Mandrell

Electrophoretic deposition (EPD) is anotlier metliod of casting slurries. EPD is accomplished tlirough tire controlled migration of charged particles under an applied electric field. During EPD, ceramic particles typically deposit on a mandrel to fonn coatings of limited tliickness, or tliin tubular shapes such as solid (3 " - AI2O2 electrolytes for sodium-sulfur batteries. 

The Stedman-type column is shown in Fig. 11, 56, 25. The characteristic features are (i) the use of a fine stainless steel wire cloth formed into conical discs, and (ii) an accurately fitting Pyrex glass jacket, produced by shrinking Pyrex glass on mandrels to the required inside dimensions. Modifications incorporating a silvered vacuum jacket and an electrically-heated jacket are marketed. This column is said to possess high efficiency but is expensive. It is generally employed in conjunction with a total-condensation variable take-off still head. 

Vertica.1 Axia.1 Deposition. The vertical axial deposition (VAD) process (18) was developed by a consortium of Japanese cable manufacturers and Nippon Telephone and Telegraph (NTT). This process also forms a cylindrical soot form. However, deposition is achieved end-on without use of a mandrel and subsequent formation of a central hole. Both the core and cladding are deposited simultaneously using more than one torch (Fig. 12). 

Downward extmsion of a bubble into a water bath and over an inner water-cooled mandrel is used in a few instances for polypropylene and polyesters. The water is removed prior to slitting and winding. 

One ASTM test procedure has suggested (24) that foamed plastics be classified as either rigid or flexible, a flexible foam being one that does not mpture when a 20 x 2.5 x 2.5 cm piece is wrapped around a 2.5 cm mandrel at a uniform rate of 1 lap/5 s at 15—25°C. Rigid foams are those that do mpture under this test. This classification is used in this article. 

These ahoys are used as fuses, sprinkler system ahoys, foundry pattern ahoys, molds, dies, punches, cores, and mandrels where the low melting ahoy is often melted out of a mold. The ahoys are also used as solders, for the repHcation of human body parts (see Prosthetic devices), and as filler for tube bending. Lead—iadium ahoys are often used to joia metals to glass. 

Testing of Painted Products. The enhancement of paint adhesion is one of the principal functions of conversion coating (20—22). A group of tests based on product deformation is used to test the painted product. The appHance and cod-coating industries use the mandrel bend, the cross-hatch adhesion test, and the direct and reverse impact tests. Adhesion after a water soak is judged using a cross-hatch test performed on the exposed surface. 

Chemical Properties. LLDPE is chemically stable. Very few analyses and tests related to its chemical properties are carried out routinely. Resistance to thermal stress-cracking is determined by exposing film wrapped on a metal mandrel to hot (100°C) air for 48, 96, and 168 hours (ASTM D2951-71). 

Pipe and Tubing. A typical die for extmding tubular products is shown in Figure 4. It is an in-line design, ie, the center of the extmded pipe is concentric with the extmder barrel. The extmdate is formed into a tube by the male and female die parts. The male die part is supported in the center by a spider mandrel. Melt flows around legs of the mandrel and meets on the downstream side. The position of the female die part can be adjusted with bolts adjustment is requited to obtain a tube with a uniform wall thickness. 

Fig. 4. Pipe or tubing die for in-line extmsion A, die body B, mandrel, pin, and male die part C, die, die bushing, and female part D, die-retaining ring E, die-retaining bolt F, die-centered bolt G, spider leg H, air hole I, seat for breaker plate J, ring for attachment to extmder and K, die land (15).

Dissolution of Silver. Silver is dissolved by oxidising acids and alkaU metal cyanide solutions in the presence of oxygen. The latter method is the principal technique for dissolving silver from ore. Silver has extensive solubiUty in mercury (qv) and low melting metals such as sodium, potassium, and their mixtures. Cyanide solutions of silver are used for electroplating and electroforming. The silver is deposited at the cathode either as pure crystals or as layers on a mandrel. 

Fig. 2. Configuration for spirally wound rechargeable lithium ceU. A, Cap B, cathode tab C, insulating disk (2) D, mandrel E, can F, bak G, safety vent ...

Electrophoretic casting (38,59) is accompHshed by inducing controUed migration of charged particles under an appHed electric field to deposit on a mandrel. Thin tubular shapes and coatings of limited thickness are formed using this technique. Electrophoretic deposition (EPD) is also used to manufacture thin waU, soHd P -alumina [12005-16-2] NaAl Og, electrolytes for sodium—sulfur batteries. 

---