High-pressure reinforced

Table 5.5 High-pressure reinforced TS laminates using different resins...

Pulp-like olefin fibers are produced by a high pressure spurting process developed by Hercules Inc. and Solvay, Inc. Polypropylene or polyethylene is dissolved in volatile solvents at high temperature and pressure. After the solution is released, the solvent is volatilised, and the polymer expands into a highly fluffed, pulp-like product. Additives are included to modify the surface characteristics of the pulp. Uses include felted fabrics, substitution in whole or in part for wood pulp in papermaking, and replacement of asbestos in reinforcing appHcations (56). 

The most commonly used reinforcement for high pressure decorative and industrial laminates is paper (qv). The strong substrate layers, or filler, are kraft paper. Kraft is a brown paper made from a sulfate pulp process (8). It consists of both short cellulose fibers from hardwoods and long fibers from conifers. The long fibers impart most of the wet strength required for resin saturation processes. 

The quantity of resin appHed to the reinforcing ply to achieve a state of full densification varies inversely with the laminating pressure. Therefore, high pressure laminates pressed at about 7 MPa (1000 psi) need only about 25—30% phenoHc resin in kraft paper, whereas low pressure (1 MPa = 145 psi) laminates need 50—60% resin in the reinforcing ply if all voids are to be filled in the final product. 

The largest segment of the CASE family of polyurethanes are elastomers. Cast polyurethane elastomers reached a new dimension when high pressure impingement mixing led to reaction injection molding (RIM). This technology is used widely in the automotive industry, and reinforced versions (RRIM) and stmctural molded parts (SRIM) have been added in more recent years. 

Concrete nuclear reactor vessels, of the order of magnitude of 15-m (50-ft) inside diameter and length, have inner linings of steel which confine the pressure. After fabrication of the liner, the tubes for the cables or wires are put in place and the concrete is poured. High-strength reinforcing steel is used. Because there are thousands of reinforcing tendons in the concrete vessel, there is a statistical factor of safety. The failure of 1 or even 10 tendons would have little effec t on the overall structure. 

Corrosion usually results in a leak or failure of a support because a vessel or support gets too thin. It is then not strong enough to withstand the pressure or load. However, rust can cause failure in another way. It occupies about seven times the volume of the steel from which it was formed. V/hen rust occurs between two plates that have been bolted or riveted together, a high pressure develops. This can force the plates apart or even break the bolts or rivets (see Section 9.1.2 g). Corrosion of the reinforcement bars in concrete can cause the concrete to crack and break away. 

In the reinforced RIM (RRIM) process a dry reinforcement preform is placed in a closed mold. Next a reactive plastic system is mixed under high pressure in a specially designed mixing head. Upon mixing, the reacting liquid flows at low pressure through a runner system to fill the mold cavity, impregnating the reinforcement in the process. Once the mold cavity is filled, the plastic quickly completes its reaction. The complete cycle time required to produce a molded thick product can be as little as one minute. 

Because of high capital costs and potential HE of steel pipelines for high-pressure hydrogen transport, the investigation of fiber reinforcement or other plastic composites as substitutes for steels is one of the major R D tasks within the DOE hydrogen delivery program. The purpose of the work is to achieve reduction in installation costs, better reliability, and safer operation of hydrogen pipelines. 

The effects of processing will be illustrated by considering injection moulding of a semicrystalline polymer. The molten plastic is injected into the mould under high pressure and temperature. The edges of the mould retard flow and cool more rapidly, leading to a boundary layer of high shear, which in semicrystalline polymers leads to orientation of the polymer chains and of short fibre reinforcements parallel to the direction of flow. At the centre the structure is less oriented. Where two separate flow streams meet, there is a... 

Reinforced plastics differ from high-pressure laminates in that little or no pressure is employed. For instance, in making formed shapes, impregnated reinforcing material is cut to a desired shape, the various layers are added to a mold, which is then heated. This process is favored over the high-pressure process because of the use of a simpler, lower cost mold and production of strain-free products. 

---