Plasticization degree

Depending on plasticity degree a polymers behavior in impact tests is described by either the Eq. (10.21) or the Eq. (10.22). Let us note, that the Eq. (10.21) was derived from the conditions of elastic energy in sample accumulation and dissipation and therefore, fracture process itself in the obvious form (i.e., new surfaces formation) is not taken into consideration at the derivation [23]. The Eq. (10.22) was obtained from the modified energetic Griffith criterion, in which a new surfaces formation at crack If ont advancement is directly taken into consideration [22]. At such treatment it is supposed, that crack edges are absolutely flat, though experimental observations... 

Resin Viscosity. The flow properties of uncured compounded plastics is affected by the particle loading, shape, and degree of dispersion. Flow decreases with increased sphericity and degree of dispersion, but increases with increased loading. Fillers with active surfaces can provide thixotropy to filled materials by forming internal network stmctures which hold the polymers at low stress. 

Addition of approximately 40% of the halogen flame retardants are needed to obtain a reasonable degree of flame retardancy. This usually adversely affects the properties of the plastic. The efficiency of the halogens is enhanced by the addition of inorganic flame retardants, resulting ia the overall reduction of flame-retardant additive package and minimising the adverse effects of the retardants. 

In 1992 the price of alumina trihydtate varied from 0.25—1.35/kg. Alumina trihydtate is the least expensive and least effective of the flame retarders. It is only about one-fourth to one-half as effective as the halogens. Usually about 50—60% of alumina trihydtate is needed to obtain some acceptable degree of flame retardancy. It is also limited to plastics that ate not processed higher than 220°C. 

Electrical Properties. Poly(methyl methacrylate) has specific electrical properties that make it unique (Table 4). The surface resistivity of poly(methyl methacrylate) is higher than that of most plastic materials. Weathering and moisture affect poly(methyl methacrylate) only to a minor degree. High resistance and nontracking characteristics have resulted in its use in high voltage appHcations, and its excellent weather resistance has promoted the use of poly(methyl methacrylates) for outdoor electrical appHcations (22). 

Physical Properties. LLDPE is a sernicrystaUine plastic whose chains contain long blocks of ethylene units that crystallize in the same fashion as paraffin waxes or HDPE. The degree of LLDPE crystallinity depends primarily on the a-olefin content in the copolymer (the branching degree of a resin) and is usually below 40—45%. The principal crystalline form of LLDPE is orthorhombic (the same as in HDPE) the cell parameters of nonbranched PE are a = 0.740 nm, b = 0.493 nm, and c (the direction of polymer chains) = 0.2534 nm. Introduction of branching into PE molecules expands the cell slightly thus a increases to 0.77 nm and b to around 0.50 nm. 

Bags of various constmctions are used in the storage and transportation of dry chemicals. The choice of which type of bag to use should be based on the needs of the product for adequate protection and the requirements of the distribution network. To a certain degree, bags can be custom-made for a particular product indeed, almost any shipping requirement can be satisfied by one of many combinations of paper, plastic, and natural fibers incorporated in the design of bags. 

Nylon. The high degree of crystallinity in nylon means that plasticization can occur only at very low levels. Plasticizers are used in nylon but are usually sulfonamide based since these are generally more compatible than phthalates. DEHP is 25 phr compatible other phthalates less so. Sulfonamides are compatible up to 50 phr. 

Similarly, the random introduction by copolymerization of stericaHy incompatible repeating unit B into chains of crystalline A reduces the crystalline melting point and degree of crystallinity. If is reduced to T, crystals cannot form. Isotactic polypropylene and linear polyethylene homopolymers are each highly crystalline plastics. However, a random 65% ethylene—35% propylene copolymer of the two, poly(ethylene- (9-prop5lene) is a completely amorphous ethylene—propylene mbber (EPR). On the other hand, block copolymers of the two, poly(ethylene- -prop5iene) of the same overall composition, are highly crystalline. X-ray studies of these materials reveal both the polyethylene lattice and the isotactic polypropylene lattice, as the different blocks crystallize in thek own lattices. 

---