Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Product inspections

The discussion that follows will show the effects of several operating variables on product inspections. The effects of the variables are illustrated best by deep desulfurization of heavier gas oils. [Pg.64]

Are incoming products, semi-finished products, and finished products inspected and tested in accordance with documented procedures ... [Pg.82]

Plant Production Inspection Centre VUhonvuorenkatu 11 C, V Floor,... [Pg.23]

Teacher s Manual. Fishery Products Inspection UJ5. Department of Commerce National Oceanic and Atmospheric Administration National Marine Fisheries Service. [Pg.66]

Product inspections and yield data for typical alkylates produced from propylene, butenes, and pentenes are presented in Table II. In general, the optimum operating con-... [Pg.107]

Quantitative tests are rarely conducted in magazines and for production inspection purposes except for a test devised by Bergmann and Junk [62] in which the quantity of acid products (calculated as NO) evolved by the powder is determined by titration. The quantity of NO evolved on heating for 2 hr at a temperature of 132°C should not exceed 2.5 cm3 NO per 1 g of powder. (For more details see Vol. II p. 26.) Other quantitative tests are usually employed in research. [Pg.558]

Design manufacture, final product inspection, and testing (module H)... [Pg.13]

The quality system manual is applicable to (company name) products, activities, and services and includes design manufacture and final product inspection and testing. [Pg.35]

The international standard ISO 9001 2000 specifies quality system requirements for use where a contract between the company and customers requires demonstration of the capability to design and supply the product in compliance with the applicable regulatory requirements and customer satisfaction. The contents of the adopted standard refer to design, manufacture, and final product inspection and testing. No exclusions permitted. [Pg.125]

ISO 9001 1994, Quality System — Model for Quality Assurance in Design, Development, Production, Installation, and Servicing ISO 9001 2000, Quality Management System Requirements. Design, Manufacture, and Final Product Inspection and Testing. [Pg.126]

The international standard ISO 9003 1994 was established by Technical Committee ISO/TC 178, and is based on British standard 5750 1987 series, European standard EN 29000 1987 series, and international standards ISO 9000 1987 series. The standard was adopted by the company to provide objective evidence that the company s operations of final product inspection and testing are in compliance with the requirement of this standard. However, this third edition canceled and replaced the second edition (ISO 9003 1994). The quality manual QM-4 is revised in accordance with the corresponding changes specified in the third edition of ISO 9001 2000 to specify quality system requirements for use where a contract between the company and customer requires the demonstration of capability of final product inspection and testing with customer satisfaction. The permissible exclusions are made to ... [Pg.251]

The quality system manual provides descriptions of management efforts and initiatives to ensure customer requirements are met with continuous improvement in the hnal product inspection and testing activities. The quality system manual and procedures ... [Pg.276]

A similar agreement to the MRAs is the Protocol to the European Agreement on Conformity Assessment and Acceptance of Industrial Products (PEC A) made public by the EC in March 2002. It was prepared in order to facilitate the operation of the annex on GMP for medicinal products inspections and batch certification to such PECAS. The type of information that should be exchanged between the EU and associated countries and the obligations with respect to joint inspections and inspector training are also delineated. [Pg.875]


See other pages where Product inspections is mentioned: [Pg.981]    [Pg.983]    [Pg.35]    [Pg.7]    [Pg.1165]    [Pg.347]    [Pg.148]    [Pg.562]    [Pg.214]    [Pg.132]    [Pg.12]    [Pg.48]    [Pg.282]    [Pg.6]    [Pg.29]    [Pg.148]    [Pg.804]    [Pg.82]    [Pg.16]    [Pg.149]    [Pg.236]    [Pg.320]    [Pg.75]    [Pg.340]    [Pg.510]    [Pg.13]    [Pg.462]    [Pg.300]    [Pg.756]    [Pg.462]    [Pg.15]    [Pg.89]    [Pg.95]    [Pg.98]    [Pg.106]    [Pg.112]    [Pg.108]   
See also in sourсe #XX -- [ Pg.103 ]




SEARCH



Drug products preapproval inspections

Finished-product inspection

Poultry Products Inspection Act

Product-specific preapproval inspections

Production inspection

Production inspection

Re-inspection of repaired and reworked product

Visual Inspection of Lyophilized Product Parenterals

© 2024 chempedia.info