Polymer resolution

Comparison of Polymer Resolution in Thermal Field-Flow Fractionation and Size Exclusion Chromatography, J. J. Gunderson and J. C. Giddings, Anal. Chim. Acta, 189, 1 (1986). 

Gunderson, J.J. Giddings, J.C. Comparison of polymer resolution in thermal field-flow fractionation and size-exclusion chromatography. Anal. Chim. Acta 1986,189,1. 

Reports on polymer resolutions are scarce just some examples with enrichment are known. Resolution of racemic monomeric mixtures on support are examined by Prof. Selegny and Dr Lancon in the last chapter. 

TABLE 3.1 Sizes of Structural Details of Polymers, Resolutions, and Magnifications Attainable with the Different Microscopic Techniques and Scattering Methods... 

A recent design of the maximum bubble pressure instrument for measurement of dynamic surface tension allows resolution in the millisecond time frame [119, 120]. This was accomplished by increasing the system volume relative to that of the bubble and by using electric and acoustic sensors to track the bubble formation frequency. Miller and co-workers also assessed the hydrodynamic effects arising at short bubble formation times with experiments on very viscous liquids [121]. They proposed a correction procedure to improve reliability at short times. This technique is applicable to the study of surfactant and polymer adsorption from solution [101, 120]. 

Fig. VIII-10. (a) Intensity versus energy of scattered electron (inset shows LEED pattern) for a Rh(lll) surface covered with a monolayer of ethylidyne (CCH3), the structure of chemisorbed ethylene, (b) Auger electron spectrum, (c) High-resolution electron energy loss spectrum. [Reprinted with permission from G. A. Somoijai and B. E. Bent, Prog. Colloid Polym. ScL, 70, 38 (1985) (Ref. 6). Copyright 1985, Pergamon Press.]...

Other than the obvious advantages of reduced fluorescence and high resolution, FT Raman is fast, safe and requires mmimal skill, making it a popular analytic tool for the characterization of organic compounds, polymers, inorganic materials and surfaces and has been employed in many biological applications [41]. 

Krausch G, Hipp M, Bditau M, Mlynek J and Marti O 1995 High resolution imaging of polymer surfaces with chemical sensitivity Macromolecules 28 260... 

One interesting new field in the area of optical spectroscopy is near-field scaiming optical microscopy, a teclmique that allows for the imaging of surfaces down to sub-micron resolution and for the detection and characterization of single molecules [, M]- Wlien applied to the study of surfaces, this approach is capable of identifying individual adsorbates, as in the case of oxazine molecules dispersed on a polymer film, illustrated in figure Bl.22,11 [82], Absorption and emission spectra of individual molecules can be obtamed with this teclmique as well, and time-dependent measurements can be used to follow the dynamics of surface processes. 

In each of these approaches, imaging is confined to the top of a single polymeric film by adjusting optical absorption. The penetration depth of the silylation agent and the attendant swelling of the polymer film must also be controlled to avoid distortion of the silylated image. Resists of this type are capable of very high resolution (Fig. 37). 

G. Beamson and D. Briggs, High Resolution XPS of Organic Polymers,]ohxi Wiley Sons, Inc., New York, 1992. 

The incidence of these defects is best determined by high resolution F nmr (111,112) infrared (113) and laser mass spectrometry (114) are alternative methods. Typical commercial polymers show 3—6 mol % defect content. Polymerization methods have a particularly strong effect on the sequence of these defects. In contrast to suspension polymerized PVDF, emulsion polymerized PVDF forms a higher fraction of head-to-head defects that are not followed by tail-to-tail addition (115,116). Crystallinity and other properties of PVDF or copolymers of VDF are influenced by these defect stmctures (117). 

Raman Microspectroscopy. Raman spectra of small soflds or small regions of soflds can be obtained at a spatial resolution of about 1 p.m usiag a Raman microprobe. A widespread appHcation is ia the characterization of materials. For example, the Raman microprobe is used to measure lattice strain ia semiconductors (30) and polymers (31,32), and to identify graphitic regions ia diamond films (33). The microprobe has long been employed to identify fluid iaclusions ia minerals (34), and is iacreasiagly popular for identification of iaclusions ia glass (qv) (35). 

R. Komoroski, ed.. High Resolution NMR Spectroscopy of Synthetic Polymers in Bulk, VCH Pubhshers, New York, 1986. 

Commercially available photon tunneling microscopes have a lateral resolution of 160 nm but subnanometer vertical resolution. The nondestmctive, instantaneous 3-D viewing of a surface (no scanning) yields real-time imaging as one traverses a given sample. The sample must be a dielectric, but transparent polymer tepHcas of opaque samples can be studied. 

Profilometry of softer materials, such as polymers, is also possible with SFM, and with STM if the sample is conducting. Low forces on the SFM tip allow imaging of materials whose surfaces are degraded by traditional stylus profilometry. However, when the surface is soft enough that it deforms under pressure from the SFM tip, resolution will be degraded and topography may not be representative of the true... 

---