Oxygen elemental analysis

Carbon Hydrogen Oxygen Elemental Analysis (% by weight) Nitrogen Phosphorus Sulfur Chlorine Ash... 

For ordinary ethoxylated surfactants, where the ethylene oxide moiety is the only source of oxygen, elemental analysis (where percent oxygen is usually determined by difference) gives an accurate value for the length of the EO chain (16). The advantage of this technique is that modem instruments for elemental analysis provide the results in a few minutes. The disadvantage—that contamination from water, alcohol, or other materials will cause inaccurate results—is the same as with the spectroscopic methods. 

J.9 You are asked to identify compound X, which was extracted from a plant seized by customs inspectors. You run a number of tests and collect the following data. Compound X is a white, crystalline solid. An aqueous solution of X turns litmus red and conducts electricity poorly, even when X is present at appreciable concentrations. When you add sodium hydroxide to the solution a reaction takes place. A solution of the products of the reaction conducts electricity well. An elemental analysis of X shows that the mass percentage composition of the compound is 26.68% C and 2.239% H, with the remainder being oxygen. A mass spectrum of X yields a molar mass of 90.0 g-moF. (a) Write the empirical formula of X. (b) Write... 

An elemental analysis of epinephrine resulted in the following composition 59.0% carbon, 26.2% oxygen, 7.15% hydrogen, and 7.65% nitrogen by mass. When 0.64 g of epinephrine was dissolved in 36.0 g of benzene, the freezing point decreased by 0.50°C. (a) Determine the empirical formula of epinephrine, (b) What is the molar mass of epinephrine ... 

Diazoalkanes are u.seful is precursors to ruthenium and osmium alkylidene porphyrin complexes, and have also been investigated in iron porphyrin chemistry. In an attempt to prepare iron porphyrin carbene complexes containing an oxygen atom on the /(-carbon atom of the carbene, the reaction of the diazoketone PhC(0)C(Ni)CH3 with Fe(TpCIPP) was undertaken. A low spin, diamagnetic carbene complex formulated as Fe(TpCIPP)(=C(CH3)C(0)Ph) was identified by U V-visible and fI NMR spectroscopy and elemental analysis. Addition of CF3CO2H to this rapidly produced the protonated N-alkyl porphyrin, and Bit oxidation in the presence of sodium dithionitc gave the iron(II) N-alkyl porphyrin, both reactions evidence for Fe-to-N migration processes. ... 

Because each chemical element is conserved, the masses of the products are equal to the masses of the elements contained in the original compound. This lets us complete the elemental analysis of the compound. The 5.00-g sample contained 4.63 g mercury and 0.37 g oxygen. The percent composition is found by dividing each elemental mass by the total mass and multiplying by 100 ... 

The number of surface atoms can be determined by chemisorption of probe molecules (H2, O2...), knowing the stoichiometry of the adsorbed species. As an example, in the case of Pt, the stoichiometry of irreversibly adsorbed hydrogen (H/Pts) and oxygen (0/Pts) at room temperature are both close to 1/1 [108-111]. Knowing the total number of atoms (elemental analysis) and the number of irreversibly adsorbed H and O, the dispersion of the particles (D = Pts/Pt) is then easily obtained. Note that the dispersion of these particles decreases when their size increases (Fig. 5). 

The chemical compositions of materials are usually expressed in terms of simple oxides calculated from elemental analysis determined by x-ray fluorescence. For spent foundry sand, the chemical parameters include bulk oxides mass composition, loss on ignition, and total oxygen demand. Table 4.6 lists the general chemical properties of spend foundry sand. It is shown that spent foundry sand consists primarily of silica dioxide. 

The material balance is consistent with the results obtained by OSA (S2+S4 in g/100 g). For oil A, the coke zone is very narrow and the coke content is very low (Table III). On the contrary, for all the other oils, the coke content reaches higher values such as 4.3 g/ 100 g (oil B), 2.3 g/ioo g (oil C), 2.5 g/ioo g (oil D), 2.4/100 g (oil E). These organic residues have been studied by infrared spectroscopy and elemental analysis to compare their compositions. The areas of the bands characteristic of C-H bands (3000-2720 cm-1), C=C bands (1820-1500 cm j have been measured. Examples of results are given in Fig. 4 and 5 for oils A and B. An increase of the temperature in the porous medium induces a decrease in the atomic H/C ratio, which is always lower than 1.1, whatever the oil (Table III). Similar values have been obtained in pyrolysis studies (4) Simultaneously to the H/C ratio decrease, the bands characteristics of CH and CH- groups progressively disappear. The absorbance of the aromatic C-n bands also decreases. This reflects the transformation by pyrolysis of the heavy residue into an aromatic product which becomes more and more condensed. Depending on the oxygen consumption at the combustion front, the atomic 0/C ratio may be comprised between 0.1 and 0.3 ... 

Fig. 9. Relationship between polarity index ((O + N)/C) and percentage of paraffinic carbon in organic sorbents from the literature. The percentage of paraffinic carbon was calculated as the product of paraffinic carbon content (0-50 ppm) from NMR distribution and percentage of carbon, nitrogen, and oxygen contents from elemental analysis.

Widespread medicinal use of colloidal bismuth subcitrate (CBS) has prompted extensive studies of bismuth compounds involving the citrate anion. Bismuth citrate is essentially insoluble in water, but a dramatic increase in solubility with increasing pH has been exploited as a bio-ready source of soluble bismuth, a material referred to as CBS. Formulation of these solutions is complicated by the variability of the bismuth anion stoichiometry, the presence of potassium and/ or ammonium cations, the susceptibility of bismuth to oxygenation to Bi=0, and the incorporation of water in isolated solids. Consequently, a variety of formulas are classified in the literature as CBS. Solids isolated from various, often ill-defined combinations of bismuth citrate, citric acid, potassium hydroxide, or ammonium hydroxide have been assigned formulas on the basis of elemental analysis data or by determination of water and ammonia content, but are of low significance in the absence of complementary data other than thermal analysis (163), infrared spectroscopy (163), or NMR spectroscopy (164). In this context, the Merck index lists the chemical formula of CBS as KgfNHJaBieOafOHMCeHsCbh in the 11th edition (165), but in the most recent edition provides a less precise name, tripotassium dicitrato bismuthate (166). 

Elemental analysis of fuel oil often plays a more major role that it may appear to do in lower-boiling products. Aromaticity (through the atomic hydrogen/carbon ratio), sulfur content, nitrogen content, oxygen content, and metals content are all important features that can influence the use of residual fuel oil. 

Trace Analysis Spectroscopic Methods for Elements. Edited by J. D.Winefordner Contamination Control in Trace Element Analysis. By Morris Zief and James W. Mitchell Analytical Applications of NMR. By D. E. Leyden and R. H. Cox Measurement of Dissolved Oxygen. By Michael L. Hitchman Analytical Laser Spectroscopy. Edited by Nicolo Omenetto... 

---