Polymerization, anionic methods

This chapter aims to give an overview on the recent advances in the synthesis of PCNs through the in-situ 1,3-butadiene homo- and copolymerization technique. To this purpose, we distinguished in-situ polymerization approaches on the basis of the polymerization method anionic or insertion/coordinative. However, before discussing on the topic of this chapter, we wish to briefly recall some peculiar aspects of clay minerals, PNs, and their methods of preparation. 

A brief review has appeared covering the use of metal-free initiators in living anionic polymerizations of acrylates and a comparison with Du Font s group-transfer polymerization method (149). Tetrabutylammonium thiolates mn room temperature polymerizations to quantitative conversions yielding polymers of narrow molecular weight distributions in dipolar aprotic solvents. Block copolymers are accessible through sequential monomer additions (149—151) and interfacial polymerizations (152,153). 

The chemistry of polymerization of the oxetanes is much the same as for THE polymerization. The ring-opening polymerization of oxetanes is primarily accompHshed by cationic polymerization methods (283,313—318), but because of the added ring strain, other polymerization techniques, eg, iasertion polymerization (319), anionic polymerization (320), and free-radical ring-opening polymerization (321), have been successful with certain special oxetanes. 

Photoinitiators provide a convenient route for synthesizing vinyl polymers with a variety of different reactive end groups. Under suitable conditions, and in the presence of a vinyl monomer, a block AB or ABA copolymer can be produced which would otherwise be difficult or impossible to produce by another polymerization method. Moreover, synthesis of block copolymers by this route is much more versatile than those based on anionic polymerization, since a wider range of a monomers can be incorporated into the blocks. 

A discussion of this polymerization method would not be complete without mention of the development of specialized glassware utilized over the years. It has evolved from very elaborate, sophisticated, and specially designed glassware to fairly simple setups. Initially, elaborate break-seal technology was used to complete the entire polymerization process,143 similar to anionic polymerization methodology.17 Break-seal techniques were employed to fully understand many monomer structure-reactivity relationships these techniques are no longer needed. 

The purpose of this paper is to thoroughly discuss the ability of anionic living polymerization methods to yield tailor-made polymers, and to discuss a number of examples of structures that have been obtained by these methods and adequately characterized. 

Polystyrene is unusual among commodity polymers in that we can prepare it in a variety of forms by a diversity of polymerization methods in several types of reaction vessel. j Polystyrene may be atactic, isotactic, or syndiotactic. Polymerization methods include free radical, cationic, anionic, and coordination catalysis. Manufacturing processes include bulk, solution, suspension, and emulsion polymerization. We manufacture random copolymers ... 

Why is it possible to manufacture polystyrene by radical, anionic, cationic and coordination polymerization methods ... 

CONVERGENT (SELF-BRANCHING) ANIONIC POLYMERIZATION METHOD... 

Most of the methods for synthesizing block copolymers were described previously. Block copolymers are obtained by step copolymerization of polymers with functional end groups capable of reacting with each other (Sec. 2-13c-2). Sequential polymerization methods by living radical, anionic, cationic, and group transfer propagation were described in Secs. 3-15b-4, 5-4a, and 7-12e. The use of telechelic polymers, coupling and transformations reactions were described in Secs. 5-4b, 5-4c, and 5-4d. A few methods not previously described are considered here. 

Hawker et al. 2001 Hawker and Wooley 2005). Recent developments in living radical polymerization allow the preparation of structurally well-defined block copolymers with low polydispersity. These polymerization methods include atom transfer free radical polymerization (Coessens et al. 2001), nitroxide-mediated polymerization (Hawker et al. 2001), and reversible addition fragmentation chain transfer polymerization (Chiefari et al. 1998). In addition to their ease of use, these approaches are generally more tolerant of various functionalities than anionic polymerization. However, direct polymerization of functional monomers is still problematic because of changes in the polymerization parameters upon monomer modification. As an alternative, functionalities can be incorporated into well-defined polymer backbones after polymerization by coupling a side chain modifier with tethered reactive sites (Shenhar et al. 2004 Carroll et al. 2005 Malkoch et al. 2005). The modification step requires a clean (i.e., free from side products) and quantitative reaction so that each site has the desired chemical structures. Otherwise it affords poor reproducibility of performance between different batches. 

Among the two ionic polymerization techniques mentioned above, a living anionic polymerization should show the best possible control of polymer architecture and composition. Mono dispersed homopolymers, complex-block, graft, star, and miktoarm architectures have been accessible primarily by anionic polymerization methods [22]. They have been used to grow polymer brushes from various small particles such as silica gels graphite,carbon black, and flat surfaces [23-26]. Recent results have been reported on living anionic polymerizations on clay [27] and silica nanoparticles [28,29]. 

To control the sequence length of HEMA-STY triblock copolymer, Okano et al. [81] later adopted the anionic living-polymerization method. Junction... 

The commerical polybutadiene (a highly 1,4 polymer with about equal amounts of cis and trans content) produced by anionic polymerization of 1,3-butadiene (lithium or organolithium initiation in a hydrocarbon solvent) offers some advantages compared to those manufactured by other polymerization methods (e.g., it is free from metal impurities). In addition, molecular weight distributions and microstructure can easily be modifed by applying appropriate experimental conditions. In contrast with polyisoprene, where high cis content is necessary for suitable mechanical properties, these nonstereoselective but dominantly 1,4-polybutadienes are suitable for practical applications.184,482... 

There are already several excellent detailed reviews on GTP [2-5]. In this chapter I will critically analyze the existing data that strongly support a dissociative (anionic) mechanism originally proposed by R. Quirk of Akron University [6]. I will also explain how GTP can operate at 80 °C when it is well known that the classical anionic polymerization of methacrylates does not proceed above ambient temperatures. In addition, GTP will be compared to other controlled polymerization methods. 

The goal of producing low cost ( 1—5/lb.) acrylic block, comb, star, and telechelic polymers by GTP and anionic polymerization has not been met. Free radical polymerization of acrylics and other vinyl monomers on the other hand requires little purification of materials, works in water and other protic solvents, and is low cost. Considerable efforts are presently under way therefore to develop controlled free radical polymerization methods. 

Presently the main technique for the synthesis of copolymers are free-radical polymerization methods [11-17]. For a limited range of comonomers, anionic and cationic polymerizations are also used [236,237]. 

Polyphosphazene block copolymers were synthesized by these chain-growth polymerization methods. The successive anionic polymerization of N-silylphosphoranimines 19d and 19a at 133 °C yielded the block copolymer with Mw/Mn of 1.4-2.3 (Scheme 80) [278,279]. However, due to the presence of two possible leaving groups in 19d, this approach yielded block copolymers where one of the block segments contained a mixture of side groups. On the other hand, the cationic polymerization of 19b with PCI5 was carried out at ambient temperature, followed by addition of a second phosphoranimine to yield a block copolymer with Mw/Mn of 1.1-1.4, where each block segment had one kind of side chain (Scheme 81) [280]. 

Not all monomers are anionically polymerizable. Nevertheless, one can take advantage of the activity of the living ends to introduce reactive end groups at the extremity of homopolymers and then use such end groups to initiate the polymerization of anionically non polymerizable monomers. This method has been applied to the synthesis of copolymers with polyvinyl and polylactone blocks19 and of copolymers with polyvinyl and polypeptide blocks20-2S). One can at last use both anionic and cationic polymerization to prepare block copolymers of tetrahydrofuran with styrene or methylstyrene2. ... 

Macromonomer Synthesis Using Anionic Polymerization Methods... 

---