Hydrogen peroxide purification

The decomposition of aqueous hydrogen peroxide is minimized by various purification steps during manufacture, use of clean passive equipment, control of contaminants, and the addition of stabilizers. The decomposition is zero-order with respect to hydrogen peroxide concentration. 

The residue is leached to give cesium sulfate solution, which can be converted to cesium chloride by ion exchange on Dowex 50 resin and elution with 10% HCl, treatment using ammonia or lime, to precipitate the alurninum, or by solvent extraction, followed by purification at neutral pH using hydrogen peroxide or ammonia. 

P-Hydroxy-A-norpregn-3(5)-en-2-one (7) A solution of the hydroxy-methylene steroid (5) (24.8 g) dissolved in 240 ml of acetic acid and 240 ml of ethyl acetate is ozonized at — 10° with one molar equivalent of ozone. The resulting solution is diluted with 240 ml. of water and 60 ml of 30 % hydrogen peroxide and allowed to stand overnight. The solution is diluted with 1.5 liters of water and extracted with 3 x 700 ml portions of ethyl acetate. The combined extracts are washed with water, saturated sodium chloride solution, dried over sodium sulfate and concentrated to dryness under vacuum, leaving 23.4 g of a colorless amorphous residue of crude diacid. This material shows a maximum in the ultraviolet spectrum at 224 mp (s 6,400) indicating a 53 % yield of unsaturated acid (6). It is used without further purification. 

A solution of 1 equivalent of the oxazolidinone in diethyl ether is cooled to —78 C. To the resultant suspension are added 1.4 equivalents of triethylamine. followed by 1.1 equivalents of dibutylboryl triflate. The cooling bath is removed and the reaction mixture is stirred at 25 °C for 1.5 h. The resultant two-phase mixture is cooled to — 78 "C with vigorous stirring. After 1 equivalent of aldehyde is added, the reaction is stirred at —78 °C Tor 0.5 h, and 0 "C for 1 to 2 h. The solution is diluted with diethyl ether, washed with 1 N aq sodium bisulfate, and concentrated. Following oxidation with 30% aq hydrogen peroxide (10 equivalents, 1 1 methanol/water, 0 C. 1 h), extractive workup and chromatographic purification, the aldol adduct is obtained with >99% diastcrcomeric purity. 

The distilled product can be used as a catalyst, although it usually has a relatively strong phenylphosphine odor. It is quite deliquescent, and it has not been satisfactorily recrystallized. If rigorous purification and deodorization are desired, the product is dissolved in water, a small amount of hydrogen peroxide is added to oxidize the phosphines, the solution is reneutralized, saturated with salt, and extracted with chloroform, and the product is refractionated. One cycle is normally enough. Pure product is essentially odorless, very hygroscopic, and soluble in polar solvents. 

Analyses for the Saxitoxins. Early methods for analysis of the saxitoxins evolved from those used for toxin isolation and purification. The principal landmarks in the development of preparative separation techniques for the saxitoxins were 1) the employment of carboxylate cation exchange resins by Schantz et al. (82) 2) the use of the polyacrylamide gel Bio-Gel P2 by Buckley and by Shimizu (5,78) and 3) the development by Buckley of an effective TLC system, including a new solvent mixture and a new visualization technique (83). The solvent mixture, designated by Buckley as "E", remains the best for general resolution of the saxitoxins. The visualization method, oxidation of the saxitoxins on silica gel TLC plates to fluorescent degradation products with hydrogen peroxide and heat, is an adaptation of the Bates and Rapoport fluorescence assay for saxitoxin in solution. Curiously, while peroxide oxidation in solution provides little or no response for the N-l-hydroxy saxitoxins, peroxide spray on TLC plates is a sensitive test for all saxitoxin derivatives with the C-12 gemdiol intact. 

Chand R, Ince NH, Gogate PR, Bremner DH (2009) Phenol degradation using 20, 300 and 520 kHz ultrasonic reactors with hydrogen peroxide, ozone and zero valent metals. Sep Purif Technol 67 103-109... 

Sodium methoxide, 3-methyl-4-nitroanisole, diethyl oxalate, 30% hydrogen peroxide, 97% sodium hydride, methyl acetoacetate, sodium sulfate, 10% palladium on activated carbon, ammonium formate, and 2-nitrophenylacetic acid were purchased from Aldrich Chemical Company, Inc., and were used without further purification. 

Methylenecyclohexane oxide has been prepared by the oxidation of methylenecyclohexane with benzonitrile-hydrogen peroxide or with peracetic acid by treatment of 1-chlorocyclo-hexylmethanol with aqueous potassium hydroxide and by the reaction of dimethylsulfonium methylide with cyclohexanone. This reaction illustrates a general method for the conversion of ketones and aldehydes into oxiranes using the methylene-transfer reagent dimethyloxosulfonium methylide. The yields of oxiranes are usually high, and the crude products, in most cases, are of sufficient purity to be used in subsequent reactions (e.g., rearrangement to aldehydes) without further purification. 

Extraction, purification, and bleaching (with hydrogen peroxide) leave hemicellulose fibers softened, swollen, and with greatly enhanced amor-phism and adhesiveness, but with water retentivity (Gould et al., 1990) inferior to polysaccharides, although still quite high. The stability of hemicellulose dispersions is maximum at neutral pH. Dried fibers are difficult to redisperse. 

---