Infill

Deltaic (distributary channel) Isolated or stacked channels usually with fine grained sands. May or may not be in communication Good producers permeabilities of 500-5000mD. Insufficient communication between channels may require infill wells in late stage of development... 

Thermal Recovery Polymer Flooding Infill Wells... 

One category of remaining oil shown in the above diagram is unproducible oil in thin oil rims, which cannot be produced without coning in unwanted oil and/or gas. Horizontal wells are an ideal form of infill well in this situation, and will be discussed in Section 9.3. 

Keywords production decline, economic decline, infill drilling, bypassed oil, attic/cellar oil, production potential, coiled tubing, formation damage, cross-flow, side-track, enhanced oil recovery (EOR), steam injection, in-situ combustion, water alternating gas (WAG), debottlenecking, produced water treatment, well intervention, intermittent production, satellite development, host facility, extended reach development, extended reach drilling. 

The principles discussed in this section enable the calculation of air infil-tration/exfiltration, provided that the following quantities are known or can... 

Infill drilling is another possible way to extend production. For a variety of reasons, some oil may not be available to the original wells in the resei voir. Some wells may be spaced too far apart to capture the oil between them. Gas or water flooding may have bypassed some oil, or fractures or faults may block off certain parts of the reservoir from the rest so that they cannot be drained from existing wells. In these cases drilling new wells between existing ones call be an effective way to capture more of the resource. 

Secondary recovery, infill drilling, various pumping techniques, and workover actions may still leave oil, sometimes the majority of the oil, in the reservoir. There are further applications of technology to extract the oil that can be utilized if the economics justifies them. These more elaborate procedures are called enhanced oil recovery. They fall into three general categories thermal recoveiy, chemical processes, and miscible methods. All involve injections of some substance into the reservoir. Thermal recovery methods inject steam or hot water m order to improve the mobility of the oil. They work best for heavy nils. In one version the production crew maintains steam or hot water injection continuously in order to displace the oil toward the production wells. In another version, called steam soak or huff and puff, the crew injects steam for a time into a production well and then lets it soak while the heat from the steam transfers to the resei voir. After a period of a week or more, the crew reopens the well and produces the heated oil. This sequence can be repeated as long as it is effective. 

Sub-grade the material at formation level after excavating or infilling ... 

This method was also applied to the surface modified Y-TZP ceramics shown previously in Figure 3.5.7. Linearized BET plots [24] extracted from regions of interest within the 35 % porosity ceramic corresponding to the outer ring (infil-... 

NOTE 24 records were read from the infile C normal ranges.txt. ... 

Lanthanide-doped inverse photonic crystals have been reported.282 The lattices were prepared by infilling self-assembled polystyrene sphere templates with a mixture of zirconium alkoxide and europium at 450 °C, the polystyrene spheres were burnt out leaving hollow spheres of air, and the infilled material was converted to Zr02 Eu3+. The PL properties of the resulting photonic lattice were reported.282 The possibility of including phosphors into photonic lattices could lead to many... 

In 1980 the Consumer Protection Act (15) required manufacturers to take reasonable steps to ensure that fabric -soft infill composites of domestic furniture resisted the cigarette test of BS5852 Part 1. These regulations did not apply to rouchings, trims to seat platforms etc. but only to the primary upholstery composites. The Consumer Protection Amendment of 1983 required specified children s furniture containing cellular materials had to resist Source 5 of BS 5852 Part 2. (16)... 

The Consumer Safety Regulations 1988 regulations were recently published for domestic furniture and mattresses. These are a complex series of relatively simple ignition tests designed to restrict the use of easily ignitable fabrics and infill materials. The 1988 regulations replace the earlier regulations of 1980 and 1983. 

Specific machines, for example to produce infill domestic door panels. 

Two types of metal-rich hydrogenous deposits are formed on the seafloor iron-manganese oxides and polymetallic sulfides. The iron-manganese oxides have been deposited as nodules, sediments, and crusts. They are enriched in various trace elements, such as manganese, iron, copper, cobalt, nickel, and zinc, making them a significant repository for some of these metals. Most of the metals in the polymetallic sulfides are of hydrothermal origin. These sulfides have been deposited as metalliferous sediments aroimd hydrothermal systems and as rocks that infill cracks within former... 

---