Manufacturer’s information

Appropriate resources should be consulted for compatibility and stability information before mixing components (e.g., manufacturer s information, Trissel s Handbook on Injectable Drugs, and King Guide to Parenteral Admixtures). 

This publication is only intended to provide background information all information on drug administration, doses, and schedules should be reconfirmed for accuracy by referring to the manufacturer s information sheet. 

The manufacturer s information on the instrument should be read prior to the start of the experiment. It is also recommended that References 2,11,12, and 21-24 be read. 

Volume measurements include the use of pipettes, volumetric flasks, measuring cylinders, and burettes. Each has different calibration uncertainties that are detailed in the manufacturer s information supplied with the... 

Quantifying uncertainty components (from validation data, certificates of calibrations, manufacturer s information etc.) as standard deviations,... 

Cabinets designed for the storage of flammable chemicals should be properly used and maintained. Read and follow the manufacturer s information and follow these safety practices ... 

Phenytoin poisoning has been reported in a patient who took Chinese proprietary medicines containing phenytoin, carbamazepine, and valproate (63). The manufacturer s information leaflet did not mention any of these prescription drugs. 

Usual parenteral dosage IV Push Initially 0.25 mg/kg actual body weight over 2 min may repeat in 15 min at dose of 0.35 mg/kg actual body weight subsequent doses individualized IV Infusion After initial bolus injection 5-10 mg/h may increase at 5 mg/h up to 15 mg/h. Maintain over 24 h. Note Refer to manufacturer s information for dose concentration/infusion rate. 

Major elements of a CHP plan include listing of responsibilities for employers, employees, and a chemical hygiene officer. Also among the items that have to be covered in the plan is the stipulation that every laboratory must have a complete chemical inventory that is updated annually. A copy of the Material Safety Data Sheet (MSDS), which defines each chemical as toxic, carcinogenic, or dangerous, must be on file and readily accessible and available to aU employees 24 hours a day, 7 days a week. The MSDS contains important information for the benefit of laboratory employees. The chemical manufacturer s information as supplied on the MSDS is used to ascertain whether a certain chemical is hazardous. Each MSDS must give the product s... 

Although the IVLE dose should not exceed 2.5 g/kg per day or 60% of total daily calories, lower doses of 1 g/kg per day not to exceed 30% of calories have been recommended to minimize negative effects associated with long-chain fatty acids. Manufacturer s information recommends IVLE infusion over 4 to 8 hours for adults. However, infusion over 16 to 24 hours appears to be the best clinical strategy... 

CAMAG). According to the manufacturer s information, the latter are not available in light-weight material, as chambers of this size do not weigh very much even in the normal material. 

The photocatalyst (Ti02) used in this work was Degussa P25. Based on the manufacturer s information, the titania particles are a mixture of anatase and rutile crystalline phases (mostly anatase). Ti02 has an average particle size of 30nm and surface area 50 mVg. The other photocatalyst used was ZnO powder (Merck), about 99% pure, possessing BET surface area 4.5 m /g. The reactive red MSB dye (Chika Ltd) was used as such in the present study. 

Nolice Endcapped C, phases are suilable for ihc separaiion of basic soluies. The C j phase has been treated in a second step with a small silane molecule. Because it is small and therefore sierically compatible, ii can reach the deeperlying, less reactive silanol groups. As a result you will get a surface ihar contains less active silanol groups. Fewer problems therefore arise during the separation of polar groups, because no additional interactions of a polar nature are possible. Endcapping can be found sometimes within the manufacturer s information about the column marked as e or E , see also Tip No. 1. 

Estimate based on manufacturer s information and national averages revised to reflect Vermont conditions. Assume 1,800 hr/yr operation. Labor ... 

Software maintenance is currently 32 percent of a manufacturer s information technology budget. With the move to SaaS solutions, many companies can eliminate the maintenance charges and the headcount to service the software. It also increases a company s flexibility to stay current on new releases. 

One good source for manufacturer s information on placement machines and most other equipment used in the various SMT production and testing phases is the annual Directo/y of Suppliers to the Electronics Manufacturing Industry published by Electronic Packaging and Production (see Further Information section ). Among the elements to consider in the selection of placement equipment, whether fully automated or X-Y-vacuum assist tables, are... 

G, gel-type resin M, macroreticular resin. Manufacturer s information. 

From the low pressure data of this adsorption isotherm we could calculate the micropore spectrum (d < 2 nm) of the activated carbon. It is sketched in Figure 3.8. It clearly shows that this activated carbon has a considerable amount of micropores (diameter d < 2 nm = 20 A). The specific volume of all micropores calculated by integration of the pore spectrum in Fig. 3.8 is Vmicro = 0.626 cmVg AC. The specific volume of all pores with diameters (d < 120 nm) determined from combined Ar- and N2 measurements was 0.715 cm / g. The total pore volume including also macropores was 1.04 cm / g according to manufacturer s information. 

TABLE 8.5 Properties of Some Commercial Acrylic Otherwise Indicated) Dispersions Used in Conservation (Manufacturer s Information Unless ... 

The propagation of uncertainties requires knowledge of the sources and values of uncertainty in variables, which when combined, contribute to the uncertainty in the (final) dependent variable. In following the path, one often finds interdependence of variables and sometimes the reduction of uncertainty magnitudes [1]. In manometric adsorption uncertainty analyses, the dependent variable is the specific surface excess amount, derived fiom EoS applications. In EoS uncertainty analysis, the dependent variable is the amount of fluid in the continuous phase above the sample, regardless of whether it is calculated directly via a cubic EoS or indirectly via a multiple parameters EoS. The SU-values used in this work were either measured or identified in manufacturer s information and taken to be 3-o-standard deviations. These values are summarized in Table 1. Since the standard deviation of the sample... 

---