Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Reflux procedure

Principles and Characteristics In boiling under reflux procedures a small amount of ground polymer (typically 3g) is placed in a headspace jar (typically 100 mL) and solvent (typically 30 mL) is added. After sealing, the jar is placed in an oven at a temperature where the solvent slowly refluxes. The solvent is, therefore, at the highest temperature possible without applying an external pressure. Consequently, reflux extractions tend to be much faster than Soxhlet extractions. Examples are Soxtec , Soxtherm , FEXTRA and intermittent extraction. Whilst, in theory, partitioning of the analyte between the polymer and solvent prevents complete extraction, this hardly ever constitutes a problem in practice. As the quantity of solvent is much larger than that of the polymer, and the partition coefficients usually favour the solvent, very low additive levels in the polymer result at equilibrium. Any solvent or solvent mixture can be used. [Pg.67]

The acid reflux procedure was first described by Rinzler el al. [28], in which raw nanotube materials are refluxed in nitric acid to oxidize the metals and carbon impurities. Acid-treated CNTs are considered to have carboxylic acid groups at the tube ends and, possibly, at defects on the side walls. The functionalized SWNTs have considerably different properties from those of the pristine tubes. [Pg.487]

In the reflux procedure, minor amounts of the corresponding arylhydrazines are formed as by-products. [Pg.125]

Another possible evidence of grafted organic/polymeric molecules onto CNT surface can be achieved by microscopy analyses using both principal types of electron microscopy - transition electron microscopy, TEM, or scanning electron microscopy, SEM (15,19,24,44,45,47). Such analyses are usually performed after careful extraction of the polymer from tubes by polymer solvents, performed several times by a reflux procedure with an excess of solvent therefore it is supposed that only covalently attached molecules remain fixed at CNT surface. High Resolution mode of TEM analysis shows the evidence of amorphous material on nanotubes surface (15). [Pg.233]

A selection of configurations, suitable for most reflux procedures is shown in... [Pg.120]

I, 4-cyclohexanediol, 3.3 grams (0.105 mole, if 95% pure) of paraformaldehyde, 0.05 gram of p-toluenesulfonic acid, and 40 ml. of benzene was stirred at 60° C. for 1 hour. The solution was then refluxed for 2 hours, and the water which formed was collected in a Dean-Stark trap filled with benzene. More paraformaldehyde (0.15 gram) was added, and the mixture was stirred at 60° C. for 0.5 hour before refluxing for 1 hour. Another 0.15 gram of paraformaldehyde was added, and the simmering and refluxing procedures were repeated. (These extra additions of paraformaldehyde were probably not necessary in this procedure, since solid-phase buildup was used, and only two experiments were carried out with this diol.) The benzene was then removed under reduced pressure, while the mixture was heated on the steam bath. [Pg.203]

Consistent with this, addition of acetone or cyclohexanol to the reaction mixture prior to the refluxing procedure has little effect on the hydrogenation rates in any case, much of the acetone will be in the gas headspace. A metal hydride will attack the ketone with the highest reduction potential (17), and calculations using literature E° n values for C5H10O and acetone, 162 and 129 mV, respectively... [Pg.88]

Plants of A/. chmiomiUa L. were dried and powdered. One kg of the powder was extracted in 2 liters of 95% ethanol for about 24 hours at room temperature. The solution was filtered and the Ullralc saved. Two liters of 95% ethanol were added to the residue and refluxed in a water bath for 6 hours. The refluxed ethanol was cooled and nilcrcd and the filtrate combined with the extract filtrate. Ethanol was llicn recovered by reduced pressure distillation and the residue was saved. One thousand ml of acetic cilter was added to the residue and refluxed in a water bath for 6 hours. The refluxing procedure was repeated. Acetic ether was then concentrated under reduced pressure distillation. Crystals were formed which were then washed with water. The final crystals were dried under vacuum and were found to have a melting point of about 250" C (7). [Pg.106]

As an example, a common step in organic processing is maintaining a reaction mix at a fixed temperature over a period of time by refluxing the solvent from the batch. This requires the solvent vapors to be condensed efficiently and redirected back to the batch to retain batch volume and concentration. However, if some part of the reflux procedure... [Pg.301]

Definitive treatment will be performed by gastro-pexy, which can be done laparoscopically. In some patients an anti-reflux procedure may be needed, but this is not always necessary at first (Darani et al. 2005). [Pg.115]

If larger quantities of the water precursors are used, one must use multiple batches of freshly activated sieves during the dehydration process. If water is detected in the infrared spectrum of the product, then it is necessary to redissolve the solids in dry acetonitrile and repeat the Soxhlet extraction reflux procedure. [Pg.79]

