Object advantages

Jacobson94] Jacobson, I. 1994. The Object Advantage. Reading, Mass. Addison Wesley Longman. 

Jacobson, I., Ericsson, M., and Jacobson, A. (1995), The Object Advantage Business Process Reengineering with Object Technology. Addison-Wesley, Reading MA. 

In Dynamic Spatial Reconstructor at the expense of use 2D matrix of detectors there was the opportunity to use a divergent cone beam of source emission. This system had a number of lacks. In particular the number of projections is rigidly limited by the number of x-ray sources. The dispersion of source emission results in errors of data collected.. However the system confirmed basic advantages of application of conic beams and 2D matrices of detectors for collecting information about 3D object. 

For precise 3D-FEM simulations, a huge number of nodes is required (>30,000), which results in calculation times of several hours (sun spare 20) for one model. In order to decrease the number of nodes, we took advantage of the symmetry of the coils and calculated only a quarter or half of the test object. The modelled crack has a lenght of 15 mm, a height of 3 mm and is in a depth of 5 mm. The excitation frequency was 200 Hz. 

This type of coil was prepared from copper cladded printed circuit board material by applying photolithographic techniques. The p.c. board material is available with difierent copper thicknesses and with either a stiff or a flexible carrier. The flexible material offers the opportunity to adapt the planar coil to a curved three dimensional test object. In our turbine blade application this is a major advantage. The thickness of the copper layer was chosen to be 17 pm The period of the coil was 100 pm The coils were patterned by wet etching, A major advantage of this approach is the parallel processing with narrow tolerances, resulting in many identical Eddy current probes. An example of such a probe is shown in fig. 10. 

Real Time Radiography (RTR) is an advanced method of radiography in which the image is formed while the job is exposed to ionising radiation. RTR is often applied to objects on assembly lines for rapid inspection. Accept-or-reject decisions may be made immediately without the delay or expense of film development. The main advantages of RTR are thus, reduction in inspection cost and processing time. 

Computed Tomography for very large and heavy objects is a demanding challenge for the manufacturer and his subsuppliers in many respects, especially with regard to the strongest advantages of CT ... 

Another advantage with the system is that the quality of the scanning, in terms of the angle towards the weld and track partition is increased compared to manual ultrasonic testing due to the fact that the scanning technician is able to concentrate on the object rather than on the oscilloscope while scanning. 

One of the radio detection advantages is the use of decametric waves range which provide the detection and sea surface watch even via clouds, and it really does not matter from what object the detection is carried out. from the airplane, from the satellite, from the land (or vessel). 

As noted above, one of the goals of NAMD 2 is to take advantage of clusters of symmetric multiprocessor workstations and other non-uniform memory access platforms. This can be achieved in the current design by allowing multiple compute objects to run concurrently on different processors via kernel-level threads. Because compute objects interact in a controlled manner with patches, access controls need only be applied to a small number of structures such as force and energy accumulators. A shared memory environment will therefore contribute almost no parallel overhead and generate communication equal to that of a single-processor node. 

The Kohonen network or self-organizing map (SOM) was developed by Teuvo Kohonen [11]. It can be used to classify a set of input vectors according to their similarity. The result of such a network is usually a two-dimensional map. Thus, the Kohonen network is a method for projecting objects from a multidimensional space into a two-dimensional space. This projection keeps the topology of the multidimensional space, i.e., points which are close to one another in the multidimensional space are neighbors in the two-dimensional space as well. An advantage of this method is that the results of such a mapping can easily be visualized. 

The main advantage of wholesale climate control Hes in easy access to the objects, and the absence of differences in conditions between various spaces within the institution, eg, storage areas, conservation laboratories, and exhibition galleries. The actual values set for the rh are a matter of compromise metals, stone, and ceramics are best served by humidities as low as possible, but organic materials generally require higher values. An accepted... 

There are also strap-on type Brinell testers in which the anvil is supplanted by a chain or other clamping device and the indenter is spring-loaded. These have the advantage of being able to test direcdy very large objects without the need for cutting samples. 

A principal advantage of the Raman microprobe is that the optics are those of a conventional light microscope a wide variety of special-purpose objectives developed for materials and biological microscopy are available. The Raman microprobe also offers the advantage of fluorescence reduction owing to the high spatial resolution of the microscope if a region of low fluorescence can be chosen for observation. 

---