Molybdenum characteristics

Density is a particularly important characteristic of alloys used in rotating machinery, because centrifugal stresses increase with density. Densities of the various metals in Table 1 range from 6.1 to 19.3 g/cm. Those of iron, nickel, and cobalt-base superaHoys fall in the range 7-8.5 g/cm. Those alloys which contain the heavier elements, ie, molybdenum, tantalum, or tungsten, have correspondingly high densities. 

Many types of stainless steels are available. The type most widely used in the dairy industry is 18—8 (18% chromium, 8% nickel plus iron). Small amounts of siHcon, molybdenum, manganese, carbon, sulfur, and phosphoms maybe included to obtain characteristics desired for specific appHcations. 

More recendy, molecular molybdenum-sulfur complexes and clusters have been used as soluble precursors for M0S2 in the formulation of lubricating oils for a variety of appHcations (70). Presumably, the oil-soluble molybdenum—sulfur-containing precursors decompose under shear, pressure, or temperature stress at the wear surface to give beneficial coatings. In several cases it has been shown that the soluble precursors are trifunctional in that they not only display antifriction properties, but have antiwear and antioxidant characteristics as weU. In most cases, the ligands for the Mo are of the 1,1-dithiolate type, including dithiocarbamates, dithiophosphates, and xanthates (55,71). 

Aluminide and sUicide cementation coatings such as TaAl on tantalum and MoSi2 on molybdenum oxidize at slow rates and possess some inherent self-repair characteristics. Fine cracks that appear and are common to these coatings can be tolerated because stable, protective oxides form within the cracks and seal them. Thermal cycling, however, accelerates faUure because of thermal expansion mismatch that ultimately dismpts the protective oxide coating. 

Alloying elements such as nickel, chromium, molybdenum, and copper, which may be introduced with scrap, can increase the hardenability, although only slightly, because the concentrations are ordinarily low. However, the heat-treating characteristics may change, and for appHcations in which ductihty is important, as in low carbon steels for deep drawing, the increased hardness and lower ductiHty imparted by these elements may be harmful. 

SoHd lubricants ate added to help control high friction characteristics in high speed or heavy-duty appHcations where high temperatures are generated. Molybdenum disulfide [1317-33-5] M0S2, may be used alone or in a complex compound formed by grinding with fine natural graphite, and zinc sulfide [1314-98-3] ZnS. Other compounds include calcium fluoride, cryoHte [15096-52-3] Na AlF, rare-earth oxides, and metal sulfides, eg, iron, antimony, or zinc (see LUBRICATION AND LUBRICANTS). 

Figure 4.16. Free-surface velocity profiles measured on 1400° C molybdenum. The free-surface velocity profile is characterized by an 0.05 km/s amplitude elastic precursor, a plastic wave front, and a spall signal (characteristic dip) upon unloading. The dashed lines represent the expected free surface velocity based on impedance-match calculation [Duffy and Ahrens, unpublished].

Much like the oxidation of propylene, which produces acrolein and acrylic acid, the direct oxidation of isobutylene produces methacrolein and methacrylic acid. The catalyzed oxidation reaction occurs in two steps due to the different oxidation characteristics of isobutylene (an olefin) and methacrolein (an unsaturated aldehyde). In the first step, isobutylene is oxidized to methacrolein over a molybdenum oxide-based catalyst in a temperature range of 350-400°C. Pressures are a little above atmospheric ... 

Silver-palladium-manganese brazes possess excellent creep characteristics and have been developed for high-temperature applications involving the use of cobalt or nickel-based alloys, heat-resistant steels, molybdenum and tungsten. Their liquidus temperatures lie in the range 1 100-1 250°C. 

Other ions which are reduced in the reductor to a definite lower oxidation state are those of titanium to Ti3+, chromium to Cr2+, molybdenum to Mo3+, niobium to Nb3+, and vanadium to V2 +. Uranium is reduced to a mixture of U3 + and U4+, but by bubbling a stream of air through the solution in the filter flask for a few minutes, the dirty dark-green colour changes to the bright apple-green colour characteristic of pure uranium(I V) salts. Tungsten is reduced, but not to any definite lower oxidation state. 

