Induction selection

Heigold, S., Sets, C., Bechtel, W., Ivanovas, B., Schafer, R., and Bauer, G. (2002). Nitric oxide mediates apoptosis induction selectively in transformed fibroblasts compared to nontrans-formed fibroblasts. Carcinogenesis 25(6), 929-941. 

The measurement and evaluation methods of chapter 3.1. and 3.2. work with inductive sensors in an absolute circuit. The results on two different formed coils, a pot core coil and a cylinder core coil are selected. For presentation in this paper the third method, described in chapter 3.3., uses a Hall-effect device to detect the information and a coil system in a differential circuit to excite the electromagnetic field. 

The TT-inductive effect describes how an inductive substituent might selectively influence the electron distribution at the o- and -positions of the aromatic nucleus. A familiar example is represented by the... 

In unsaturated molecules electronic effects can be transmitted by mesomerism as well as by inductive effects. As with the latter, the mesomeric properties of a group are described by reference to hydrogen. Groups which release electrons to the unsaturated residue of the molecule are said to exert a +Af effect, whereas groups which attract electrons are said to exert a —Af effect. In aromatic structures the important feature of an M-substituent is that it influences the 0- and p-positions selectively. 

A unique capability of induction heating is apparent in its abdity to heat the surface of a part to a high temperature whde the interior remains at room temperature. Proper selection of material, high frequency, and high power density can produce a thin surface hardness with a heat unaffected core (3). Figure 4 shows the cross section of a typical automotive shaft heated with 10 kH2 at various power densities. The required hardness depth is selected to... 

Frequency Selection. When estabhshing the specifications for a coreless induction furnace, the material to be melted, the quantity of metal to be poured for each batch, and the quantity to be produced per hour must be considered simultaneously. Graphs have been developed that combine these factors with practical experience to indicate possible solutions for a specific requirement. 

Oxygen and nitrogen also are deterrnined by conductivity or chromatographic techniques following a hot vacuum extraction or inert-gas fusion of hafnium with a noble metal (25,26). Nitrogen also may be deterrnined by the Kjeldahl technique (19). Phosphoms is determined by phosphine evolution and flame-emission detection. Chloride is determined indirecdy by atomic absorption or x-ray spectroscopy, or at higher levels by a selective-ion electrode. Fluoride can be determined similarly (27,28). Uranium and U-235 have been determined by inductively coupled plasma mass spectroscopy (29). 

Atomic Absorption/Emission Spectrometry. Atomic absorption or emission spectrometric methods are commonly used for inorganic elements in a variety of matrices. The general principles and appHcations have been reviewed (43). Flame-emission spectrometry allows detection at low levels (10 g). It has been claimed that flame methods give better reproducibiHty than electrical excitation methods, owing to better control of several variables involved in flame excitation. Detection limits for selected elements by flame-emission spectrometry given in Table 4. Inductively coupled plasma emission spectrometry may also be employed. 

A novel interface to connect a ce system with an inductively coupled plasma mass spectrometric (icpms) detector has been developed (88). The interface was built using a direct injection nebulizer (din) system. The ce/din/icpms system was evaluated using samples containing selected alkah, alkaline earths, and heavy-metal ions, as well as selenium (Se(IV) and Se(VI)), and various inorganic and organic arsenic species. The preliminary results show that the system can be used to determine metal species at ppt to ppb level. 

The most common detectors in HPLC are ultraviolet, fluorescence, electrochemical detector and diffractometer. However, despite all improvements of these techniques it seems necessary to have a more selectivity and sensitivity detector for the purposes of the medical analysis. It should be therefore improvements to couple analytical techniques like infrared IR, MS, nuclear magnetic resonance (NMR), inductively coupled plasma-MS (ICP-MS) or biospecific detectors to the LC-system and many efforts have been made in this field. 

Safety Standards (enclosures) for construction and guide for selection, installation and use of rotating machines Sound level prediction for insulated rotating electrical machines Energy management guide for selection and use of three phase motors Polyphase induction motors for power generating stations... 

---