Methacrylic acid, copolymerization

Emulsion breakers are made from acrylic acid or methacrylic acid copolymerized with hydrophilic monomers [148]. The acid groups of acrylic acid and methacrylic acid are oxalkylated by a mixture of polyglycols and polyglycol ethers to provide free hydroxy groups on the molecule. The copolymers are made by a conventional method, for example, by free radical copolymerization in solution, emulsion, or suspension. The oxalkylation is performed in the presence of an acid catalyst, the acid being neutralized by an amine when the reaction is complete. 

Poly (Vinyl Acetate-co-Methacrylic acid) copolymeric microspheres crosslinked with N, N -methylene bisacrylamide have been prepared by free radical emulsion polymerization. The microspheres have been characterized by differential scanning calorimetry (DSC) and x-ray diffractometry (X-RD) to understand about the drag dispersion in microspheres. Scanning electron microscopy (SEM) was used to assess the surface morphology of particles prepared, and observe the spherical nature... 

VP copolymerization piNYL POLYTffiRS - N-VINYLAMIDE POLYTffiRS] pol 24) Methacrylic acid [71-49-4]... 

Butadiene—Methacrylic Acid Ionomers. Carboxyl groups can readily be introduced into butadiene elastomers by copolymerization, and the effects of partial neutralization have been reported (63—66). The ionized polymers exhibit some degree of fluidity at elevated temperatures, but are not thermoplastic elastomers, and are very deficient in key elastomer properties such as compression set resistance. 

Developments in aliphatic isocyanates include the synthesis of polymeric aliphatic isocyanates and masked or blocked diisocyanates for appflcafions in which volatility or reactivity ate of concern. Polymeric aliphatic isocyanates ate made by copolymerizing methacrylic acid derivatives, such as 2-isocyanatoethyl methacrylate, and styrene [100-42-5] (100). Blocked isocyanates ate prepared via the reaction of the isocyanate with an active hydrogen compound, such as S-caprolactam, phenol [108-95-2] or acetone oxime. 

Acrylic Polymers. Although considerable information on the plasticization of acryUc resins is scattered throughout journal and patent hterature, the subject is compHcated by the fact that acryUc resins constitute a large family of polymers rather than a single polymeric species. An infinite variation in physical properties may be obtained through copolymerization of two or more acryUc monomers selected from the available esters of acryUc and methacryhc acid (30) (see Acrylic esterpolya rs Methacrylic acid and derivatives). 

Secondary Bonding. The atoms in a polymer molecule are held together by primary covalent bonds. Linear and branched chains are held together by secondary bonds hydrogen bonds, dipole interactions, and dispersion or van der Waal s forces. By copolymerization with minor amounts of acryhc (CH2=CHCOOH) or methacrylic acid followed by neutralization, ionic bonding can also be introduced between chains. Such polymers are known as ionomers (qv). 

Pure polymeric acrylonitrile is not an interesting fiber and it is virtually undyeable. In order to make fibers of commercial iaterest acrylonitrile is copolymerized with other monomers such as methacrylic acid, methyl methacrylate, vinyl compounds, etc, to improve mechanical, stmctural, and dyeing properties. Eibers based on at least 85% of acrylonitrile monomer are termed acryHc fibers those containing between 35—85% acrylonitrile monomer, modacryhc fibers. The two types are in general dyed the same, although the type and number of dye sites generated by the fiber manufacturing process have an influence (see Eibers, acrylic). 

A waterborne system for container coatings was developed based on a graft copolymerization of an advanced epoxy resin and an acryHc (52). The acryhc-vinyl monomers are grafted onto preformed epoxy resins in the presence of a free-radical initiator grafting occurs mainly at the methylene group of the aHphatic backbone on the epoxy resin. The polymeric product is a mixture of methacrylic acid—styrene copolymer, soHd epoxy resin, and graft copolymer of the unsaturated monomers onto the epoxy resin backbone. It is dispersible in water upon neutralization with an amine before cure with an amino—formaldehyde resin. 

The amount of polar monomer one would copolymerize with the alkyl acrylate monomer(s) very much depends on the type of polar monomer and the desired change in rheological properties one would like to achieve. Strong hydrogen bonding monomers, such as acrylic acid, methacrylic acid, acrylamide, or methacrylamide are typically used at levels of 12% or less of the total monomers. 

Hybrid systems of acrylics with other technologies have been reported. Aciylic and epoxy polymers can be coupled through the use of 2-methacryloloxyethyl phosphate. The phosphoric acid functionality reacts with epoxy and the methacrylate group copolymerizes with the acrylic backbone [ 145] (Scheme 14). 

