Price purchase

The tests concluded that it was possible to use real time X-ray to inspect incoming frozen fish blocks 100% and giving a completely accurate assessment of the quality of the blocks to enable the factory to calculate the correct purchase price as a function of the bone content. 

In the FIFO method, the units taken out of storage are valued at their purchase price beginning with the earliest item purchased. If a number of units m are removed from inventory during the period, the total cost of these items on a FIFO basis is given by ... 

Performance Data for Vacttum-Shelf Dryers The purchase price of a vacuum-shelf dryer depends upon the cabinet size and number of shelves per cabinet. For estimating purposes, typical prices (1985) and auxiliai y-emiipment requirements are given in Table 12-12. Installed cost of the equipment will be roughly 100 percent of the carbon steel purchase cost. 

Cost Data for Kilns Purchase prices, weights, and horsepower requirements of typical units are given in Table 12-21. Installed costs will run to from 300 to 500 percent of purchase cost. Maintenance will average 5 to 10 percent of the total installed cost per year but is dependent largely on the hfe of the refractoiy lining. 

Kiln size, diameter X length Total purchase price includes drive, burner, and controls (not including hrick)f... 

Diameter, m Length, m Heating surface, m Working capacity, m l Agitator speed, r/min Drive, kW Weight, kg Purchase price (1995) ... 

As indicated, one of the factors affecting the selection of a filter is total cost of carrying out the separation with the selected machine. An important component of this cost item is the installed cost of the filter, which starts with the purchase price. 

Purchase Price Typical purchase prices, including drive motors, of tubular and disk sedimenting centrifuges are given in Table 18-16. The price will vary upward with the use of more exotic materials of construc tion, the need for explosion-proof elec trical gear, the type of enclosure required for vapor containment, and the degree of portability, and this holds for all types of centrifuges. 

TABLE 18-16 Typical Purchase Prices/ Including Drive Motors/ of Tubular and Disk Sedimenting CentrifugeS/ 1996... 

Type Bowl diameter, in (mm) Approximate 2, value, units of 10 fri (10 m ) Designation Purchase price, 1996 ... 

Year Bituminous coal and lignite, /Mg ( /US ton) Natural gas at the wellhead, 71000 ( 71000 std ft ) Crude oil, domestic first purchase price, 7nd ( 7hLl)... 

Purchase price of equipment turbine, compressor, auxiliary equipment, and heat recovery equipment, if desired. 

Make no mistake about it - air pollution abatement, especially based upon end-of-pipe treatment technologies is expensive. Not too long ago the prevailing attitude among industry stakeholders was that air pollution control was simply a part of the cost of doing business, and that add-on costs associated with compliance simply had to be passed on to the consumer s purchase price for products. With the intensity of international competition in the chemical and allied industries, this philosophy simply does not cut it anymore. 

Any comparison of the cost of computer applications requires the assessment of many factors in addition to the purchase price identified by the vendor. (See note above for a detailed discussion of costs.)... 

Life cycle cost (LCC) calculations are made to make sure that both the purchase price and the operating costs for life cycle are considered in investment decisions. In the chapter the basic calculation methods and sensitivity analysis are introduced. Examples of calculation results and references to LCC information sources are given. 

The aim of life cycle cost calculations is to ensure that investment decisions are not made solely on the basis of a low purchase price, but that the life cycle operating costs are considered in the equation. 

Another way to utilize LCC calculations is in support of a purchase. The supplier can offer both the purchase price and an estimate of the present value of the life cycle operating costs At the same time the supplier guarantees the operating cost for some period, for example, 3 years. If these target costs are exceeded, the supplier pays a penalty, and if the operating costs were overestimated, the supplier and the customer share the bonus. 

The purchase price of an initial charge of catalyst is but one factor entering into the cost of using a catalyst. For noble-metal catalysts, which have high reclaim value, this price is in itself relatively unimportant. The number of greater significance is the cost of the catalyst in use, that is, the cost of the catalyst when the value of reclaimed metal has been deducted,... 

Sion to our assumptions about the initial purchase price and the cost of gasoline. Figure 1 shows the LCC of the hybrid and the conventional car over the ten-year period as a function of the cost of gasoline. When gas prices are approximately 3 per gallon, the two cars cost about the same. This value is referred to as the break-even point. If gas prices reach 3.75 per gallon, the approximate cost in Japan, the hybrid car is more economical. Sensitivity analysis can also be conducted for other input variables, such as initial purchase price, miles driven per year and actual fuel economy. 

The Tax Code contains various provisions that may affect the demand for energy from specific sources. In the transportation area, purchasers of electric vehicles may claim a credit against their income tax liability for a portion of the purchase price. Taxpayers who pur-... 

If the purchaser is not satisfied with the wire rope service, he or she shall send the properly preserved sample or a sample of the rope from an unused section to any testing laboratory mutually agreed upon by the purchaser and the manufacturer, with instructions to make a complete API test, and notify the manufacturer to have a representative present. If the report indicates compliance with specifications, the purchaser shall assume cost of testing otherwise, the manufacturer shall assume the expense and make satisfactory adjustments not exceeding full purchase price of the rope. If the report indicates noncompliance with specifications, the testing laboratory shall forward a copy of the test report to the manufacturer. 

In designing the asset register format for the specific location items such as manufacturer/supplier, purchase price and date, order no., cost code, function, parts/spares, guidance note reference and insurance inspections should be catered for. While carrying out the survey for the asset register, all the information found on plant and equipment nameplates should be recorded as, during their life, these tend to be lost or painted over. 

The purchase price of some instruments may include set-up and check-out by a manufacturer s representative. In such cases, the laboratory operator should only check for physical condition of a shipment and call the representative about its arrival. Other equipment will generally be set up at its permanent location as soon as it is unpacked and checked. Supplies will be taken to their designated storage areas. The accompanying warranty cards should be filled out and mailed as soon as possible. 

---