Poly graft copolymers

Figure 9.17 Plot of log [i ]M versus retention volume for various polymers, showing how different systems are represented by a single calibration curve when data are represented in this manner. The polymers used include linear and branched polystyrene, poly(methyl methacrylate), poly(vinyl chloride), poly(phenyl siloxane), polybutadiene, and branched, block, and graft copolymers of styrene and methyl methacrylate. [From Z. Grubisec, P. Rempp, and H. Benoit, Polym. Lett. 5 753 (1967), used with permission of Wiley.]...

In addition to providing fully alkyl/aryl-substituted polyphosphasenes, the versatility of the process in Figure 2 has allowed the preparation of various functionalized polymers and copolymers. Thus the monomer (10) can be derivatized via deprotonation—substitution, when a P-methyl (or P—CH2—) group is present, to provide new phosphoranimines some of which, in turn, serve as precursors to new polymers (64). In the same vein, polymers containing a P—CH group, for example, poly(methylphenylphosphazene), can also be derivatized by deprotonation—substitution reactions without chain scission. This has produced a number of functionalized polymers (64,71—73), including water-soluble carboxylate salts (11), as well as graft copolymers with styrene (74) and with dimethylsiloxane (12) (75). 

Although they lack commercial importance, many other poly(vinyl acetal)s have been synthesized. These include acetals made from vinyl acetate copolymerized with ethylene (43—46), propjiene (47), isobutjiene (47), acrylonitrile (48), acrolein (49), acrylates (50,47), aHyl ether (51), divinyl ether (52), maleates (53,54), vinyl chloride (55), diaHyl phthalate (56), and starch (graft copolymer) (47). 

In the suspension polymerization of PVC, droplets of monomer 30—150 p.m in diameter are dispersed in water by agitation. A thin membrane is formed at the water—monomer interface by dispersants such as poly(vinyl alcohol) or methyl cellulose. This membrane, isolated by dissolving the PVC in tetrahydrofuran and measured at 0.01—0.02-p.m thick, has been found to be a graft copolymer of polyvinyl chloride and poly(vinyl alcohol) (4,5). Early in the polymerization, particles of PVC deposit onto the membrane from both the monomer and the water sides, forming a skin 0.5—5-p.m thick that can be observed on grains sectioned after polymerization (4,6). Primary particles, 1 p.m in diameter, deposit onto the membrane from the monomer side (Pig. 1), whereas water-phase polymer, 0.1 p.m in diameter, deposits onto the skin from the water side of the membrane (Pig. 2) (4). These domain-sized water-phase particles may be one source of the observed domain stmcture (7). 

MMA and DMAPMA poly(MMA-co-DMAPMA) 23, obtained by radical copolymerization, can produce a photografting reaction with acrylonitrile (AN) using BP as the initiator [61]. The formation of a graft copolymer, poly[(MMA -c<7-DMAPMA)- -AN] was confirmed by FT-IR spectrophotometry. Based on ESR studies and end group analysis, the mechanism of grafting reaction is proposed as follows ... 

Park et al. [20] reported on the synthesis of poly-(chloroprene-co-isobutyl methacrylate) and its compati-bilizing effect in immiscible polychloroprene-poly(iso-butyl methacrylate) blends. A copolymer of chloroprene rubber (CR) and isobutyl methacrylate (iBMA) poly[CP-Co-(BMA)] and a graft copolymer of iBMA and poly-chloroprene [poly(CR-g-iBMA)] were prepared for comparison. Blends of CR and PiBMA are prepared by the solution casting technique using THF as the solvent. The morphology and glass-transition temperature behavior indicated that the blend is an immiscible one. It was found that both the copolymers can improve the miscibility, but the efficiency is higher in poly(CR-Co-iBMA) than in poly(CR-g-iBMA),... 

Compatibilization along with dynamic vulcanization techniques have been used in thermoplastic elastomer blends of poly(butylene terephthalate) and ethylene propylene diene rubber by Moffett and Dekkers [28]. In situ formation of graft copolymer can be obtained by the use of suitably functionalized rubbers. By the usage of conventional vulcanizing agents for EPDM, the dynamic vulcanization of the blend can be achieved. The optimum effect of compatibilization along with dynamic vulcanization can be obtained only when the compatibilization is done before the rubber phase is dispersed. 

The structure-property relationship of graft copolymers based on an elastomeric backbone poly(ethyl acry-late)-g-polystyrene was studied by Peiffer and Rabeony [321. The copolymer was prepared by the free radical polymerization technique and, it was found that the improvement in properties depends upon factors such as the number of grafts/chain, graft molecular weight, etc. It was shown that mutually grafted copolymers produce a variety of compatibilized ternary component blends. 

Problem 31.7 1 Irradiation of poly(-l,3-butadiene), followed by addition of styrene, yields a graft copolymer that is used to make rubber soles for shoes. Draw the structure of a representative segment of this styrene-butadiene graft copolymer. 

By this method graft copolymers of PAN with poly(methyl acrylate) (PM A), poly-(butyl acrylate) (PBA), poly(acrylic acid) (PAA), poly(methyl vinylpyridine) (PMCP), and polystyrene (PSI) have been obtained. 

Poly (ary lene ether sulfone)s and poly(arylene ether ketone) have been employed to prepare block and graft copolymers. Generally, the block copolymers can be prepared by reacting functional-group-terminated oligomers with other functional oligomers and monomers. 

Very few graft copolymers based on poly(arylene ether)s have been synthesized, probably because of their chemical inertness. Klapper et al. reported grafting the polystyrene or polyisoprene onto the poly(ether ether ketone ketone) (PEEKK) by anionic deactivation.229 The carbonyl groups on tire backbone can be attacked by the polystyrene monoanion or polyisoprene anion (Mn about 3000). Due to the steric hindrance only about 30% of tire carbonyl groups can be reacted. 

---