Fig. 1-15. The molybdenum spectrum excited by 35-kv electrons and by the polychromatic beam from a 35-kv x-ray tube. With x-ray excitation, most of the energy appears in the characteristic lines. With electron excitation, most of it is wasted in the continuous spectrum.

Glocker and Frohnmayer determined the characteristic constant c for nine elements (Reference 2, Table 4) ranging in atomic numbers from 42 (molybdenum) to 90 (thorium). They proved that identical results could be obtained with the sample in the primary (polychromatic) or in the diffracted (monochromatic) beam. The method was applied with good results to the determination of barium in glass of antimony in a silicate of hafnium in the mineral alvite and of molybdenum, antimony, barium, and lanthanum in a solution of their salts—for example, 5.45% barium was found on 90-minute exposure by the x-ray method for a glass that yielded 5.8% on being analyzed chemically. 

Consider individual atoms of an element deposited on a thin substrate highly transparent to x-rays—say atoms of molybdenum upon paper. Let a characteristic line (say molybdenum K ) be excited by a polychromatic beam, x-ray source and detector both being located above the sample. So long as the number of molybdenum atoms is small, they will not noticeably attenuate the incident beam, nor will an x-ray quantum radiated by any molybdenum atom be absorbed by any other. Under these conditions, the intensity of the characteristic line will be proportional to the number of molybdenum atoms and hence to the thickness of the molybdenum film. 

Substitution of known values in Equation 6-6 gives a lower value of a (3520 as against 4410) than that corresponding to the experimental points in Figure 6-4, which indicates that the counting rates measured for chromium Ka are higher than expected on the basis of the treatment given above. Such an increase in the intensity of this characteristic line could be due to its excitation by the characteristic lines of the substrate, notably molybdenum Ka experimental evidence for this excitation process was obtained.10... 

A choice of target materials is offered, including copper and molybdenum (as well as tungsten) for the generation of monochromatic characteristic... 

Just as, in Group VB, niobium, so, in this Group, molybdenum provides most of the examples of the chalcogenide halides. The occurrence and preparation of such compounds are described in numerous publications. In most cases, they have been obtained as powders, with the composition based on chemical analyses only. The presence of defined, homogeneous phases is, therefore, in many cases doubtful. In addition, some published results are contradictory. A decision is possible where a complete structure analysis has been made. As will be shown later, the formation of metal-metal bonds (so-called clusters), as in the case of niobium, is the most characteristic building-principle. Such clusters... 

Optimum conditions for the formation of CdS by the acidic method on metallic A1 substrate at 25 °C have been reported as follows pH 2.3, potential -1 V vs. SCE, and electrolysis time > 2 h [44]. Thermal treatment improved the characteristics of the films and their photovoltaic properties, which were evaluated by evaporating a CU2S layer on the CdS/Al film, to form a heterojunction cell. The influence of the deposition substrate on the formation and morphology of CdS was found to be important. The aluminum substrates gave the best results among Pt, Mo, and Al. In the case of molybdenum, surface blocking by adsorbed sulfur was considered. 

The similarity of the results obtained for finite elusters and the infinite slab allows to eonclude in favour of the validity of the eluster model of adequate size (6 or 8 molybdenum atoms). In addition to the chemisorption of organic molecules on solid surfaces which is generally considered as a localized phenomenon, the interaction between molybdenum oxide and an adsorbate can also be represented by a loeal eomplex formed by a finite eluster and the adsorbed molecule. Indeed, the study of the evolution of the electronic properties as a funetion of the cluster size shows that, for a eluster eontaining 6 or 8 molybdenum atoms, most of the electronic properties converge towards limit values. This eonvergence is sensitive to the direction of the cluster growth. On the other hand, the electronic properties of the (001), (010) and (100) faces are not identieal, the type of surface atoms being different these results allow to predict that the characteristics of the chemisorption step will depend on the particular face on which it takes place. 

---