Pressure generators

High-pressure vessel to contain the sample cell. 

Usually the required pressures are obtained with a reciprocating 

---

There are two classes of acetylene generators the low pressure generator which operates below 108.2 kPa (15.7 psi), and the medium pressure generator which operates between 108.2 and 204.7 kPa (29.7 psi). The latter is more prevalent in the United States. 

The fluid dehvery in an air-spray system can be pressure or suction fed. In a pressure-fed system, the fluid is brought to the atomizer under positive pressure generated with an external pump, a gas pressure over the coating material in a tank, or an elevation head. In a suction system, the annular flow of air around the fluid tip generates sufficient vacuum to aspirate the coating material from a container through a fluid tube and into the air stream. In this case, the paint supply is normally located in a small cup attached to the spray device to keep the elevation differential and frictional pressure drop in the fluid-supply tube small. 

Once a matrix of particles is formed, whether filter cake, thickened underflow, or soil, applying a current to the fluid causes a movement of ions in the water and, with the ions, water of hydration. The phenomenon is called electro osmosis. The pressure generated on the fluid is given by (127) ... 

Piezoelectric Transducers Certain ciystals produce a potential difference between their surfaces when stressed in appropriate directions. Piezoelectric pressure transducers generate a potential difference proportional to a pressure-generated stress. Because of the extremely high electrical impedance of piezoelectric crystals at low frequency, these transducers are usually not suitable for measurement of static process pressures. 

Transducers The ciirrent-to-pressiire transducer (I/P transducer) is a conversion interface that accepts a standard 4-20 rnA input current from the process controller and converts it to a pneumatic output in a standard pneumatic pressure range (normally (),2-L0 bar [3-15 psig] or, less frequently, 0,4-2,0 bar [6-30 p.sig]). The output pressure generated by the transducer is connected directly to the pressure connection on a spring-opposed diaphragm actuator or to the input of a pneumatic valve positioner. 

The suction pressure generated is equal to the liquid head difference across the annular baffle as magnified by G. The maximum suction that can be realized, assuming neghgible vapor pressure, is I atm. For example, with a differential liquid level of 2 cm (0.79 in) of water across the annulus under 500g, the suction generated by the siphon is 0.98 atm. 

Static head generated by a centrifugal blower depends on RPM alone for a given internal construction and a given set of dimensions. Pressure generated depends not only on RPM, but also on the density of the fluid. Flow depends on conditions outside the blower and so does the power needed. Therefore, blower performance should be characterized first by the head as a function of RPM thereafter, studies can be extended to describe the flow. 

Actual measurement results are shown in Figure 3.4.3 Here a ROTOBERTY reactor was used with a two-stage blower pumping air at room conditions over three catalyst beds with 5, 10, and 15 cm of catalyst volume. Pressure generated was measured by a water U-tube... 

Figure 3.4.3 shows that the measured results fit the quadratic equation well for pressure generated. It also shows that the pressure generated is independent of flow since three different quantities of catalyst were used. Since the pressure drop remained constant, then flow must have been different over the three quantities of catalysts. The flow adjusted itself to match the constant pressure generated by the blower. 

The catalyst bed that was charged to the reactor is now a restriction, calibrated for flow vs. pressure drop. The pressure drop equals the pressure generated by the blower, which in turn depends on the RPM. In essence, the differential pressure measurement was eliminated by calibrating the flow directly with RPM. 

The blower is calibrated at the factory for pressure generated vs. RPM. This can be checked with a U-tube or slanted tube for measuring the... 

Monitor stock, e.g. temperature, pressure, reaction, inhibitor content, degradation of substance, deterioration of packaging or containers/corrosion, leakages, condition of label, expiry date, undesirable by-products (e.g. peroxides in ethers) Spillage control bund, spray, blanket, containment. Drain to collection pit Decontamination and first-aid provisions, e.g. neutralize/destroy, fire-fighting Contain/vent pressure generated to a safe area... 

The first step in the design of protechon against overpressure is to consider ah contingencies which may cause overpressure, and to evaluate them in terms of the pressures generated and/or the rates at which fluids must be relieved. 

In this type of reaetion, no permanent gas is generated. The pressure generated by the reaetion is due to the inereasing vapor pressure of the reaetants, produets, and/or inert solvent as the temperature rises. 

Can equipment be designed sufficiently strong to totally contain the maximum pressure generated, even if the worst credible event occurs ... 

Pressure containment can also be provided by using piping systems with a pressure rating above the anticipated maximum pressure generated during a deflagration. 

Theoretical research is then discussed. Most theoretical research has concentrated on blast generation as a function of flame speed. Models of flame-acceleration processes and subsequent pressure generation (CFD-codes) are described as well, but in less detail. 

---