Tubing quartz

Quartz Tube Method the sample is burned in a quartz tube and a stream of purified air carries the combustion gases into a hydrogen peroxide solution. 

A solution of 7-bromo-2-(fV-methylanilino)hept-2-enenitrile (145 mg, 0.52 mmol) in cyclohexane (60 ml) was placed in a quartz tube and purged with oxygen. The sample was irradiated for 8h in a Rayonet Model RPR-100 Reactor using 254 nm light. An oxygen atmosphere was maintained during... 

This chapter should be read in conjunction with Chapter 6, Coronas, Plasmas, and Arcs. A plasma is defined as a gaseous phase containing neutral molecules, ions, and electrons. The numbers of ions and electrons are usually almost equal. In a plasma torch, the plasma is normally formed in a monatomic gas such as argon flowing between two concentric quartz tubes (Figure 14.1). 

All methods of plasma production require some electrons to be present as electric-discharge initiators. For a plasma torch, the initiating electrons are introduced from a piezoelectric spark directed into argon gas flowing in the interval between two concentric quartz tubes. 

P. Bachmann, P. Geitner, H. Hydton, G. Ronanowski, and M. Thelen, "Preparation of Quartz Tubes by Centrifugal Deposition of SUica... 

AgF2 is prepared by the action of elemental fluorine on AgF or AgCl at 200°C. Both processes result in quantitative yields. Silver difluoride should be stored in Teflon, passivated metal containers, or in sealed quartz tubes. 

Ferrous orthotitanate [12160-20-2] Fe2Ti04, is orthorhombic and opaque. It has been prepared by heating a mixture of ferrous oxide and titanium dioxide. Ferrous dititanate [12160-10-0] FeTi20, is orthorhombic and has been prepared by reducing ilmenite with carbon at 1000°C. The metallic ion formed in the reaction is removed, leaving a composition that is essentially the dititanate. Ferric titanate [1310-39-0] (pseudobrookite), Fe2TiO, is orthorhombic and occurs to a limited state in nature. It has been prepared by heating a mixture of ferric oxide and titanium dioxide in a sealed quartz tube at 1000°C. 

Chromium (II) also forms sulfides and oxides. Chromium (II) oxide [12018-00-7], CrO, has two forms a black pyrophoric powder produced from the action of nitric acid on chromium amalgam, and a hexagonal brown-red crystal made from reduction of Cr202 by hydrogen ia molten sodium fluoride (32). Chromium (II) sulfide [12018-06-3], CrS, can be prepared upon heating equimolar quantities of pure Cr metal and pure S ia a small, evacuated, sealed quartz tube at 1000°C for at least 24 hours. The reaction is not quantitative (33). The sulfide has a coordination number of six and displays a distorted octahedral geometry (34). 

A Perkin-Elmer 5000 AAS was used, with an electrically heated quartz tube atomizer. The electrolyte is continuously conveyed by peristaltic pump. The sample solution is introduced into the loop and transported to the electrochemical cell. A constant current is applied to the electrolytic cell. The gaseous reaction products, hydrides and hydrogen, fonued at the cathode, are flowed out of the cell with the carrier stream of argon and separated from the solution in a gas-liquid separator. The hydrides are transported to an electrically heated quartz tube with argon and determined under operating conditions for hydride fonuing elements by AAS. 

We developed a sensor for determination of content of phosphorars in metallurgical melts. In quality of ion conductor used orthophosphate of calcium which pressed in tablets 010 mm. Tablets (mass 1-2 g) annealed at a temperature 400°C during 7-10 h. Tablets melts then in a quartz tube and placed the alloy of iron containing 1 mass % P. Control of sensor lead on Fe - P melts. Information on activities (effective concentration) of phosphorars in Fe - P melts was received. It is set that the isotherm of activity of phosphorars shows negative deviations from the Raouls law. Comparison them with reliable literary inforiuation showed that they agree between itself. Thus, reliable data on activities (effective concentration) of phosphorars in metallic melts it is possible to received by created electrochemical sensor for express determination. 

Graphite [7782-42-5]. Treated with hot 1 1 HCl. Filtered, washed, dried, powdered and heated in an evacuated quartz tube at 1000° until a high vacuum was obtained. Cooled and stored in an atmosphere of helium [Craig, Van Voorhis and Bartell 7 Phys Chem 60 1225 1956]. 

A solution of 0.17 g (51) in 160 ml benzene is stirred magnetically and irradiated for 6 hr with a Hanau NK 6/20 low-pressure mercury lamp (main emission at 2537 A) placed in a central water-cooled quartz tube. Cyrstalliza-tion of the crude product gives 0.15 g (52) (88%). 

Quarz-keil, m. (Optica) quartz wedge, -kiesel, m. quartz gravel, -kristall, m. quartz crystal, rock crystal. -lager, n. quartz deposit, -linse, /. quartz lens, -mehl, -pulver, n. quartz powder- -rohr, n., -rohre, /. quartz tube, -sand, m. quartz sand, -scheibe, /. 

A similar unit, modified in details such as location of condenser, use of an agitator and shape of the vessel, was used by Fisher and Whitney . Further substantial modifications to permit interface location of specimens, cooling of specimens and operation under applied pressure, have been described by Fisher . Earlier laboratory test methods tried by Fisher and Whitney included exposure of specimens heated by their own electrical resistance and of tubular specimens containing a pencil-type resistance-wire heater in a quartz tube. 

The inductively coupled plasma source (Fig. 20.11) comprises three concentric silica quartz tubes, each of which is open at the top. The argon stream that carries the sample, in the form of an aerosol, passes through the central tube. The excitation is provided by two or three turns of a metal induction tube through which flows a radio-frequency current (frequency 27 MHz). The second gas flow of argon of rate between 10 and 15 L min-1 maintains the plasma. It is this gas stream that is excited by the radio-frequency power. The plasma gas flows in a helical pattern which provides stability and helps to isolate thermally the outside quartz tube. 

---