Copolymerization of methacrylic acid with butadiene and isoprene was photoinitiated by Mn2(CO)io without any halide catalyst [28,29]. The po]ymerization system is accompanied by a Dieis-Alder additive. Cross propagation reaction was promoted by adding trieth-y]aluminum chioride. 

During mutual graft copolymerization, homopolymerization always occurs. This is one of the most important problems associated with this technique. When this technique is applied to radiation-sensitive monomers such as acrylic acid, methacrylic acid, polyfunctional acrylates, and their esters, homopolymer is formed more rapidly than the graft. With the low-molecular weight acrylate esters, particularly ethyl acrylate, the homopolymer problem is evidenced not so much by high yields as by erratic and irreproducible grafting. 

Fig. 137.—Equilibrium swelling ratio qm of poly-(methacrylic acid) gels prepared by copolymerizing methacrylic acid with 1, 2, and 4 percent (upper, middle, and lower curves, respectively) of divinylbenzene plotted against degree of neutralization i with sodium hydroxide. (Katchalsky, Lifson, and Eisenberg. )...

Free-radical multicomponent copolymerization of dialkylstannyl maleates or dialkylstannyl dimethacrylates with methallyl alcohol (or (J-hydroxyalkyl acrylates) and vinyl monomers (sryrene, methacrylic acid or methacrylamide) yields polymeric powders. Due to their storage and thermal stability and impact strength they are used as protective coatings 79). 

The effect of hydrophobicity of the polymer on the permeability of poly(2-hydroxyethyl methacrylate (HEMA)-co-methacrylic acid (MAAc) hydrogels was studied [12], The hydrophobicity was controlled by copolymerization with butyl methacrylate (BMA). The dependence of permeability on pH increased as the hydrophobicity increased even though the rate of diffusion decreased. Cross-link density of the hydrogel also contributed to pH-dependent permeability. 

Ionomers are made in a two-stage process. In the first step, we copolymerize ethylene with small amounts of an organic acid containing a vinyl group, such as acrylic or methacrylic acid, in a high pressure reactor. In the second step, we neutralize the acid comonomers to form metal salts. We can create ionomers with a variety of metal salts, including sodium, calcium, and zinc. 

Ionomer-type elastomers, containing small amounts (less than 5%) of metal carboxylate or sulfonate groups, have potential as a new class of thermoplastic elastomers. Carboxylic acid groups are introduced into polymers such as polybutadiene by copolymerization with a monomer such as acrylic or methacrylic acid. 

Acrylic resins are generally well characterized by Py-GC/MS without the need for any derivatization reaction. However, in waterborne polymer dispersions it is common to have minor amounts of acrylic and/or methacrylic acid monomers added in the copolymerization to help the stability of the final latex. These monomers can also appear in the pyrolysis products, and it has been shown that with on-line derivatization they can be more efficiently revealed [85]. 

For the first time attention to the highly important role played by the thermodynamic factors in the formation of macromolecules during copolymerization was drawn almost a quarter of a century ago [52], When investigating the copolymerization of styrene with methacrylic acid in a solution of CCI4 and in a solution of dioxane in the region of low conversions, the authors established that copolymers with the same composition had an identical microstructure regardless of the solvent type and of the monomer molar ratio... 

Vinyl groups of 1,4-DVB microgels have been converted to carboxylic acid groups by ozone [291]. After modification the microgels could be dissolved in methanol. About 83 % of the vinyl groups could be converted. A simpler way to prepare microgels with carboxyl acid groups at their surface is the copolymerization of DVB with methacrylic acid in an aqueous emulsion [292]. 

Fig. 56. Dependence of Mwof the microgels on the polymer yield in the anionic polymerization of EDMA in toluene by n-BuLi [254] (see Figure 53 caption for the reaction conditions). Reduced viscosity vs concentration of microgels a) Composition (mol %) N,N -methyl-enebisacrylamide (55%), methacrylamide (33%), methacrylic acid (2%), methacrylamido acetaldehyd-dimethylacetal (10%),measured at 20 °C in water, b) Composition (mol %) 1,4-DVB (35%), propenic acid amide-2-methyl-N-(4-methyl-2-butyl-l,3-dioxolane prepared by emulsion copolymerization and measured in dimethylformamide.

Crosslinked polymer particles with a rather complex structure, which have also been designated by the name microgels and recommended as components of metal effect paints, consist of carboxyl-terminated oligoesters of 12-hydroxy stearic acid which were reacted with glycidyl methacrylate, subsequently copolymerized with MMA and hydroxymethyl methacrylate and then crosslinked by hydroxy melamine [346]. 

---