Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Thermal properties oxides

For gear trains Protection from seizing and rapid wear Extreme-pressure and anti-wear properties Resistance to oxidation Thermal stability High viscosity Low pour point Anti-foaming properties Anti-corrosion properties... [Pg.284]

The many commercially attractive properties of acetal resins are due in large part to the inherent high crystallinity of the base polymers. Values reported for percentage crystallinity (x ray, density) range from 60 to 77%. The lower values are typical of copolymer. Poly oxymethylene most commonly crystallizes in a hexagonal unit cell (9) with the polymer chains in a 9/5 helix (10,11). An orthorhombic unit cell has also been reported (9). The oxyethylene units in copolymers of trioxane and ethylene oxide can be incorporated in the crystal lattice (12). The nominal value of the melting point of homopolymer is 175°C, that of the copolymer is 165°C. Other thermal properties, which depend substantially on the crystallization or melting of the polymer, are Hsted in Table 1. See also reference 13. [Pg.56]

Sihcon dioxide layers can be formed using any of several techniques, including thermal oxidation of siUcon, wet anodization, CVD, or plasma oxidation. Thermal oxidation is the dominant procedure used in IC fabrication. The oxidation process selected depends on the thickness and properties of the desired oxide layer. Thin oxides are formed in dry oxygen, whereas thick (>0.5 jim) oxide layers are formed in a water vapor atmosphere (13). [Pg.347]

Thermal Properties. Because all limestone is converted to an oxide before fusion or melting occurs, the only melting point appHcable is that of quicklime. These values are 2570°C for CaO and 2800°C for MgO. Boiling point values for CaO are 2850°C and for MgO 3600°C. The mean specific heats for limestones and limes gradually ascend as temperatures increase from 0 to 1000°C. The ranges are as follows high calcium limestone, 0.19—0.26 dolomitic quicklime, 0.19—0.294 dolomitic limestone, 0.206—0.264 magnesium oxide, 0.199—0.303 and calcium oxide, 0.175—0.286. [Pg.166]

Table 1. Thermal Properties of Poly(Phenylene Oxides)s... Table 1. Thermal Properties of Poly(Phenylene Oxides)s...
Oxide fibers are manufactured by thermal or chemical processes into a loose wool mat, which can then be fabricated into a flexible blanket combined with binders and formed into boards, felts, and rigid shapes or fabricated into ropes, textiles and papers. The excellent thermal properties of these products make them invaluable for high temperature industrial appHcations. [Pg.53]

Over the years, GM and Ford have progressively raised their levels of demand for oxidative/thermal stability, to cater for cars with higher power and thus greater likelihood of high transmission temperatures. GM s latest designation is Dexron IID, and the latest Ford specification is M2C 33-G, commonly referred to as the Ford G fluid. The Daimler-Benz requirement is that a fluid should retain its frictional characteristics throughout its life (in other words, throughout the life of the car). Additive systems have been developed with properties acceptable to Daimler-Benz, however, and a universal ATF can now be blended. [Pg.861]

Thermoplastic xylan derivatives have been prepared by in-hne modification with propylene oxide of the xylan present in the alkaline extract of barley husks [424,425]. Following peracetylation of the hydroxypropylated xylan in formamide solution yielded the water-insoluble acetoxypropyl xylan. The thermal properties of the derivative quahfy this material as a potential biodegradable and thermoplastic additive to melt-processed plastics. Xylan from oat spelts was oxidized to 2,3-dicarboxyhc derivatives in a two-step procedure using HI04/NaC102 as oxidants [426]. [Pg.52]

Thermal treatments can be applied to modify the properties of a material, for example, dealumination and optimization of crystalHne phases. These techniques do not require oxidants. Oxidative thermal treatments are generally employed to activate molecular sieves, by removing the organic templates employed during synthesis. This is one of the key steps when preparing porous catalysts or adsorbents. In air-atmosphere calcination, the templates are typically combusted between 400... [Pg.121]

Silica is the support of choice for catalysts used in processes operated at relatively low temperatures (below about 300 °C), such as hydrogenations, polymerizations or some oxidations. Its properties, such as pore size, particle size and surface area are easy to adjust to meet the specific requirements of particular applications. Compared with alumina, silica possesses lower thermal stability, and its propensity to form volatile hydroxides in steam at elevated temperatures also limits its applicability as a support. Most silica supports are made by one of two different preparation routes sol-gel precipitation to produce silica xerogels and flame hydrolysis to give so-called fumed silica. [Pg.190]

A remaining crucial technological milestone to pass for an implanted device remains the stability of the biocatalytic fuel cell, which should be expressed in months or years rather than days or weeks. Recent reports on the use of BOD biocatalytic electrodes in serum have, for example, highlighted instabilities associated with the presence of 02, urate or metal ions [99, 100], and enzyme deactivation in its oxidized state [101]. Strategies to be considered include the use of new biocatalysts with improved thermal properties, or stability towards interferences and inhibitors, the use of nanostructured electrode surfaces and chemical coupling of films to such surfaces, to improve film stability, and the design of redox mediator libraries tailored towards both mediation and immobilization. [Pg.430]

We shall briefly discuss the electrical properties of the metal oxides. Thermal conductivity, electrical conductivity, the Seebeck effect, and the Hall effect are some of the electron transport properties of solids that characterize the nature of the charge carriers. On the basis of electrical properties, the solid materials may be classified into metals, semiconductors, and insulators as shown in Figure 2.1. The range of electronic structures of oxides is very wide and hence they can be classified into two categories, nontransition metal oxides and transition metal oxides. In nontransition metal oxides, the cation valence orbitals are of s or p type, whereas the cation valence orbitals are of d type in transition metal oxides. A useful starting point in describing the structures of the metal oxides is the ionic model.5 Ionic crystals are formed between highly electropositive... [Pg.41]

The thermal properties of C3 materials at high temperatures are most remarkable if protected from oxidation. This issue is discussed below in more detail. If they are not oxidized, the C3 materials exhibit similar stability data as ceramics [22], in particular at temperatures above 1500 K where protective coatings applied behave like a plastic and close developing surface cracks against air attack. C3 materials expose the advantages of their hierarchical structure being present in both filler and binder phase and develop wood-like properties under ambient conditions. A descriptive pa-... [Pg.258]


See other pages where Thermal properties oxides is mentioned: [Pg.244]    [Pg.235]    [Pg.384]    [Pg.506]    [Pg.321]    [Pg.66]    [Pg.161]    [Pg.65]    [Pg.563]    [Pg.46]    [Pg.399]    [Pg.595]    [Pg.20]    [Pg.180]    [Pg.383]    [Pg.198]    [Pg.102]    [Pg.587]    [Pg.205]    [Pg.121]    [Pg.258]    [Pg.258]    [Pg.21]    [Pg.96]    [Pg.289]    [Pg.844]    [Pg.152]    [Pg.427]    [Pg.66]    [Pg.233]    [Pg.249]    [Pg.107]    [Pg.131]    [Pg.179]    [Pg.96]   
See also in sourсe #XX -- [ Pg.660 ]

See also in sourсe #XX -- [ Pg.660 ]




SEARCH



Oxidation properties

Thermal oxidation

Thermal oxides

© 2024 chempedia.info