Infrared Compositions

The spectral efficiency of a flare composition is closely related to the combustion enthalpy of the flare composition, the plume temperature and the spectral emissivity of its combustion products as described in Eq. (10.18) 

The combustion enthalpy of the flare, Ac H, is the sum of both the primary anaerobic reaction enthalpy and the afterburn reaction enthalpy with the atmospheric oxygen. Thus for an Mg/Teflon /Viton (60/30/10) payload, this ideally translates into 

---

Toon, G.C., C.B. Farmer, P.W. Schafer, L.L. Lowes, R.H. Norton, M.R. Schoeberl, L.R. Lait, and P.A. Newman, Evidence for subsidience in the 1989 Arctic winter stratosphere from airborne infrared composition measurements. J Geophys Res 97, 7963, 1992b. 

Analytical investigations may be undertaken to identify the presence of an ABS polymer, characterize the polymer, or identify nonpolymeric ingredients. Fourier transform infrared (ftir) spectroscopy is the method of choice to identify the presence of an ABS polymer and determine the acrylonitrile—butadiene—styrene ratio of the composite polymer (89,90). Confirmation of the presence of mbber domains is achieved by electron microscopy. Comparison with available physical property data serves to increase confidence in the identification or indicate the presence of unexpected stmctural features. Identification of ABS via pyrolysis gas chromatography (91) and dsc ((92) has also been reported. 

Infrared spectra of fats and oils are similar regardless of their composition. The principal absorption seen is the carbonyl stretching peak which is virtually identical for all triglyceride oils. The most common appHcation of infrared spectroscopy is the determination of trans fatty acids occurring in a partially hydrogenated fat (58,59). Absorption at 965 - 975 cm is unique to the trans functionaHty. Near infrared spectroscopy has been utilized for simultaneous quantitation of fat, protein, and moisture in grain samples (60). The technique has also been reported to be useful for instmmental determination of iodine value (61). 

Measurement of Unsaturation. The presence of double bonds in a fatty acid side chain can be detected chemically or through use of instmmentation. Iodine value (IV) (74) is a measure of extent of the reaction of iodine with double bonds the higher the IV, the more unsaturated the oil. IV may also be calculated from fatty acid composition. The cis—trans configuration of double bonds may be deterrnined by infrared (59) or nmr spectroscopy. Naturally occurring oils have methylene-intermpted double bonds that do not absorb in the uv however, conjugated dienes maybe deterrnined in an appropriate solvent at 233 nm. 

Polyester composition can be determined by hydrolytic depolymerization followed by gas chromatography (28) to analyze for monomers, comonomers, oligomers, and other components including side-reaction products (ie, DEG, vinyl groups, aldehydes), plasticizers, and finishes. Mass spectroscopy and infrared spectroscopy can provide valuable composition information, including end group analysis (47,101,102). X-ray fluorescence is commonly used to determine metals content of polymers, from sources including catalysts, delusterants, or tracer materials added for fiber identification purposes (28,102,103). 

Poly(vinyl acetate). The dielectric and mechanical spectra of hybrids produced by mixing a poly(vinyl acetate)—THE solution with TEOS, followed by the addition of HCl have been investigated (45). Mixtures were made which were beheved to be 0, 5, 10, 15, and 20 wt % Si02, respectively. These composites were transparent and Eourier transform infrared spectroscopy (ftir) revealed hydrogen bonding between the siUcate network and carbonyl units of the poly(vinyl acetate) (PVAc). No shift in the T of the composites from that of the pure PVAc was observed. Similarly, the activation... 

The formation of such materials may be monitored by several techniques. One of the most useful methods is and C-nmr spectroscopy where stable complexes in solution may give rise to characteristic shifts of signals relative to the uncomplexed species (43). Solution nmr spectroscopy has also been used to detect the presence of soHd inclusion compound (after dissolution) and to determine composition (host guest ratio) of the material. Infrared spectroscopy (126) and combustion analysis are further methods to study inclusion formation. For general screening purposes of soHd inclusion stmctures, the x-ray powder diffraction method is suitable (123). However, if detailed stmctures are requited, the single crystal x-ray diffraction method (127) has to be used. 

Infrared patterns can lead to detection of lack of bonding between surface platings, between coatings and base metal, or within bra2ed honeycombs and other composite materials where bonding is vital. Mote recent developments involve infrared television or image tubes similar to the types used for night vision in military and other appHcations. 

Instmmental methods of analysis provide information about the specific composition and purity of the amines. QuaUtative information about the identity of the product (functional groups present) and quantitative analysis (amount of various components such as nitrile, amide, acid, and deterruination of unsaturation) can be obtained by infrared analysis. Gas chromatography (gc), with a Hquid phase of either Apiezon grease or Carbowax, and high performance Hquid chromatography (hplc), using siHca columns and solvent systems such as isooctane, methyl tert-huty ether, tetrahydrofuran, and methanol, are used for quantitative analysis of fatty amine mixtures. Nuclear magnetic resonance spectroscopy (nmr), both proton ( H) and carbon-13 ( C), which can be used for quaHtative and quantitative analysis, is an important method used to analyze fatty amines (8,81). 

---