INDEX measurements

Solution Polymers. Acryflc solution polymers are usually characterized by their composition, solids content, viscosity, molecular weight, glass-transition temperature, and solvent. The compositions of acryflc polymers are most readily determined by physicochemical methods such as spectroscopy, pyrolytic gas—liquid chromatography, and refractive index measurements (97,158). The solids content of acryflc polymers is determined by dilution followed by solvent evaporation to constant weight. Viscosities are most conveniently determined with a Brookfield viscometer, molecular weight by intrinsic viscosity (158), and glass-transition temperature by calorimetry. 

The width of molecular weight distribution (MWD) is usually represented by the ratio of the weight—average and the number—average molecular weights, MJM. In iadustry, MWD is often represented by the value of the melt flow ratio (MER), which is calculated as a ratio of two melt indexes measured at two melt pressures that differ by a factor of 10. Most commodity-grade LLDPE resias have a narrow MWD, with the MJM ratios of 2.5—4.5 and MER values in the 20—35 range. However, LLDPE resias produced with chromium oxide-based catalysts have a broad MWD, with M.Jof 10—35 and MER of 80-200. 

The molecular weight distribution of LLDPE resins is usually characterized in industry by the ratios of melt indexes measured in the same apparatus using different loads (2.16, 10.16, and 21.6 kg). The commonly used ratios are melt flow ratio, MFR) and I q/I2. Both of these ratios... 

Optical properties also provide useful stmcture information about the fiber. The orientation of the molecular chains of a fiber can be estimated from differences in the refractive indexes measured with the optical microscope, using light polarized in the parallel and perpendicular directions relative to the fiber axis (46,47). The difference of the principal refractive indexes is called the birefringence, which is illustrated with typical fiber examples as foUows. Birefringence is used to monitor the orientation of nylon filament in melt spinning (48). 

Water Content and Refractive Index. The water content of a hydrophilic contact lens is a determinant of other properties. The relationship of water content and Dk is discussed above. Water content in lenses is inversely related to refractive index (23), a key property for vision correction. A lens material with a higher refractive index refracts light to a greater degree, allowing more vision correction with a thinner material. The water content of a lens is generally determined gravimetricaHy or inferred from the relationship to refractive index, measured with a refractometer (24). 

The reaction mixture is heated and allowed to reflux, under atmospheric pressure at about 100°C. At this stage valve A is open and valve B is closed. Because the reaction is strongly exothermic initially it may be necessary to use cooling water in the jacket at this stage. The condensation reaction will take a number of hours, e.g. 2-4 hours, since under the acidic conditions the formation of phenol-alcohols is rather slow. When the resin separates from the aqueous phase and the resin reaches the requisite degree of condensation, as indicated by refractive index measurements, the valves are changed over (i.e. valve A is closed and valve B opened) and water present is distilled off. 

Fig. 12.11 (a) Haring-Blum cell for throwing index measurement, in elevation and (b) Hull cell... 

It is important to note that comparable information to that obtained from infra-red spectroscopy can in principle be obtained from refractive index measurements. It has been shown that for a transversely isotropic film, the relationship equivalent to 11(c) is... 

The amorphous orientation can also be obtained, following conventional procedures, by combining X-ray and refractive index measurements, assuming the additivity... 

Ross, K.F.A. Billing, E. (1957). The water and solid content of living bacterial spores and vegetative cells as indicated by refractive index measurements. Journal of General Microbiology, 17, 418-25. 

The theory of counterion condensation is implicit in Oosawa (1957) but the term was coined later (Imai, 1961). The phenomenon was demonstrated by Ikegami (1964), using refractive index measurements of the interaction between sodium and polyacrylate ions. It has since been confirmed for many mono-, di- and trivalent counterions and polyionic species (Manning, 1979). 

Most suitable for the examination of the surface is x-ray photoelectron spectroscopy, whereas the wettability determination can be established by a detailed interpretation of core flooding experiments and wettability index measurements. The results of such studies show that the organic carbon content in the surface is well correlated with the wetting behavior of the material characterized by petrophysical measurements [1467,1468]. 

The HcReynolds abroach, which was based on earlier theoretical considerations proposed by Rohrschneider, is formulated on the assumption that intermolecular forces are additive and their Individual contributions to retention can be evaluated from differences between the retention index values for a series of test solutes measured on the liquid phase to be characterized and squalane at a fixed temperature of 120 C. The test solutes. Table 2.12, were selected to express dominant Intermolecular interactions. HcReynolds suggested that ten solutes were needed for this purpose. This included the original five test solutes proposed by Rohrschneider or higher molecular weight homologs of those test solutes to improve the accuracy of the retention index measurements. The number of test solutes required to adequately characterize the solvent properties of a stationary phase has remained controversial but in conventional practice the first five solutes in Table 2.12, identified by symbols x through s have been the most widely used [6). It was further assumed that for each type of intermolecular interaction, the interaction energy is proportional to a value a, b, c, d, or e, etc., characteristic of each test solute and proportional to its susceptibility for a particular interaction, and to a value x, X, Z, U, s, etc., characteristic of the capacity of the liquid phase... 

The next step in this study is to test this control algorithm on the actual laboratory reactor. The major difficulty is the direct measurement of the state variables in the reactor (T, M, I, W). Proposed strategy is to measure total mols of polymer (T) with visible light absorption and monomer concentration (M) with IR absorption. Initiator concentration (I) can be monitored by titrating the n-butyl lithium with water and detecting the resultant butane gas in a thermal conductivity cell. Finally W can be obtained by refractive index measurements in conjuction with the other three measurements. Preliminary experiments indicate that this strategy will result in fast and accurate measurements of the state vector x. 

UV spectra were recorded using a Perkin-Elmer Coleman 575 spectrometer. Yellowness index measurements (ASTM-D-1925) of film samples were made using a Colormaster Model V colorimeter. 

Ross and Billing, by means of refractive index measurements on spores and vegetative cells of B. cereus, B. cereus var. mycoides, and B. megaterium, found the values to be very high and comparable with that of dehydrated protein. This suggested that they contained much less water than the vegetative cells. 

Refractive index measurements indicated an adsorbance of 2 0.5 mg m 2 of the polymer onto the mica surfaces. 

Oxygen-Index Measurements. The measurement of oxygen-index was performed by bottom ignition, as discussed by Stuetz (11). 

Wei, T. Han, Y. Li, Y. Tsai, H. L. Xiao, H., Temperature insensitive miniaturized fiber inline Fabry Perot interferometer for highly sensitive refractive index measurement, Opt. Express 2008, 16, 5764 5769... 

The device has an all-glass structure and does not involve assembly of multiple components. As a result, we expect that the device will have very small temperature dependence. In addition, the open micronotch FP cavity allows prompt access to gas or liquid samples for direct refractive index measurement, making it possible to be used as an ultracompact chemical sensor based on refractive index measurement. 

To evaluate its capability for refractive index measurement, the fiber FPI device was tested using various liquids including methanol, acetone, and 2-propanol at room temperature. The interference spectra of the device immersed in various liquids are shown in Fig. 7.12 for comparison. The signal intensity dropped when the device was immersed in liquids as a result of the reduced refractive index contrast and thus lowered Fresnel reflections from the cavity endfaces. However, the interference fringes maintained a similar visibility. The spectral distance between the two adjacent valleys also decreased, indicating the increase of refractive index of the medium inside the cavity. Using (7.4), the refractive indices of the liquids were calculated to be nmethanoi = 1 -3283, acetone = 1 -3577, and n2-propanoi = 1.3739, which was close to the commonly accepted values. 

---