Typical Procedures

It is possible to use the quantum states to predict the electronic properties of the melt. A typical procedure is to implement molecular dynamics simulations for the liquid, which pemiit the wavefiinctions to be detemiined at each time step of the simulation. As an example, one can use the eigenpairs for a given atomic configuration to calculate the optical conductivity. The real part of tire conductivity can be expressed as... 

In a typical procedure, a solution of 0.175 mmol of L- -amino acid and 0.175 mmol of NaOH in 1 ml of water was added to a solution of 0.100 mmol of Cu(N03)2in 100 ml of water in a 100 ml flask. Tire pH was adjusted to 6.0-6.5. The catalyst solution was cooled to 0 C and a solution of 1.0 mmol of 3.8c in a minimal amount of ethanol was added, together with 2.4 mmol of 3.9. The flask was sealed carefully. After 48 hours of stirring at 0 C the reaction mixture was extracted with ether, affording 3.10c in quantitative yield After evaporation of the ether from the water layer (rotary evaporator) the catalyst solution can be reused without a significant decrease in enantioselectivity. 

MejSiCI - Nal - CH3CN as an Efficient and Practical Reducing Agent for Benzoic Alcohols. A typical procedure for the present reduction is as follows To a mixture of MejSiCI (1.54 ml, 12 mmol), Nal (1.8 g, 12 mmol), and acetonitrile (0.6 ml, 12 mmol) was added a solution of 1-phenylethanol (244 mg, 2 mmol) in hexane (2 ml). The mixture was stirred for 24 h at room temperature. Dilution with water, extraction with ether and subsequent isolation process gave ethylbenzene (158 mg) with sufficient purity in 75% yield. ... 

Anilines react with ct-haloacetophenones to give 2-arylindoles. In a typical procedure an W-phenacylaniline is heated with a tw o-fold excess of the aniline hydrobromide to 200-250°C[1]. The mechanism of the reaction was the subject of considerable investigation in the 1940s[2]. A crucial aspect of the reaction seems to be the formation of an imine of the acetophenone which can isomerize to an aldimine intermediate. This intermediate apparently undergoes cyclization more rapidly (path bl -> b2) than its precursor (Scheme 7.3). Only with very reactive rings, e.g, 3,5-dimethoxyaniline, has the alternative cydiz-ation (path al a2) to a 3-arylindole been observed and then only under modified reaction conditions[3],... 

One approach called enzymatic resolution, involves treating a racemic mixture with an enzyme that catalyzes the reaction of only one of the enantiomers Some of the most commonly used ones are lipases and esterases enzymes that catalyze the hydrol ysis of esters In a typical procedure one enantiomer of the acetate ester of a racemic alcohol undergoes hydrolysis and the other is left unchanged when hydrolyzed m the presence of an esterase from hog liver... 

Representative Method The best way to appreciate the importance of the theoretical and practical details discussed in the previous section is to carefully examine the procedure for a typical precipitation gravimetric method. Although each method has its own unique considerations, the determination of Mg + in water and waste-water by precipitating MgNH4P04 6H2O and isolating Mg2P20y provides an instructive example of a typical procedure. 

Representative Method Although each volatilization gravimetric procedure has its own unique characteristics, the following indirect method for the determination of Si in ores and alloys by formation of volatile SiF4 provides an instructive example of a typical procedure. 

The preparation of high molecular weight PPT in HMPA/NMP shows a strong dependence of inherent viscosity on reactant concentrations. In 2 1 (by volume) HMPA/NMP, the highest inherent viscosity polymer is obtained when each reactant is present in concentrations of ca 0.25 M higher and lower concentrations result in the formation of polymer of lower inherent viscosities. A typical procedure is as foUows 1,4-phenylenediamine, HMPA, and NMP are added to an oven-dried resin ketde equipped with a stirrer and stirred for ca 15 min with cooling to — 15°C, foUowed by the addition of powdered terephthaloyl chloride to the rapidly stirred solution. The reaction mixture changes to a thick, opalescent, paste-like gel in ca 5 min. 

Pyrolysis. Benzene undergoes thermal dehydrocondensation at high temperatures to produce small amounts of biphenyls and terphenyls (see Biphenyl AND terphenyls). Before the 1970s most commercial biphenyl was produced from benzene pyrolysis. In a typical procedure benzene vapors are passed through a reactor, usually at temperatures above 650°C. The decomposition of benzene iato carbon and hydrogen is a competing reaction at temperatures of about 750°C. Biphenyls are also formed when benzene and ethylene are heated to 130—160°C ia the presence of alkaH metals on activated AI2O3 (33). 

Cyanogen azide is a useful reagent for conversion of pyrrolidine enamines of 3-keto steroids to A-norsteroids. " Ring contractions can be carried out in the presence of 17j5-hydroxy, 17j -acetoxy, 20-keto groups and isolated double bonds. In a typical procedure, 17j -hydroxy-5a-androstan-3-one (partial formula 8) is converted into the enamine (9) by pyrrolidine in benzene... 

During 1961-2 four independent groups almost simultaneously reported the first syntheses of D-norsteroids, based on the photolysis of 16-diazo-17-ketones. In a typical procedure. Cava and Moroz ° convert the 16-oximino-17-one (93) derived from estrone methyl ether (92) to the diazoketone (94)... 

The carbonyl group of carbohydrates can be reduced to an alcohol function. Typical procedures include catalytic hydrogenation and sodium borohydride reduction. Lithium aluminum hydride is not suitable, because it is not compatible with the solvents (water, alcohols) that are requited to dissolve caibohydrates. The products of caibohydrate reduction aie called alditols. Because these alditols lack a car bonyl group, they aie, of course, incapable of forming cyclic hemiacetals and exist exclusively in noncyclic forms. 

By the chlorination of 3-ethynyl-, 4-ethynyl-, and 5-ethynyl-l-methylpyrazole with KOCl the corresponding compounds were synthesized in 98%, 100%, and 94% yields. The typical procedure is as follows To an aqueous solution of KOX (0.64 N) in 12.5% KOH, prepared from the corresponding halogen and potassium hydroxide in water at 5-10°C, was added the terminal acetylene, followed by stirring at room temperature until the complete disappearance of the starting material. 

Thermoplastic polyurethane (TPU) is a type of synthetic polymer that has properties between the characteristics of plastics and rubber. It belongs to the thermoplastic elastomer group. The typical procedure of vulcanization in rubber processing generally is not needed for TPU instead, the processing procedure for normal plastics is used. With a similar hardness to other elastomers, TPU has better elasticity, resistance to oil, and resistance to impact at low temperatures. TPU is a rapidly developing polymeric material. 

Following is a typical procedure for the emulsion polymerization of hydrophobic monomers in batch fashion. The first step in this process is the preparation of the continuous phase solution. As mentioned before, water is usually selected as the base material of the continuous phase for the emulsion polymerization of hydrophobic... 

Stefanovich, Leonov and Venevtsev [417] describe a typical procedure of SHG measurement. The scheme of the SHG equipment enables to perform measurements at different temperatures, as shown in Fig. 96. SHG measurements of some tantalum and niobium complex fluoride and oxyfluoride compounds in the powdered form were reported in [206, 211] and some results are presented in Table 58. 

Dimethyl 7-Hydroxy-2-(jV-methylanilino)-l-benzoxepin-3,4-dicarboxylate (1 a) Typical Procedure 181... 

Di-fm-butyl-5-[(4-dimethylamino)phenyl[-2-(4-tolyl)oxepin (le) Typical Procedure 187... 

---