Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Metal oxide stability

Some higher alcohols (10 wt %) are present and it is proposed that the basic metal oxide stabilizes oxygenated species involved in the C—C bond formation. Similar results have been obtained with LaTii. Cu Os [8-11] with a deeper characterization of the catalysts. For x = 0.5 or 0.6, the selectivity to methanol is between 78 and 83% with a drastic increase of CO hydrogenation by increasing Cu substitution (maximum of activity for x = 0.6). The understanding of the catalytic behavior has been facilitated by the comparison of the main catalysts characteristics before and after reactivity test. By XRD, LaTh. Cu Os perovskite structure appears stable for 0.3 copper from the perovskite. Results are similar for LaMni- cCu cOs [8,9]. However, in both cases, no further study has been made to know the real value of x in the remaining perovskite. [Pg.634]

Relatively high levels of insoluble iron(III) and manganese(IV) frequently are found in water as colloidal material, which is difficult to remove. These metals can be associated with humic colloids or peptizing organic material that binds to colloidal metal oxides, stabilizing the colloid. [Pg.127]

L. Qiu, D.A. Guzonas, Prediction of metal oxide stability in supercritical water reactors —Pourbaix versus Elhngham, in The 3rd Canada-China Joint Workshop on Supercritical Water-Cooled Reactors (CCSC-2012), Xian, China, April 25—28, 2012. [Pg.144]

The oxide is soluble in ammonia to give the complex [AglNHjlj] (linear). On heating, silver(I) oxide loses oxygen to give the metal (all the coinage metal oxides have low thermal stability and this falls in the order Cu > Ag > Au). [Pg.427]

FWWMR Finish. The abbreviation for fire, water, weather, and mildew resistance, FWWMR, has been used to describe treatment with a chlorinated organic metal oxide. Plasticizers, coloring pigments, fiUers, stabilizers, or fungicides usuaUy are added. However, hand, drape, flexibUity, and color of the fabric are more affected by this type of finish than by other flame retardants. Add-ons of up to 60% are required in many cases to obtain... [Pg.486]

The result is the formation of a dense and uniform metal oxide layer in which the deposition rate is controlled by the diffusion rate of ionic species and the concentration of electronic charge carriers. This procedure is used to fabricate the thin layer of soHd electrolyte (yttria-stabilized 2irconia) and the interconnection (Mg-doped lanthanum chromite). [Pg.581]

The performance of many metal-ion catalysts can be enhanced by doping with cesium compounds. This is a result both of the low ionization potential of cesium and its abiUty to stabilize high oxidation states of transition-metal oxo anions (50). Catalyst doping is one of the principal commercial uses of cesium. Cesium is a more powerflil oxidant than potassium, which it can replace. The amount of replacement is often a matter of economic benefit. Cesium-doped catalysts are used for the production of styrene monomer from ethyl benzene at metal oxide contacts or from toluene and methanol as Cs-exchanged zeofltes ethylene oxide ammonoxidation, acrolein (methacrolein) acryflc acid (methacrylic acid) methyl methacrylate monomer methanol phthahc anhydride anthraquinone various olefins chlorinations in low pressure ammonia synthesis and in the conversion of SO2 to SO in sulfuric acid production. [Pg.378]

Acid acceptor. This is the main function of metal oxides in CR adhesive formulations. Upon age, small amounts of hydrochloric acid are released which may cause discolouration and substrate degradation. Magnesium oxide (4 phr) and zinc oxide (5 phr) act synergistically in the stabilization of solvent-borne polychloroprene adhesives against dehydrochlorination. [Pg.661]

Fillers can also be used to promote or enhance the thermal stability of the silicone adhesive. Normal silicone systems can withstand exposure to temperatures of 200 C for long hours without degradation. However, in some applications the silicone must withstand exposure to temperatures of 280 C. This can be achieved by adding thermal stabilizers to the adhesive formulations. These are mainly composed of metal oxides such as iron oxide and cerium oxide, copper organic complexes, or carbon black. The mechanisms by which the thermal stabilization occurs are discussed in terms of radical chemistry. [Pg.692]

Bismuth oeeurs mainly as bismite (a-Bi203), bismuthinite (Bi2S3) and bismutite [(Bi0)2C03] very oeeasionally it oeeurs native, in assoeiation with Pb, Ag or Co ores. The main eommereial souree of the element is as a byproduet from Pb/Zn and Cu plants, from whieh it is obtained by special processes dependent on the nature of the main product. Sulfide ores are roasted to the oxide and then reduced by iron or charcoal. Because of its low mp, very low solubiUty in Fe, and fairly high oxidative stability in air, Bi can be melted and cast (like Pb) in iron and steel vessels. Like Sb, the metal is too brittle to roll, draw, or extrude at room temperature, but above 225°C Bi can be worked quite well. [Pg.550]

