Nuclear magnetic resonance chemical stability

Hynes, M. J., EQNMR A computer program for the calculation of stability constants from nuclear magnetic resonance chemical shift data. J. Chem. Soc., Dalton Trans. 1993, 311-312. 

Bell, L.N., Bell, H.M., and Glass, T.E. 2002. Water mobility in glassy and rubbery solids as determined by oxygen-17 nuclear magnetic resonance Impact on chemical stability. Lebensm. 

A solution-state and solid-state nuclear magnetic resonance study of the complex and its separate components in both their neutral and ionized (TMP hydrochloride and SMZ sodium salt) forms was undertaken in order to elucidate the TMP-SMZ interactions. Inspection of the data for the complex in the solid state shows that the 13C chemical shifts are consistent with the ionic structure proposed by Nakai and coworkers105 (14). Stabilization of the complex is achieved by the resulting ionic interaction and by the formation of two intermolecular hydrogen bonds. 

In earlier literature reports, x-ray data of a-based ceramics, the /3-like phase observed in certain silica minerals was explained by a structural model based on disordered Q -tridymite. However, others have suggested that the structure of the stabilized jS-cristobalite-like ceramics is closer to that of a-cristobalite than that of Q -tridymite, based on the 29Si nuclear magnetic resonance (NMR) chemical shifts (Perrota et al 1989). Therefore, in the absence of ED data it is impossible to determine the microstructure of the stabilized jS-cristobalite-like phase. ED and HRTEM have provided details of the ceramic microstructure and NMR has provided information about the environments of silicon atoms in the structure. Infrared spectroscopy views the structure on a molecular level. 

Rhinebarger et al. [35] and Eyring et al. [36,37] have used lithium-7 nuclear magnetic resonance (NMR) chemical shift data to determine the stability constants for crown-ether complexes of Li+ in two IL systems consisting of 55/45 mole% N-butylpyridinium chloride-aluminum chloride and l-ethyl-3-methyl-imidazolium chloride-aluminum chloride. The stability constants for... 

Proof for the existence of benzene isomers in irradiated benzene has been obtained in several ways. These will not be discussed in detail, but they may be classified broadly as physical and chemical. Nuclear magnetic resonance has been used by Wilzbach and Kaplan to identify benzvalene.39 Prismane has also been identified by NMR and by vapor-phase chromatography. The Dewar form has been synthesized in several steps which start with ris-1,2-dihydrophthalic anhydride. Photochemically this compound yields bicyclo(2,2,0)hexa-5-ene-2,3-dicarboxylic aqid anhydride. This was followed by catalytic reduction and oxidative decarboxylation to give the Dewar form of benzene.39 The method of synthesis alone provides some basis for structure assignment but several other bits of supporting evidence were also adduced. Dewar benzene has a half-life of about 48 hr at room temperature in pyridine solution and its stability decreases rapidly as the temperature is raised. 

Properties Chemical structure solubility in water, other solvents such as ether, ethanol, acetone and buffers of different pH its isomeric nature including stereochemical configuration partition coefficient and the existence of polymorphs copies of infrared, nuclear magnetic resonance (proton and C-13), ultraviolet and mass spectra information on the chemical and physicochemical stability if relevant (e.g. formation of a hydrate, change of polymorphic form) ... 

All phases of analytical development are ideally supported by chemical separation techniques such as HPLC, TLC, GC, SFC, and CE. HPLC continues to be the primary method of analysis throughout the pharmaceutical development process. Although HPLC is limited in its ability to separate more than 15-20 components in a single analysis, and variations in columns and instrumentation manufacturer to manufacturer complicate transfer of methods, HPLC can readily be implemented to meet ICH requirements for method performance. For early-phase methods, HPLC can be coupled dynamically to mass and nuclear magnetic resonance spectrometers to facilitate the identification of unknown impurities. In later phases, HPLC can be implemented in a fully automated format as a high-throughput method for release and stability testing. 

Most of the metal alkoxides of interest for electrooptical ceramics are solids (less often liquids) that can be purified by recrystallization, sublimation, or distillation. They are all moisture sensitive, and handling under an inert atmosphere and with anhydrous solvents is thus required. Their unequivocal characterization and formulation are best achieved by x-ray diffraction studies (on monocrystals). Studies on solutions (molecular weight data, nuclear magnetic resonance, NMR, with H, or metal nuclei) are a means either to establish whether the solid-state structure is retained or, in the absence of x-ray data, to establish the molecular structure and eventually stereolability [48]. Mass spectrometry provides information on the stability of the oligomers or the het-erometallic species in the vapor phase. The information gained by infrared spectroscopy is limited the technique is mostly useful for the identification of solvates M(OR) (ROH)x (vOH absorption 3400-3100 cm-l or of chemically modified (heteroleptic) alkoxides (probe for the vCO stretching of P-diketonate or carboxylate ligands, for instance). 

---