Isobutene from catalytic cracking

Isoprene is the second important conjugated diene for synthetic rubber production. The main source for isoprene is the dehydrogenation of C5 olefins (tertiary amylenes) obtained by the extraction of a C5 fraction from catalytic cracking units. It can also be produced through several synthetic routes using reactive chemicals such as isobutene, formaldehyde, and propene (Chapter 3). 

Isobutene is present in refinery streams. Especially C4 fractions from catalytic cracking are used. Such streams consist mainly of n-butenes, isobutene and butadiene, and generally the butadiene is first removed by extraction. For the purpose of MTBE manufacture the amount of C4 (and C3) olefins in catalytic cracking can be enhanced by adding a few percent of the shape-selective, medium-pore zeolite ZSM-5 to the FCC catalyst (see Fig. 2.23), which is based on zeolite Y (large pore). Two routes lead from n-butane to isobutene (see Fig. 2.24) the isomerization/dehydrogenation pathway (upper route) is industrially practised. Finally, isobutene is also industrially obtained by dehydration of f-butyl alcohol, formed in the Halcon process (isobutane/propene to f-butyl alcohol/ propene oxide). The latter process has been mentioned as an alternative for the SMPO process (see Section 2.7). 

C4 cuts from catalytic cracking contain little butadiene and acetylenic compounds. Hence they can be used directly for isobutene separation processes, but require prior hydrogenation to obtain 1-butene. By contrast, steam cracked effluents must systematically undergo hydrogenation pretreatmcnL This is necessary to eliminate the compounds liable to cause highly exothermic side-polymerizations, and to form gums that disturb the operation of the catalyst systems, solvents and adsorbents used in steps designed to produce the different C4 olefins. 

Qi, Z., Sundmacher, K., Stein, E., Kienle, A., and Kolah, A. Reactive separation of isobutene from c4 crack fractions by catalytic distillation processes. Separation and Purification Technology, 26(2-3) 147-163, 2002. 

The three isomers constituting n-hutenes are 1-hutene, cis-2-hutene, and trans-2-hutene. This gas mixture is usually obtained from the olefinic C4 fraction of catalytic cracking and steam cracking processes after separation of isobutene (Chapter 2). The mixture of isomers may be used directly for reactions that are common for the three isomers and produce the same intermediates and hence the same products. Alternatively, the mixture may be separated into two streams, one constituted of 1-butene and the other of cis-and trans-2-butene mixture. Each stream produces specific chemicals. Approximately 70% of 1-butene is used as a comonomer with ethylene to produce linear low-density polyethylene (LLDPE). Another use of 1-butene is for the synthesis of butylene oxide. The rest is used with the 2-butenes to produce other chemicals. n-Butene could also be isomerized to isobutene. ... 

The modem gasolines are produced by blending products from cmde oil distillation, that is, fluid catalytic cracking, hydrocraking, reforming, coking, polymerization, isomerization, and alkylation.Two clear examples of the possible use of solid-acid catalysts in refining processes are the isomerization of lineal alkanes and the alkylation of isobutene with butanes. In both these cases, and due to the octane... 

Besides ethylene and propylene, the steam cracking of naphtha and catalytic cracking in the refinery produce appreciable amounts of C4 compounds. This C4 stream includes butane, isobutane, 1-butene (butylene), cis- and trans-2-hutene, isobutene (isobutylene), and butadiene. The C4 hydrocarbons can be used to alkylate gasoline. Of these, only butadiene and isobutylene appear in the top 50 chemicals as separate pure chemicals. The other C4 hydrocarbons have specific uses but are not as important as butadiene and isobutylene. A typical composition of a C4 stream from steam cracking of naphtha is given in Table 8.3. 

Figure 3.35 shows a process flow diagram of Phillips MTBE/ETBE/TAME process. This process is often called the Phillips Etherification Process. The reaction section (1,2) which receives methanol and isobutene concentrate, contains an ion exchange resin. The isobutene concentrate may be mixed olefins from a Fluid Catalytic Cracking Unit (FCCU) or steam cracker or from the on-purpose dehydration of isobutene (Phillips STAR process). High purity MTBE (99 wt%) is removed as a bottoms product from the MTBE fractionator (3). AH of the unreacted methanol is taken overhead, sent to a methanol... 

