Hydrochloric acid, high purity

Samples should be stored in acid-washed linear polyethylene bottles 4mL of concentrated hydrochloric acid (high purity grade) should be added per 1000 mL of sample. No changes in germanic acid concentration have been detected in samples stored for several years at pH = 2. 

Gas chromatography or Hquid chromatography (23) are commonly used to measure impurities such as acetic, dichloroacetic, and trichloroacetic acids. High purity 99+% chloroacetic acid will contain less than 0.5% of either acetic acid or dichloroacetic acid. Other impurities that may be present in small amounts are water and hydrochloric acid. 

The metal is not attacked by hydrochloric acid, nor does it react with dilute nitric and sulfuric acids. High purity selenium reacts slowly with concentrated nitric acid. The crude metal, however, dissolves in cold concentrated nitric acid. 

DAG is treated with ethanol and hydrochloric acid in the presence of inert solvent, eg, chlorinated solvents, hydrocarbons, ketones, etc. The L-ascorbic acid precipitates from the mixture as it forms, minimising its decomposition (69). Cmde L-ascorbic acid is isolated through filtration and purified by recrystallization from water. The pure L-ascorbic acid is isolated, washed with ethanol, and dried. The mother Hquor from the recrystallization step is treated in the usual manner to recover the L-ascorbic acid and ethanol contained in it. The cmde L-ascorbic acid mother Hquor contains solvents and acetone Hberated in the DAG hydrolysis. The solvents are recovered by fractional distillation and recycled. Many solvent systems have been reported for the acid-catalyzed conversion of DAG to L-ascorbic acid (46). Rearrangement solvent systems are used which contain only the necessary amount of water required to give >80% yields of high purity cmde L-ascorbic acid (70). 

Cobalt(II) chloride hexahydrate [7791-13-1], C0CI2 6H20 is a deep red monoclinic crystalline material that deflquesces. It is prepared by reaction of hydrochloric acid with the metal, simple oxide, mixed valence oxides, carbonate, or hydroxide. A high purity cobalt chloride has also been prepared electrolyticaHy (4). The chloride is very soluble in water and alcohols. The dehydration of the hexahydrate occurs stepwise ... 

Zinc is relatively low in the electrochemical series and is widely regarded as an active metal. However, when high-purity zinc is placed in hydrochloric acid it will dissolve extremely slowly, if at all. It may be encouraged to... 

After 30 minutes the solid sulfinic acid is separated on a fritted-glass filter. The sulfinic acid is dissolved from the filter by a mixture of 750 ml. of ether and 750 ml, of methylene chloride. The solution is dried over calcium chloride and evaporated to dryness under reduced pressure (bath temperature 25°) (Note 5). The residue is suspended in 50 ml. of water, and small portions of dilute ammonia are added to the well-stirred suspension until it has a pH of 9 (Note 6). Insoluble impurities are separated by filtration, and 2-nitrobenzenesulfinic acid is precipitated from the filtrate by adding 5-ml. portions of 6N hydrochloric acid with cooling the sulfinic acid precipitated by each portion of acid is separately collected on a Buchner funnel (Note 7). The acid, a pale yellow solid, is dried on a clay plate in a vacuum desiccator over potassium hydroxide pellets, m.p. 120-125° (dec.), weight 9.4-14.9 g. (50-80%). If the 2-nitrobenzenesulfinic acid is to be used for the hydrogenation of the next step high purity is required, and it is generally advisable to reprecipitate the acid once more in the same way (Note 8). 

Surface modification reactions are used to improve the wettability of glass surfaces by polar stationary phases and to Improve the extent of deactivation by sllylation" [138-146,166]. Miaaiuua procedures have been investigated but only a few are in use. Of these, the most important reactions are etching by hydrogen chloride, leaching with aqueous hydrochloric acid, formation of whiskers and solution deposition of a layer of solid particles. Because of the high purity and thinness of the... 

For example, the industrial preparation of mineral acids, such as sulfuric, hydrochloric and nitric, inevitably leads to them containing small concentrations of metals as impurities. If the acid is to be used purely as an acid in a simple reaction, the presence of small amounts of metals is probably unimportant. If, however, the acid is to be used to digest a sample for the determination of trace metals by atomic absorption spectrometry, then clearly the presence of metallic impurities in the acid may have a significant effect on the results. For this latter application, high-purity acids that are essentially metal-free are required. 

Primary standards are stable chemical compounds that are available in high purity and which can be used to standardise the standard solutions used in titrations. Titrants such as sodium hydroxide or hydrochloric acid cannot be considered as primary standards since their purity is quite variable. So for instance sodium... 

---