section 11.9). 

More recently, in 1975, Du Pont introduced a terpolymer (Vamac) based on ethylene, methyl acrylate and a third monomer of undisclosed composition which contained a carboxylic acid group to provide a cure site for use with peroxides or amines. Both types of rubber exhibit good heat, oxygen and ozone resistance. 

Whilst polyisobutene is a non-rubbery polymer exhibiting high cold flow (see Section 11.3), the copolymer containing about 2% isoprene can be vulcanised with a powerful accelerated sulphur system to give moderately rubbery polymers. The copolymers were first developed in 1940 by Esso and are known as butyl rubbers and designated as HR. As they are almost saturated they have many properties broadly similar to the EPDM terpolymers. They do, however, have two properties that should be particularly noted ... 

The anomalous effect of the last two rubbers in the table with their low solubility parameters is possibly explained by specific interaction of PVC with carbonyl and carboxyl groups present respectively in the ketone- and fumarate-containing rubbers to give a more than expected measure of compatibility. It is important to note that variation of the monomer ratios in the copolymers and terpolymers by causing changes in the solubility parameter and eompatibility will result in variation in their effect on impact strength. 

At one time butadiene-acrylonitrile copolymers (nitrile rubbers) were the most important impact modifiers. Today they have been largely replaced by acrylonitrile-butadiene-styrene (ABS) graft terpolymers, methacrylate-buta-diene-styrene (MBS) terpolymers, chlorinated polyethylene, EVA-PVC graft polymers and some poly acrylates. 

In attempts to further improve the stability of fluorine-containing elastomers Du Pont developed a polymer with no C—H groups. This material is a terpolymer of tetrafluoroethylene, perfluoro(methyl vinyl ether) and, in small amounts, a cure site monomer of undisclosed composition. Marketed as Kalrez in 1975 the polymer withstands air oxidation up to 290-315°C and has an extremely low volume swell in a wide range of solvents, properties unmatched by any other commercial fluoroelastomer. This rubber is, however, very expensive, about 20 times the cost of the FKM rubbers and quoted at 1500/kg in 1990, and production is only of the order of 1 t.p.a. In 1992 Du Pont offered a material costing about 75% as much as Kalrez and marketed as Zalak. Structurally, it differs mainly from Kalrez in the choice of cure-site monomer. 

Whilst the ASA materials are of European origin, the AES polymers have been developed in Japan and the US. The rubber used is an ethylene-propylene terpolymer rubber of the EPDM type (see Chapter 11) which has a small amount of a diene monomer in the polymerisation recipe. The residual double bonds that exist in the polymer are important in enabling grafting with styrene and acrylonitrile. The blends are claimed to exhibit very good weathering resistance but to be otherwise similar to ABS. 

Initial materials of this super-tough type were blends of nylon 66 with an ionomer resin (see Chapter 11). More recent materials are understood to be blends of nylon 66 with a modified ethylene-propylene-diene terpolymer rubber (EPDM rubber—also see Chapter 11). One such modification involves treatment of the rubber with maleic anhydride, this reacting by a Diels—Alder or other... 

Standard butyl rubber, which is a copolymer of isobutylene with about 2% of isoprene vulcanises in the same manner as natural rubber but, as it only contains a small proportion of polyisoprene, the cross-link percentage is much reduced. It is therefore not possible to make ebonite from a butyl rubber. The same vulcanisation chemistry, with some modifications, applies to ethylene-propylene terpolymers and brominated butyl rubber. 

The simultaneous polymerization and sol-gel reaction often brings complexity to the overall reaction. Moreover, it is difficult to control the molecular weight of the sample. Recently, Patel et al. [51] have synthesized the rubber grade acrylic copolymers and terpolymers-/n situ silica hybrid nanocomposites using this technique. 

