Passing inspection

Don t permit the release of incoming product until it has either passed inspection or a sample has been taken for inspection. 

Provide separate designated areas for holding product awaiting inspection, passed inspection, and failed inspection. 

Also, the facilities and sampling equipment should be sufficient to prevent cross contamination by other materials, products, and general environmental contaminates. Where possible, the sampling should be done in a quarantined area separate from other materials, especially, those that have already passed inspection. For rejected materials, procedures and facilities, i.e., storage space, to handle these materials should be in place. 

Since over 60% of all antibiotics used in Japan for veterinary purposes are tetracyclines (35), targeted surveys of tetracycline residues in animal tissues have become of particular importance for public health agencies in Japan (36, 37). In 1991, a limited survey in the Aichi prefecture of residual tetracyclines in tissues collected from 64 cattle and 68 hogs of 1358 slaughtered animals that did not pass inspection at slaughterhouses due to presence of disease symptoms was conducted (38). Among 271 kidney, liver, and other organ samples, 49 (18.1%) were positive to oxytetracycline, 5 (1.8%) to chlortetracycline, and 5 (1.8%) to doxycycline, respectively. One cattle kidney sample was positive to both oxytetracycline and doxycycline, whereas tetracycline was not detected in any of the samples. 

Company name) establishes and maintains records that give evidence that the product has passed inspection and/or test with defined acceptance criteria (see 4.16). 

The term "unusable component" that has replaced the term "unserviceable component", includes items that are in such a condition as to render them unfit for their intended purpose or for any other purpose. The unusable components may include materials or items of faulty manufacture (those that failed to pass inspection), deteriorated materials (those becoming ineffective or dangerous to handle), damaged items beyond repair (that can take place during manuf, shipping or storage), obsolescent materials (outdated, that have been replaced by newer, more effective items), captured materials and duds, which are items that have been properly initiated and failed to function, but are dangerous because they can explode any time later (Ref 9)... 

At his present assignment, Lou is waiting to obtain his next sample when he is approached by one of the concrete tmck drivers, who offers Lou 500 if he will lie and say the concrete from his tmck passes inspection. The driver tries to convince Lou that there is no way you can tell the difference between his concrete and the concrete specified by the engineer. The older man further says that this sort of thing... 

Real-World Reading Link To make sure that containers have the correct amount of fluid, some manufacturing processes use radioactivity. Particles produced by radioactive decay are detected after they pass through the containers. For instance, a half-full bottle of juice would allow too much radiation to pass through and would not pass inspection. 

Loadirig arrangement and tie-downs will have to pass inspection by a representative of the railways and sometimes by an insurance underwriter prior to shipment. 

To pass inspection and comply with the HACCP requirements in the twenty-first century, we have to change the basic concepts for surface finishing. Figure 5 shows the schematic illustration about the kinds of surface finishing performance that are assured by HACCP (HACCP surfaces). 

Not used if it fails to pass inspections or electrical tests. 

On February 26,1972, coal slurry impoundment dam 3 of the Pittston Coal Company in Logan County, West Virginia, failed, four days after it passed inspection by a federal mine inspector. In the Buffalo Creek flood that resulted, 125 people were killed. The dam, which was above dams 1 and 2, had been built on coal slurry sediment rather than on bedrock. 

B. Maintenance—Respirators that do not pass inspection must be replaced or repaired prior to use. Respirator repairs are limited to the changing of canisters, cartridges, cylinders, filters, head straps, and those items as recommended by the manufacturer. No attempt should be made to replace components or make adjustments, modifications, or repairs beyond the manufacturer s recommendations. 

Explanation Before daily use of any forklift, drivers fill out a Driver s Daily Checklist Form (Figure 9.3). If anything is wrong, broken, or unsatisfactory during the inspection, the driver must report it immediately to the supervisor. Under no circumstances should drivers operate a forklift that does not pass inspection until the supervisor clears it. 

Figure 19.3 (a) Poor conditions - inspection needed (b) passed inspection ... 

If meat passes federal inspection, an inspection stamp (Fig. M-23) is affixed to the wholesale cuts or package to eissure the retailer and consumer that the products have been inspected. Products that do not pass inspection are denatured and rendered unusable for human consumption. 

At least two more items must be considered. The process cannot be started before Safety has cleared the plant as safe for personnel and the environment. This not only means that it must be safe, but it cannot be a public nuisance for our neighbors. If the plant creates unacceptable noise levels or lighting conditions that can aggravate neighbors attempting to sleep, the plant will not pass inspection and will not be started up. 

CVSA decal issued for "Pass" inspection (no violations/defects found in items 7-20)... 

Each vehicle (motorcoach, school bus, other bus, truck, truck-tractor, semitrailer, trailer, converter dollies, etc.) used singularly or in combination may qualify for a CVSA decal if it passes inspection and a CVSA decal shall be applied. Pass Inspection , means that during a North American Standard Level I or Level V Inspection, no defects are found of the following Critical Vehicle Inspection Items ... 

Determine that the vehicle passed inspection within the last 12 months and possesses the required documentation/decal. 

The decal criteria applies only to the condition of the vehicle, not the driver. It is possible for a driver to be out-of-service and still have vehlcle(s) qualify for a decal. If each vehicle, whether used singly or in a combination, passes Inspection, a current CVSA decal shall be affixed and no other CVSA decals shall be visible. 

For more than a year thereafter the Army s standard service masks— both the M3 lightweight mask standardized earlier and its shortlived successor, the M5 combat mask—were made of neoprene. As in the case of any major change in specifications, there was an occasional hitch on the production lines. Some of these hitches were caused by the fact that batches of neoprene compound were not always uniform. A more critical problem arose when one contractor attempted to produce faceblanks for the complicated optical gas mask from neoprene. The neoprene stock refused to take molding acceptably, and nearly all the first batch of one thousand faceblanks failed to pass inspection. The contract had to be terminated. But with these exceptions, production of neoprene masks proceeded smoothly enough. 

---