Materials polymerization Laser

B. Synthesis of Polymeric Materials by Laser Vaporizatioii - Induced Polymerization... 

Hoyle, C. E. and J. F. Kinstle (eds.), Radiation Curing of Polymeric Materials , ACS, Washington, DC, 1990. Developments in cationic polymerization, laser-initiated polymerization and high energy radiation curing are discussed. 

Gardella, J.A., Graham, S.W., Hercules, D.M., in E.D. Carver (Ed.), Structural Characterization of Polymeric Materials by Laser Desorption Mass Spectrometry. Advances in Chemistry Series 303, American Chemical Society, Washington DC, 1983, p. 635. 

Starting from 27, cyclo-Cig was prepared in the gas phase by laser flash heating and the neutral product, formed by stepwise elimination of three anthracene molecules in retro-Diels-Alder reactions, was detected by resonant two-photon-ionization time-of-flight mass spectrometry [23]. However, all attempts to prepare macroscopic quantities of the cyclocarbon by flash vacuum pyrolysis using solvent-assisted sublimation [50] only afforded anthracene and polymeric material. 

Hiroshi Fukumura received his M.Sc and Ph.D. degrees from Tohoku University, Japan. He studied biocompatibility of polymers in the Government Industrial Research Institute of Osaka from 1983 to 1988. He became an assistant professor at Kyoto Institute of Technology in 1988, and then moved to the Department of Applied Physics, Osaka University in 1991, where he worked on the mechanism of laser ablation and laser molecular implantation. Since 1998, he is a professor in the Department of Chemistry at Tohoku University. He received the Award of the Japanese Photochemistry Association in 2000, and the Award for Creative Work from The Chemical Society Japan in 2005. His main research interest is the physical chemistry of organic molecules including polymeric materials studied with various kinds of time-resolved techniques and scanning probe microscopes. 

Alternative approaches consist in heat extraction by means of thermal analysis, thermal volatilisation and (laser) desorption techniques, or pyrolysis. In most cases mass spectrometric detection modes are used. Early MS work has focused on thermal desorption of the additives from the bulk polymer, followed by electron impact ionisation (El) [98,100], Cl [100,107] and field ionisation (FI) [100]. These methods are limited in that the polymer additives must be both stable and volatile at the higher temperatures, which is not always the case since many additives are thermally labile. More recently, soft ionisation methods have been applied to the analysis of additives from bulk polymeric material. These ionisation methods include FAB [100] and LD [97,108], which may provide qualitative information with minimal sample pretreatment. A comparison with FAB [97] has shown that LD Fourier transform ion cyclotron resonance (LD-FTTCR) is superior for polymer additive identification by giving less molecular ion fragmentation. While PyGC-MS is a much-used tool for the analysis of rubber compounds (both for the characterisation of the polymer and additives), as shown in Section 2.2, its usefulness for the in situ in-polymer additive analysis is equally acknowledged. 

Also, direct determination of additives by means of laser desorption in solid polymeric materials rather than in polymer extracts has been reported [266], Takayama et al. [267] have described the direct detection of additives on the surface of LLDPE/(Chimassorb 944 LD and Irgafos P-EPQ) after matrix (THAP)-coating. As shown in Scheme 7.13, direct inlet mass spectrometry is also applicable to transfer TLC-MS and TLC-MS/MS analyses without the need for prior analysis. For direct sample introduction a small amount of the selected... 

If we consider only a few of the general requirements for the ideal polymer/additive analysis techniques (e.g. no matrix interferences, quantitative), then it is obvious that the choice is much restricted. Elements of the ideal method might include LD and MS, with reference to CRMs. Laser desorption and REMPI-MS are moving closest to direct selective sampling tandem mass spectrometry is supreme in identification. Direct-probe MS may yield accurate masses and concentrations of the components contained in the polymeric material. Selective sample preparation, efficient separation, selective detection, mass spectrometry and chemometric deconvolution techniques are complementary rather than competitive techniques. For elemental analysis, LA-ICP-ToFMS scores high. 

By the sol-gel-process, inorganic glassy and hybrid polymeric materials are accessible at comparatively low temperatures [1], Therefore, organic molecules or dyes can easily be incorporated into the oxide matrix. This combination is especially attractive for the development of the following devices optical filters, solid-state lasers, optical switches, nonlinear optical laser hosts, optical data storage media, and photoconductive devices and films [2]. 

AIN, GaN, and InN are attractive materials for applications such as blue lasers and field emitters single-source precursors for these of formula [R2MNR 2]2 (R = alkyl, R = alkyl or H) have been reported.236 The reaction of alkylamines with group 13 trialkyl metal compounds affords oligomeric or polymeric ring and cage structures of metal amides and imides (see section on nitrides). 

Molecular Studies on Laser Ablation Processes of Polymeric Materials by Time-Resolved Luminescence Spectroscopy... 

Fluorescence Characterization of Ablated Polymeric Materials. In order to produce sharply etched patterns, the film was ablated with a photo-lithographically prepared mesh mask in the contact mode. The ablation was conducted with two laser shots with the laser fluence of 0.2 J/cm2. The decay curves of the ablated film was measured by a... 

ETEROAROMATics FURAN AND THIOPHENE. The chemical transformation of thiophene at high pressure has not been studied in detail. However, an infrared [441,445] study has placed the onset of the reaction at 16 GPa when the sample becomes yellow-orange and the C—H stretching modes involving sp carbon atoms are observed. This reaction threshold is lower than in benzene, as expected for the lower stability of thiophene. The infrared spectrum of the recovered sample differs from that of polythiophene, and the spectral characteristics indicate that it is probably amorphous. Also, the thiophene reaction is extremely sensitive to photochemical effects as reported by Shimizu and Matsunami [446]. Thiophene was observed to transform into a dark red material above 8 GPa when irradiated with 50 mW of the 514.5-nm Ar+ laser line. The reaction was not observed without irradiation. This material was hypothesized to be polythiophene because the same coloration is reported for polymeric films prepared by electrochemical methods, but no further characterization was carried out. 

---