Methane molecular weight

Natural gas can be assumed to be pure methane [molecular weight = 16, Cp = 36.8 J/(mol K)], and an ideal gas at the conditions being considered here. Note that the mass flow rate A/ is puA. where p is the mass density of the gas, v is the average gas velocity, and A is the area of the pipe. 

Carbon-dioxide Carbon-dioxide/methane Molecular weight Oxygen/carbon -dioxide Carbon-dioxide Physical properties Carbon -dioxide/ Methane Physical properties... 

The volume fraction would typically be used to represent the make up of a gas at a particular stage in a process line and describes gas composition e.g. 70% methane and 30% Ethane (also known as mol fractions) at a particular temperature and pressure. Gas composition may also be expressed in mass terms by multiplying the fractions by the corresponding molecular weight. 

Glycolysis is claimed to be somewhat less cosdy than methan olysis (33). Depolymerization is not taken completely to monomers (34). Rather, recovered PET is depolymerized to low molecular weight oligomers. Contaminants are removed using proprietary technology. The oligomers are then fed to a melt polymerization vessel in which PET is produced. 

In addition to these mechanical problems there are two aspects of the compression process which relate specifically to ethylene. Eirst, there is a tendency for small amounts of low molecular weight polymer to be formed and, second, the gas may decompose into carbon, hydrogen, and methane if it becomes overheated during compression. Cavities in which the gas can collect and form polymer, which hardens with time or in which the gas can become hot, need to be avoided. 

Hydrocarbons, compounds of carbon and hydrogen, are stmcturally classified as aromatic and aliphatic the latter includes alkanes (paraffins), alkenes (olefins), alkynes (acetylenes), and cycloparaffins. An example of a low molecular weight paraffin is methane [74-82-8], of an olefin, ethylene [74-85-1], of a cycloparaffin, cyclopentane [287-92-3], and of an aromatic, benzene [71-43-2]. Cmde petroleum oils [8002-05-9], which span a range of molecular weights of these compounds, excluding the very reactive olefins, have been classified according to their content as paraffinic, cycloparaffinic (naphthenic), or aromatic. The hydrocarbon class of terpenes is not discussed here. Terpenes, such as turpentine [8006-64-2] are found widely distributed in plants, and consist of repeating isoprene [78-79-5] units (see Isoprene Terpenoids). 

Coal Hquefaction iavolves raising the atomic hydrogen-to-carbon ratio from approximately 0.8/1.0 for a typical bituminous coal, to 2/1 for Hquid transportation fuels or 4/1 for methane (4). In this process, molecular weight reduction and removal of mineral matter and heteroatoms such as sulfur, oxygen, and nitrogen may need to be effected. 

By proper selection of catalyst and reaction conditions, hydrocarbons and oxygenates ranging from methane and methanol through high (> 10,000) molecular weight paraffin waxes can be synthesized as iadicated ia Figure 11 (44). 

The process gas of ethylene plants and methyl tertiary butyl ether plants is normally a hydrogen/ methane mixture. The molecular weight of the gas in such processes ranges from 3.5 to 14. The tliermodynamic behavior of hydrogen/methane mixtures has been and continues to be extensively researched. The gas dynamic design of turboexpanders, which are extensively used in such plants, depends on the equations of state of the process gas. Optimum performance of the turboexpander and associated equipment demands accurate thermodynamic properties for a wide range of process gas conditions. 

Calculate the heat generated by dissociation and formation as one molecular weight of methane, CHi, burns to carbon dioxide and water. How does this heating value compare to the tabular heating value for methane ... 

Since few chemicals (e.g. hydrogen, methane, ammonia) have a molecular weight less than that... 

On the other hand, organic materials of relatively low molecular weight such as acetylene, benzene, ethylene and methane, can produce vapour-grown carbon materials by imperfect combustion or by exposing their vapour to a heated substrate in an electric furnace in the presence of a metal catalyst. The latter process generates VGCFs. Other precursors to VGCF include polyacrylonitrile (PAN), isotropic or mesophase pitch, rayon or nylon [8]. 

The use of the K-factor charts represents pure components and pseudo binary systems of a light hydrocarbon plus a calculated pseudo heavy component in a mixture, when several components are present. It is necessary to determine the average molecular weight of the system on a methane-free basis, and then interpolate the K-value between the two binarys whose heavy component lies on either side of the pseudo-components. If nitrogen is present by more than 3-5 mol%, the accuracy becomes poor. See Reference 79 to obtain more detailed explanation and a more complete set of charts. 

Higher molecular weight hydrocarbons present in natural gases are important fuels as well as chemical feedstocks and are normally recovered as natural gas liquids. For example, ethane may be separated for use as a feedstock for steam cracking for the production of ethylene. Propane and butane are recovered from natural gas and sold as liquefied petroleum gas (LPG). Before natural gas is used it must be processed or treated to remove the impurities and to recover the heavier hydrocarbons (heavier than methane). The 1998 U.S. gas consumption was approximately 22.5 trillion ft. ... 

As the molecular weight of the hydrocarbon increases (lower H/C feed ratio), the H2/CO product ratio decreases. The H2/CO product ratio is approximately 3 for methane, 2.5 for ethane, 2.1 for heptane, and less than 2 for heavier hydrocarbons. Noncatalytic partial oxidation of hydrocarbons is also used to produce synthesis gas, but the H2/CO ratio is lower than from steam reforming ... 

---