If preferred, the following alternative procedure may be adopted. The absolute alcohol is placed in a 1 5 or 2 litre three-necked flask equipped with a double surface reflux condenser and a mercury-sealed mechanical stirrqr the third neck is closed with a dry stopper. The sodium is introduced and, when it has reacted completely, the ester is added and the mixture is gently refluxed for 2 hours. The reflux condenser is then rapidly disconnected and arranged for downward distillation with the aid of a short still head or knee tube. The other experimental details are as above except that the mixture is stirred during the distillation bumping is thus reduced to a minimum. [Pg.168]

Allyl Chloride. Comparatively poor yields are obtained by the zinc chloride - hydrochloric acid method, but the following procedure, which employs cuprous chloride as a catalyst, gives a yield of over 90 per cent. Place 100 ml. of allyl alcohol (Section 111,140), 150 ml. of concentrated hydrochloric acid and 2 g. of freshly prepared cuprous chloride (Section II,50,i one tenth scale) in a 750 ml. round-bottomed flask equipped with a reflux condenser. Cool the flask in ice and add 50 ml. of concen trated sulphuric acid dropwise through the condenser with frequent shaking of the flask. A little hydrogen chloride may be evolved towards the end of the reaction. Allow the turbid liquid to stand for 30 minutes in order to complete the separation of the allyl chloride. Remove the upper layer, wash it with twice its volume of water, and dry over anhydrous calcium chloride. Distil the allyl chloride passes over at 46-47°. [Pg.276]

For water insoluble aldehydes or ketones, the following alternative procedure may be used. Reflux a mixture of 0-6 g. of the aldehyde or ketone, 0 5 g. of hydroxylamine hydrochloride, 5 ml. of ethanol and 0 5 ml. of pyridine on a water bath for 15-60 minutes. Remove the alcohol either by distillation (water bath) or by evaporation of the hot solution in a stream of air (water pump). Add 5 ml. of water to the cooled residue, cool in an ice bath and stir until the oxime crystallises Filter off the solid, wash it with a little water and dry. Recrystallise from alcohol (95 per cent, or more dilute), benzene, or benzene - light petroleum (b.p. 60-80°). [Pg.345]

Place 1 0 g. of the monobasic acid and 2 g. of aniline or p-toluidine in a dry test-tube, attach a short air condenser and heat the mixture in an oil bath at 140-160° for 2 hours do not reflux too vigorously an acid that boils below this temperature range and only allow steam to escape from the top of the condenser. For a sodium salt, use the proportions of 1 g. of salt to 1 5 g. of the base. If the acid is dibasic, employ double the quantity of amine and a reaction temperature of 180-200° incidentally, the procedure is recommended for dibasic acids since the latter frequently give anhydrides with thionyl chloride. Powder the cold reaction mixture, triturate it with 20-30 ml. of 10 per cent, hydrochloric acid, and recrystallise from dilute alcohol. [Pg.362]

Both of these methods are more economical in the consumption of alcohol and more convenient than that in which the acid is refluxed with a large excess of alcohol in the presence of concentrated sulphuric acid. An example of the latter procedure is described ... [Pg.381]

Suberic acid. Prepare hexamethylene dibromide from hexamethy-lene glycol (Section 111,15) according to the procedure described in Section 111,35). Convert the 1 6-dibromohexane, b.p. H4r-115°/12 mm., into hexamethylene dicyanide, b.p. 178-180°/15 mm., by refluxing it with a 20-25 per eent. excess of aqueous - alcoholic sodium cyanide solution (compare Section 111,114), distilling off the hquid under diminished... [Pg.491]

If preferred, the PCI, may be replaced by 4-5 ml. of POCI, and the mixture refluxed for 4 hours. The subsequent procedure is identical with that given in the text. [Pg.553]

The modified procedure involves refluxing the N-substituted phthaUmide in alcohol with an equivalent quantity of hydrazine hydrate, followed by removal of the alcohol and heating the residue with hydrochloric acid on a steam bath the phthalyl hydtazide produced is filtered off, leaving the amine hydrochloride in solution. The Gabriel synthesis has been employed in the preparation of a wide variety of amino compounds, including aliphatic amines and amino acids it provides an unequivocal synthesis of a pure primary amine. [Pg.560]

Oximes (compare Section III,74,B). The following procedure has wide application. Dissolve 0-5 g. of hydroxylamine hydrochloride in 2 ml. of water, add 2 ml. of 10 per cent, sodium hydroxide solution and 0-2 g. of the aldehyde (or ketone). If the latter is insoluble, add just sufficient alcohol to the mixture to give a clear solution. Heat the mixture under reflux for 10-15 minutes, and then cool in ice. If crystals separate, filter these off, and recrystallise from alcohol, dilute alcohol, benzene or light petroleum (b.p. 60-80°). If no solid separates on cooling, dilute with 2-3 volumes of water, filter the precipitated sohd, and recrystallise. [Pg.721]

