Humidity types

Very dependent on external factors such as the type of incubation medium, temperature, oxidation, humidity, types of microbial populations and others. 

Requirements for space suits are more complex and frequently involve garments that can circulate water and/or air through the fibrous assembly. Laminated and/or coated garments with specific requirements to pressure, radiation, temperature, and humidity are more stmcturaHy complex as a textile product relative to the types of fibers used in this aerospace fabrication. 

A second type of uv curing chemistry is used, employing cationic curing as opposed to free-radical polymerization. This technology uses vinyl ethers and epoxy resins for the oligomers, reactive resins, and monomers. The initiators form Lewis acids upon absorption of the uv energy and the acid causes cationic polymerization. Although this chemistry has improved adhesion and flexibility and offers lower viscosity compared to the typical acrylate system, the cationic chemistry is very sensitive to humidity conditions and amine contamination. Both chemistries are used commercially. 

The cure rate of a sihcone sealant is dependent on the reactivity of the cross-linker, catalyst type, catalyst level, the diffusion of moisture into the sealant, and the diffusion of the leaving group out of the sealant. For one-part sealants, moisture diffusion is the controlling step and causes a cured skin to form on the exposed sealant surface and progress inward. The diffusion of moisture is highly dependent on the temperature and relative humidity conditions. 

The critical parameters of ethylene oxide steriliza tion are temperature, time, gas concentration, and relative humidity. The critical role of humidity has been demonstrated by a number of studies (11,18,19). Temperature, time, and gas concentration requirements are dependent not only on the bioburden, but also on the type of hardware and gas mixture used. If cycle development is not possible, as in the case of hospital steriliza tion, the manufacturer s recommendations should be followed. 

The hygroscopic and humectant properties of com symps are of great importance in many apphcations. Depending on the type of symp and on the specific conditions of temperature and humidity, the products may either resist or facihtate moisture loss or moisture absorption. The abihty to attract moisture or retard its loss increases with increasing DE value. Prevention of moisture pickup is more characteristic of symps having low DE values. 

Since surfactant-type antistats function by attracting atmospheric moisture to the plastic, the relative humidity (rh) has a significant effect on antistat performance (Fig. 6). Relative humidity also has an effect on charge generation (Table 7). 

Two types of mechanical-draft towers are in use today the forced-draft and the induced-draft. In the forced-draft tower the fan is mounted at the base, and air is forced in at the bottom and discharged at low velocity through the top. This arrangement has the advantage of locating the ran and drive outside the tower, where it is convenient for inspection, maintenance, and repairs. Since the equipment is out of the hot, humid top area of the tower, the fan is not subjected to corrosive conditions. However, because of the low exit-air velocity, the forced-draft tower is subjected to excessive recirculation of the humid... 

Performance data on some typical tray and compartment diyers are tabulated in Table 12-10. These indicate that an overall rate of evaporation of 0.0025 to 0.025 kg water/(s m") of tray area may be expected from tray and tray-truck diyers. The thermal efficiency of this type of diyer will vary from 20 to 50 percent, depending on the diying temperature used and the humidity of the exhaust air. In diying to very low moisture contents under temperature restrictions, the thermal efficiency may be in the order of 10 percent. The major operating cost for a tray diyer is the labor involved in loading and unloading the trays. About two labor-hours are required to load and unload a standard two-truck tray diyer. In addition, about one-third to one-fifth of a... 

Special provisions are laid down in lEC 60079-0 and lEC 60079-1 for motors required for such locations in view of fluctuating degrees of humidity and temperature. Such locations are defined with a surface temperature limit of 150°C where coal dust can form a layer, or 450°C where it is not expected to form a layer. Otherwise, other details are generally the same as for flameproof motors type Ex d , according to lEC 60079-1. For variations in length of paths, gaps, widths, creepage and clearance distances, the reader should consult these Standards. 

In humid and corrosive conditions, aluminium erodes faster than copper. These solid or hollow conductors connect the stipply side to the receiving end and are called bus ducts. They may be of the open type, stich as are used to feed a very high current tit very low voltage. A smelter unit is one such application. Btit nonnally they are housed in a sheet mettil enclostiie.. See Figtires 28.2(a) and 28.33(b). 

Because of their selectivity, molecular sieves offer advantages over silica gel, alumina or activated charcoal, especially in their very high affinity for water, polar molecules and unsaturated organic compounds. Their relative efficiency is greatest when the impurity to be removed is present at low concentrations. Thus, at 25° and a relative humidity of 2%, type 5A molecular sieves adsorb 18% by weight of water, whereas for silica gel and alumina the figures are 3.5 and 2.5% respectively. Even at 100° and a relative humidity of 1.3% molecular sieves adsorb about 15% by weight of water. 

---