Radical chain polymerization 1,3-diene

Thiol-ene polymerization was first reported in 1938.220 In this process, a polymer chain is built up by a sequence of thiyl radical addition and chain transfer steps (Scheme 7.17). The thiol-ene process is unique amongst radical polymerizations in that, while it is a radical chain process, the rate of molecular weight increase is more typical of a step-growth polymerization. Polymers ideally consist of alternating residues derived from the diene and the dithiol. However, when dienes with high kp and relatively low A-, monomers (e.g. acrylates) are used, short sequences of units derived from the diene are sometimes formed. 

Raising the temperature of a radical chain reaction causes an increase in the overall rate of polymerization since the main effect is an increase in the rate of decomposition of the initiator and hence the number of primary radicals generated per unit time. At the same time the degree of polymerization falls since, according to Eq. 3.3, the rate of the termination reaction depends on the concentration of radicals (see Example 3-2). Higher temperatures also favor side reactions such as chain transfer and branching, and in the polymerization of dienes the reaction temperature can affect the relative proportions of the different types of CRUs in the chains. 

Stereospecific polymerization has particular significance for the preparation of stereoregular polymeric dienes. In the radical polymerization of butadiene or isoprene the molecular chains always consist of varying proportions of adjacent cis- and trans-1,4-units as well as 1,2- and 3,4- linked units, depending on the polymerization conditions but it is now possible, using particular ionic initiation systems to make a synthetic natural rubber that contains more than 90% cfs-l,4-isoprene repeating units (see Example 3-21). 

Isoprene can be polymerized in the laboratory by a radical chain mechanism. As shown in the following equations, the odd electron of the initially produced radical is delocalized onto both C-2 and C-4 by resonance. Either of these carbons may add to another isoprene monomer to continue the chain reaction. If C-2 adds, the process is called 1,2-addition if C-4 adds, the process is called 1,4-addition. (This is similar to the addition of electrophiles to conjugated dienes discussed in Section 11.13 and the addition of nucleophiles to a,/8-unsaturated carbonyl compounds described in Section 18.10.)... 

Further developments in the field of chain polymerization were centered on radical poly-addition. Its mechanism was firmly established in the 1930 s and attracted much attention. The interest in anionic polymerization was marginal and the activities in this field were centered at that time around Ziegler in Germany and Lebedev in Russia. Both groups were interested in polymerization of styrene and dienes initiated by sodium metal and their work led to industrial production of synthetic rubber marketed by I. G. Far-benindustrie as Buna . 

Classification of Polymers Free-Radical Chain-Growth Polymerization Cationic Chain-Growth Polymerization Anionic Chain-Growth Polymerization Stereoregular Polymers Ziegler-Natta Polymerization A WORD ABOUT... Polyacetylene and Conducting Polymers Diene Polymers Natural and Synthetic Rubber Copolymers... 

This discussion of chain polymerization has centered on free-radical polymerization of an ethenic monomer. Conjugated dienes such as 1,3-butadiene often polymerize as bifunctional monomers with 1,4-addition rather than as tetrafunctional monomers. 

Conjugated dienes can be polymerized just as simple alkenes can (Section 7.10). Diene polymers are structurally more complex than simple alkene polymers, though, because double bonds remain every four carbon atoms along the chain, leading to the possibility of cis-trans isomers. The initiator (In) for the reaction can be either a radical, as occurs in ethylene polymerization, or an acid. Note that the polymerization is a 1,4-addition of the growing chain to a conjugated diene monomer. 

Analogous principles should apply to ionically propagated polymerizations. The terminus of the growing chain, whether cation or anion, can be expected to exhibit preferential addition to one or the other carbon of the vinyl group. Poly isobutylene, normally prepared by cationic polymerization, possesses the head-to-tail structure, as already mentioned. Polystyrenes prepared by cationic or anionic polymerization are not noticeably different from free-radical-poly-merized products of the same molecular weights, which fact indicates a similar chain structure irrespective of the method of synthesis. In the polymerization of 1,3-dienes, however, the structure and arrangement of the units depends markedly on the chain-propagating mechanism (see Sec. 2b). 

Anionic polymerization of conjugated dienes and olefins retains its lithium on the chain ends as being active moities and capable of propagating additional monomer. This distinguishing feature has an advantage over other methods of polymerization such as radical, cationic and Ziegler polymerization. Many attempts have been made to prepare block copolymers by the above methods, but they were not successful in preparing the clear characterized block copolymer produced by anionic technique. 

The substituted carbon atoms in the polymer chain are asymmetric. Stereoregular polymers are produced if all these carbon atoms have the same configuiation (all d or all I) or if the d and 1 configurations occur alternately pronounced stereo-regularity is seldom achieved in radical polymerizations except perhaps at very low temperatures. When dienes are polymerized by a radical mechanism, the resulting polymers contain several distinct types of monomer unit, thus butadiene can give rise to -CH2 C(CH CH2)-, -CH CH CH CH2- cis, and -CH CH.CH CH2- trans. 

Catalysts of the Ziegler-Natta type are applied widely to the anionic polymerization of olefins and dienes. Polar monomers deactivate the system and cannot be copolymerized with olefins. J. L. Jezl and coworkers discovered that the living chains from an anionic polymerization can be converted to free radicals by the reaction with organic peroxides and thus permit the formation of block copolymers with polar vinyl monomers. In this novel technique of combined anionic-free radical polymerization, they are able to produce block copolymers of most olefins, such as alkylene, propylene, styrene, or butadiene with polar vinyl monomers, such as acrylonitrile or vinyl pyridine. 

---