Place 125 ml. of glacial acetic acid, 7 -5 g. of purifled red phosphorus (Section II,50,d) and 2 5 g. of iodine in a 500 ml, round-bottomed flask fitted with a reflux condenser. Allow the mixture to stand for 15-20 minutes with occasional shaking until aU the iodine has reacted, then add 2 5 ml. of water and 50 g, of benzilic acid (Section IV,127). Boil the mixture under reflux for 3 hours, and filter the hot mixture at the pump through a sintered glass funnel to remove the excess of red phosphorus. Pour the hot filtrate into a cold, weU-stirred solution of 12 g. of sodium bisulphite in 500 ml, of water the latter should be acid to litmus, pro duced, if necessary, by passing sulphur dioxide through the solution. This procedure removes the excess of iodine and precipitates the diphenyl-acetic acid as a fine white or pale yellow powder. Filter the solid with suction and dry in the air upon filter paper. The yield is 45 g., m.p. [Pg.773]

The purified commercial di-n-butyl d-tartrate, m.p. 22°, may be used. It may be prepared by using the procedure described under i o-propyl lactate (Section 111,102). Place a mixture of 75 g. of d-tartaric acid, 10 g. of Zeo-Karb 225/H, 110 g. (136 ml.) of redistilled n-butyl alcohol and 150 ml. of sodium-dried benzene in a 1-litre three-necked flask equipped with a mercury-sealed stirrer, a double surface condenser and an automatic water separator (see Fig. Ill, 126,1). Reflux the mixture with stirring for 10 hours about 21 ml. of water collect in the water separator. FUter off the ion-exchange resin at the pump and wash it with two 30-40 ml. portions of hot benzene. Wash the combined filtrate and washings with two 75 ml. portions of saturated sodium bicarbonate solution, followed by lOu ml. of water, and dry over anhydrous magnesium sulphate. Remove the benzene by distillation under reduced pressure (water pump) and finally distil the residue. Collect the di-n-butyl d-tartrate at 150°/1 5 mm. The yield is 90 g. [Pg.952]

Alternatively, use the following procedure in which triethylamine replaces potassium acetate as the basic catalyst. Place 2 1 g. (2-0 ml.) of purified benzaldehyde, 2 0 ml. of anhydrous triethylamine and 5 0 ml. of A.R. acetic anhydride in a 200 ml. round-bottomed flask, equipped with a short reflux condenser and a calcium chloride drying tube. Boil the solution gently for 24 hours—heating may be interrupted. Incorporate a steam distillation apparatus in the flask and steam distil until the distillate is no longer cloudy (about 100 ml.) and then collect a further 50 ml. of the distillate di ard the steam distillate. Transfer the residue in the flask to a 400 ml. beaker, add water until the vplume is about 200 ml., then 0 2 g. of decolourising carbon, and boil for a few minutes. Filter the hot solution, and acidify the hot filtrate with 1 1 hydrochlorioiaoid... [Pg.1113]

A suspension of 3.90 g (19.6 mmol) of p-(bromomethyl)benzaldehyde (2.8) and 4.00 g (31.7 mmol) of sodium sulfite in 40 ml of water was refluxed for two hours, after which a clear solution was obtained. The reaction mixture was cooled on an ice bath resulting in precipitation of some sodium sulfite. After filtration, the solvent was evaporated. Ethanol was added to the remaining solid and the suspension was refluxed for 10 minutes. After filtering the hot solution, the filtrate was allowed to cool down slowly to -18 °C whereupon sodium (p-oxomethylphenyl)methylsulfonate (2.9) separated as colourless crystals. The extraction procedure was repeated two more times, affording 2.29 g (10.3 mmol, 53%) of the desired product. H-NMR (200 MH D2O) 5(ppm) =4.10 (s,2H) 7.44 (d,2H) 7,76 (d,2H) 9.75 (s,lH). [Pg.65]

Finally, in the last step, the chelating auxiliary had to be removed Ideally, one would like to convert 4.54 into ketone 4.55 via a retro Mannich reaction. Unfortunately, repeated attempts to accomplish this failed. These attempts included refluxing in aqueous ethanol under acidic and basic conditions and refluxing in a 1 1 acetone - water mixture in the presence of excess paraformaldehyde under acidic conditions, in order to trap any liberated diamine. Tliese procedures were repeated under neutral conditions in the presence of copper(II)nitrate, but without success. [Pg.117]


See other pages where Reflux procedure is mentioned: [Pg.1093]    [Pg.27]    [Pg.131]    [Pg.203]    [Pg.223]    [Pg.40]    [Pg.1000]    [Pg.2012]    [Pg.40]    [Pg.802]    [Pg.1093]    [Pg.27]    [Pg.131]    [Pg.203]    [Pg.223]    [Pg.40]    [Pg.1000]    [Pg.2012]    [Pg.40]    [Pg.802]    [Pg.170]    [Pg.185]    [Pg.205]    [Pg.254]    [Pg.363]    [Pg.565]    [Pg.615]    [Pg.641]    [Pg.672]    [Pg.813]    [Pg.814]    [Pg.1065]   


SEARCH



Procedure to estimate reactive zone height, reflux ratio and column diameter

Reflux distillation procedure

© 2024 chempedia.info