Fig. 5.1. Chromatograms of products of catalytic cracking (A) without reactor and (B) with reactor. Sorbent, 11% quinoline on refractory brick temperature, 25 C column length, 10.5 m. Peaks 1 = propane 2 = propylene 3 = isobutane 4 = n-butane 5 = isobutene 6 = butene-1 7 = rmns-butene-2 8 = cis-butene-2 9 = isopentane 10 = 3-methylbutene-l 11 = n-pentane 12 = pentene-1 13 = 2,2-dimethylbutene 14 = 2-methylbutene-l 15 = tnms-pentene-2 16 = cfsi)entene-2 17 = 2-methyl-butene-2 18 = 2,3-dimethylbutane 19 = 2-methylpentane 20 = 3-methylpentane 21 = 3-methylpen-tene-1 22 = 4-methylpentene-l 23 = c -4-methylpentene-2 24 = cyclopentane 25 = 2,3-dimethyl-butene-1 26 = fmns-4-methylpentene-2 27 = w-hexane 28 = cyclopentene 29 = 2-methylpentene-l 30 = hexene-1 31 = 2,4-dimethylpentane 32 = cis-hexene-3 33 = tnms-hexene-3 34 = 2-ethylbu-tene-1 35 = trans-hexene-2 36 = methylcyclopentane 37 = cis-methylpentene-2 38 = 2-methylpen-tene-2 39 = pisns-3-methylpentene-2 40 = methylcyclopentene-4 41 = 4-methylcyclopentene 42 = cw-3-methylpentene-2 43 = 2,3-dimethylpentane 44 = 2-methylheptane 45 = 2,3-dimethylbutene-2 46 = methylheptane 47 = cyclohexane 48 = C, olefin. Reprinted with permission from ref. 1.

MTBE is produced by reacting methanol with isobutene. Isobutene is contained in the C4 stream from steam crackers and from fluid catalytic cracking m the crude oil-refining process. However, isobutene has been in short supply in many locations. The use of raw materials other than isobutene for MTBE production has been actively sought. Figure 2 describes the reaction network for MTBE production. Isobutene can be made by dehydration of i-butyl alcohol, isomerization of -butenes [73], and isomerization and dehydrogenation of n-butane [74, 75]. t-Butanol can also react with methanol to form MTBE over acid alumina, silica, clay, or zeolite in one step [7678]. t-Butanol is readily available by oxidation of isobutane or, in the future, from syngas. The C4 fraction from the methanol-to-olefins process may be used for MTBE production, and the C5 fraction may be used to make TAME. It is also conceivable that these... 

The radiolysis/EPR study of isobutene was supported by experiments on Cj-Cg olefins on both HZSM5 and NaZSMS (Table 1). This eillowed screening for possible radical cation reactions (minimal for these compounds), and the survey of related compounds aided spectroscopic assignment and tested the catalytic reaction steps from different starting points. For example, 2 was also formed from C and Cg feed molecules, corroborating the conclusion that 2 can be formed from isobutene by cracking the dimer as opposed to addition of C4 and Cj units. 

The distribution of the products obtained from this reaction depends upon the reaction temperature (Fig. 5.2-2) and differs from other polyethylene recycling reactions in that aromatics and alkenes are not formed in significant concentrations. Another significant difference is that this ionic liquid reaction occurs at temperatures as low as 90 °C, whereas conventional catalytic reactions require much higher temperatures, typically 300-1000 °C [90j. A patent filed under the Secretary of State for Defence (UK) has reported a similar cracking reaction for lower molecular weight hydrocarbons in chloroaluminate(iii) ionic liquids [91]. An example is the cracking of hexane to products like propene and isobutene (Scheme 5.2-40). The reaction was... 

---