Purification, general ethers

Modem commercial wet-acid purification processes (see Fig. 4) are based on solvents such as C to Cg alcohols, ethers, ketones, amines, and phosphate esters (10—12). Organic-phase extraction of phosphoric acid is accompHshed in one or more extraction columns or, less frequently, in a series of countercurrent mixer—settlers. Generally, 60—75% of the feed acid P2 s content is extracted into the organic phase as H PO. The residual phosphoric acid phase (raffinate), containing 25—40% of the original P2O5 value, is typically used for fertilizer manufacture such as triple superphosphate. For this reason, wet-acid purification units are almost always located within or next to fertilizer complexes. 

Because of their zwitterionic nature, amino acids are generally soluble in water. Their solubility in organic solvents rises as the fat-soluble portion of the molecule increases. The likeliest impurities are traces of salts, heavy metal ions, proteins and other amino acids. Purification of these is usually easy, by recrystallisation from water or ethanol/water mixtures. The amino acid is dissolved in the boiling solvent, decolorised if necessary by boiling with Ig of acid-washed charcoal/lOOg amino acid, then filtered hot, chilled, and set aside for several hours to crystallise. The crystals are filtered off, washed with ethanol, then ether, and dried. 

A -( 1-Chloro- or bromoalkyl)amides are generally moisture-sensitive, unstable compounds, which are often directly used without further purification. Standard Lewis acids such as boron trifluoride-diethyl ether, aluminum(lll) chloride, zinc(II) chloride, tin(IV) chloride and titani-um(IV) chloride are used to generate the /V-acyliminium ion, although sometimes a catalyst is not necessary. 

In a typical procedure61144 the sulfonyl chloride in ether is added to an etheral solution of the diazoalkane and triethylamine. Filtration and evaporation gives the relatively pure thiirane dioxide. Further purification can be easily achieved by recrystallizations preferentially below room temperature in order to avoid fragmentation of the product into sulfur dioxide and the olefin. In general, when the temperature of the above reaction is lowered, the yields are improved without a drastic decrease in reactivity144. Many thiirane dioxides have been successfully synthesized through this method and a detailed list of them can be found elsewhere2. 

The alkanephosphonic acid dichlorides obtained by these methods are converted with amines, with all reactions carried out in solvents such as acetone, benzene, or diethyl ether at 10°C with triethylamine as HC1 captor. The conversion runs quantitatively followed by a purification with the help of column chromatography with chloroform/methanol in a ratio of 9 1 as mobile phase. The alkanephosphonic acid bisdiethanolamides could be obtained as pure substances with alkane residues of C8, C10, C12, and Ci4. The N-(2-hydroxyethane) alkanephosphonic acid 0,0-diethanolamide esters were also prepared in high purity. The obtained surfactants are generally stable up to 100°C. Only the alkanephosphonic acid bismonomethylamides are decomposed beneath this temperature forming cyclic compounds. 

All solvents used for general applications were of reagent grade. For special purposes, purification of solvents was effected using standard procedures. All other reagents were used as supplied commercially except as noted. A solution of chloromethyl methyl ether (6 mmole/mL) in methyl acetate was prepared by adding acetyl chloride (141.2 g, 1.96 mol) to a mixture of dimethoxy methane (180 mL, 2.02 mol) and anhydrous methanol (5.0 mL, 0.12 mol).20 The solution was diluted with 300 mL of 1,1,2,2-tetrachloroethane and used as a stock solution for the chloromethylation experiments. 

These thermolysis reactions normally produce polymeric products, free of the cyclic analogs, in essentially quantitative yield and in sufficient purity to give satisfactory elemental analysis upon removal of the sHyl ether byproduct under vacuum. Final purification is generally achieved by precipitation of the polymer into a non-solvent such as hexane. With the exception of poly(diethylphosphazene) (2), which is insoluble in all common solvents (see below), the new polymers are readily soluble in CH CU and CHCU. In addition, the phenyl substituted compounds (3-6) are soluble in THF andvanous aromatic solvents. None of the polymers are water-soluble however, Me2PN]n (1) is soluble in a 50 50 water/THF mixture. 

General Considerations. The following chemicals were commercially available and used as received 3,3,3-Triphenylpropionic acid (Acros), 1.0 M LiAlH4 in tetrahydrofuran (THF) (Aldrich), pyridinium dichromate (Acros), 2,6 di-tert-butylpyridine (Acros), dichlorodimethylsilane (Acros), tetraethyl orthosilicate (Aldrich), 3-aminopropyltrimethoxy silane (Aldrich), hexamethyldisilazane (Aldrich), tetrakis (diethylamino) titanium (Aldrich), trimethyl silyl chloride (Aldrich), terephthaloyl chloride (Acros), anhydrous toluene (Acros), and n-butyllithium in hexanes (Aldrich). Anhydrous ether, anhydrous THF, anhydrous dichloromethane, and anhydrous hexanes were obtained from a packed bed solvent purification system utilizing columns of copper oxide catalyst and alumina (ether, hexanes) or dual alumina columns (tetrahydrofuran, dichloromethane) (9). Tetramethylcyclopentadiene (Aldrich) was distilled over sodium metal prior to use. p-Aminophenyltrimethoxysilane (Gelest) was purified by recrystallization from methanol. Anhydrous methanol (Acros) was... 

General. Toluene, chlorobenzene, and o-dichlorobenzene were distilled from calcium hydride prior to use. 4-Dimethylaminopyridine (Aldrich Chemical Co) was recrystalled (EtOAc), and the other 4-dialkylaminopyridines were distilled prior to use. PEG S, PEGM s, PVP s, and crown ethers were obtained from Aldrich Chemical Co., and were used without purification. BuJ r and BU. PBr were recrystallized (toluene). A Varian 3700 VrC interfaced with a Spectraphysics SP-4000 data system was used for VPC analyses. A Dupont Instruments Model 850 HPLC (also interfaced with the SP-4000) was used for LC analyses. All products of nucleophilic aromatic substitution were identified by comparison to authentic material prepared from reaction in DMF or DMAc. Alkali phenolates or thiol ates were pre-formed via reaction of aqueous NaOH or KOH and the requisite phenol or thiophenol in water under nitrogen, followed by azeotropic removal of water with toluene. The salts were transferred to jars under nitrogen, and were dried at 120 under vacuum for 20 hr, and were stored and handled in a nitrogen dry box. 

Apart from 1,3,4-oxadiazole (b.p. 150°C), its lower alkyl derivatives and some dihydro compounds, 1,3,4-oxadiazoles are generally solids. In synthesis, the common method of purification is by crystallization of the crude reaction product. A few oxadiazoles, for example, alkyl ethers and acetates derived from 2,5-dihydro-2-hydroxy-2,5,5-trialkyl-l,3,4-oxadiazoles (cf. (38)), have been purified by distillation under reduced pressure. In some cases, chromatography over silica gel has been used. 

General Procedure for Microwave-Induced Fries Rearrangement. Neat substrate (0.01 mol) was mixed with the support (1 3, w/w) in a beaker and was exposed to microwave irradiation for 7 min. After cooling to room temperature the product was extracted with diethyl ether. Evaporation of the solvent gave almost pure product. Further purification was carried out by recrystallization or column chromatography on silica gel. 

---