Steam-turbine lubricants Lubricants in steam turbines are not exposed to such arduous conditions as those in engines. The main requirement is for high oxidation stability. However, they may be exposed to aqueous condensate or, in the case of marine installations, to sea water contamination, so they have to be able to separate from water easily and to form a rustpreventing film on ferrous surfaces, and it is usual to employ rust inhibitors. The problem of tin oxide formation on white-metal bearings is associated with the presence of electrically conducting water in lubricants and can be over-come by keeping the lubricant dry . [Pg.452]

The overall pattern of behaviour of titanium in aqueous environments is perhaps best understood by consideration of the electrochemical characteristics of the metal/oxide and oxide-electrolyte system. The thermodynamic stability of oxides is dependent upon the electrical potential between the metal and the solution and the pH (see Section 1.4). The Ti/HjO system has been considered by Pourbaix". The thermodynamic stability of an... [Pg.867]

Since does not take part in the reaction, the boundary line between M and MO is independent of logPsoj d so given by a straight vertical line at logPo2 = 16, parallel to the -axis (line 1 in Fig. 7.67). It should be noticed that stability areas across the boundary follow the sequence of condensed phases shown in the equation, i.e. on the left-hand side of the boundary pure metal is the stable phase and on the right-hand side the pure metal oxide. [Pg.1116]

Before considering the principles of this method, it is useful to distinguish between anodic protection and cathodic protection (when the latter is produced by an external e.m.f.). Both these techniques, which may be used to reduce the corrosion of metals in contact with electrolytes, depend upon the electrochemical mechanisms that result from changing the potential of a metal. The appropriate potential-pH diagram for the Fe-H20 system (Section 1.4) indicates the magnitude and direction of the changes in the potential of iron immersed in water (pH about 7) necessary to make it either passive or immune in the former case the stability of the metal depends on the formation of a protective film of metal oxide (passivation), whereas in the latter the metal itself is thermodynamically stable and egress of metal ions from the lattice into the solution is thus prevented. [Pg.261]

Addition of metallic oxides to isobutene polymerized by high energy radiation leads to a spectacular increase in the yield.313. It seems that some ions are stabilized by complexing with the surface of the oxide and such an interaction prevents their recombination with the gegen-ions. These observations confirm therefore the suggested cause of inefficient ionic polymerization in systems exposed to ionizing radiation. [Pg.157]

The Structural Stability of Transition Metal Oxide Insertion Electrodes for Lithium Batteries... [Pg.293]

This review focuses on the structural stability of transition metal oxides to lithium insertion/extraction rather than on their electrochemical performance. The reader should refer to cited publications to access relevant electrochemical data. Because of the vast number of papers on lithium metal oxides that have been published since the 1970s, only a selected list of references has been provided. [Pg.295]


See other pages where Metal oxide stability is mentioned: [Pg.489]    [Pg.489]    [Pg.294]    [Pg.145]    [Pg.806]    [Pg.489]    [Pg.930]    [Pg.17]    [Pg.966]    [Pg.489]    [Pg.489]    [Pg.294]    [Pg.145]    [Pg.806]    [Pg.489]    [Pg.930]    [Pg.17]    [Pg.966]    [Pg.173]    [Pg.389]    [Pg.283]    [Pg.550]    [Pg.265]    [Pg.512]    [Pg.344]    [Pg.253]    [Pg.164]    [Pg.438]    [Pg.233]    [Pg.74]    [Pg.503]    [Pg.256]    [Pg.334]    [Pg.772]    [Pg.896]    [Pg.134]    [Pg.1097]    [Pg.1116]    [Pg.1129]    [Pg.294]   
See also in sourсe #XX -- [ Pg.50 , Pg.53 , Pg.58 , Pg.198 ]




SEARCH



Approaches to the Improvement of Metal Oxide Structure Stability

Electrostatic stabilization, metal oxide

Instability of Metal Oxide Parameters and Approaches to Their Stabilization

Metal oxide solid electrolytes yttria-stabilized zirconia

Metal oxide-based compounds thermal stability

Metallic stabilizers

Metals stabilization

OXIDATION OXIDATIVE STABILITY

Oxidative stability

Oxidative stabilizers

Stability of Bulk Metal Oxides

Stability of metal oxides

Stability oxides

Stability transition metal oxide insertion

Stabilization of unstable d-metal oxidation

Stabilization of unstable d-metal oxidation states

Stabilization of unstable d-metal oxidation states by complex formation

The Morphological Stability of Boundaries During Metal Oxidation

© 2024 chempedia.info