Adsorption of rubber over the nanosilica particles alters the viscoelastic responses. Analysis of dynamic mechanical properties therefore provides a direct clue of the mbber-silica interaction. Figure 3.22 shows the variation in storage modulus (log scale) and tan 8 against temperature for ACM-silica, ENR-silica, and in situ acrylic copolymer and terpolymer-silica hybrid nanocomposites. 

Patel et al. [70] in a recent publication have explored the adhesive action of the mbber-siUca hybrid nanocomposites on different substrates. The rubber-silica hybrid nanocomposites are synthesized through in situ silica formation from TEOS in strong acidic pH within acryhc copolymer (EA-BA) and terpolymer (EA-BA-AA) matrices. The transparent nanocomposites have been apphed in between the aluminum (Al), wood (W), and biaxially oriented polypropylene (PP) sheets separately and have been tested for peel strength, lap shear strength, and static holding power of the adhesive joints. 

The copolymer-silica adhesives also follow a similar trend but fail much earlier than the terpolymer-based adhesives. This is because of two factors (1) the increase in the inherent strength of the adhesive due to more favorable terpolymer rubber-silica interaction and (2) chemisorption in much higher magnitude between the polar substrates and the nanocomposites. 

The most prevalent approach to achieve long-lasting and nonstaining ozone protection of rubber compounds is to use an inherently ozone-resistant, saturated backbone polymer in blends with a diene rubber. The ozone-resistant polymer must be used in sufficient concentration (minimum 25 phr) and must also be sufficiently dispersed to form domains that effectively block the continuous propagation of an ozone-initiated crack through the diene rubber phase within the compound. Elastomers such as ethylene-propylene-diene terpolymers, halogenated butyl mbbers, or brominated isobutylene-co-para-methylstyrene elastomers have been proposed in combination with NR and/or butadiene rubber. 

Impact modifiers Polybutadiene rubber, methacrylate-butadiene-styrene terpolymers, acrylic rubber... 

SEM and transmission electron microscopy (TEM) are employed to examine materials for the presence and distribution of impact modifiers such as polybutadiene rubber in high impact polystyrene (HIPS) and methacrylate butadiene styrene terpolymer in PVC. Quantification is either by transmission IR spectroscopy against standards or nuclear magnetic resonance (NMR) spectroscopy. 

The isoprene units in the copolymer impart the ability to crosslink the product. Polystyrene is far too rigid to be used as an elastomer but styrene copolymers with 1,3-butadiene (SBR rubber) are quite flexible and rubbery. Polyethylene is a crystalline plastic while ethylene-propylene copolymers and terpolymers of ethylene, propylene and diene (e.g., dicyclopentadiene, hexa-1,4-diene, 2-ethylidenenorborn-5-ene) are elastomers (EPR and EPDM rubbers). Nitrile or NBR rubber is a copolymer of acrylonitrile and 1,3-butadiene. Vinylidene fluoride-chlorotrifluoroethylene and olefin-acrylic ester copolymers and 1,3-butadiene-styrene-vinyl pyridine terpolymer are examples of specialty elastomers. 

One component of a terpolymer of butadiene, styrene and vinyl pyridine used in latex form to promote good adhesion between rubber and textiles, particularly rayon and nylon. Viscoelasticity... 

The carboxylated types (XNBR) contain one, or more, acrylic type of acid as a terpolymer, the resultant chain being similar to nitrile except for the presence of carboxyl groups which occur about every 100 to 200 carbon atoms. This modification gives the polymer vastly improved abrasion resistance, higher hardness, higher tensile and tear strength, better low temperature brittleness, and better retention of physical properties after hot-oil and air ageing when compared to ordinary nitrile rubber. 

Since the main chain of both EPM and EPDM rubbers is saturated, both co- and terpolymers exhibit excellent stability to oxygen, UV light, and are ozone resistant. 

Acrylic rubber Chlorinated polyethylene Chlorosulphonated polyethylene Ethylene-propylene copolymer Ethylene-propylene terpolymer Fluorocarbon rubbers (certain grades)... 

---