Halides, aryl reaction with metals

Aryl and alkenyl halides undergo reactions with metals such as Zn, Mg, and Li to give products where the C-X bond is replaced with a C-metal bond. The best-known metal insertion reaction is the Grignard reaction, which uses Mg. Lithiation requires two equivalents of Li, because each Li supplies only one electron, but the Grignard and zinc insertion reactions require only one equivalent. The rate of insertion is strongly dependent on X, with I > Br 5S> Cl, corresponding to the strength of the C-X bonds. 

Organocadmium compounds can be prepared from Grignard reagents or organo-lithium compounds by reaction with Cd(II) salts.180 They can also be prepared directly from alkyl, benzyl, and aryl halides by reaction with highly reactive cadmium metal generated by reduction of Cd(II) salts.181... 

Thallium(III), particularly as the trifluoroacetate salt, is also a reactive electrophilic metallating species, and a variety of synthetic schemes based on arylthallium intermediates have been devised.75 Arylthallium compounds are converted to chlorides or bromides by reaction with the appropriate cupric halide.76 Reaction with potassium iodide gives aryl iodides.77 Fluorides are prepared by successive treatment with potassium fluoride and boron trifluoride.78 Procedures for converting arylthallium compounds to nitriles and phenols have also been described.79... 

Aryl halides reaction with metal cyanides, often with another transition metal catalyst, to give aryl nitriles (aryl cyanides). Aryl halides react with Zn(CN)2 and a palladium catalyst, for example, to give the aryl nitrile. Similarly, aryl iodides react with CuCN and a palladium catalyst to give the aryl nitrile. Potassium cyanide (KCN) reacts in a similar manner with a palladium catalyst. " Sodium cyanide has been used with a copper catalyst and 20% The reaction of aryl iodides... 

The general synthesis of aryl xanthates is described by Schussler et al. 12). It follows from the ability of thallium(I) xanthates to undergo metathetical reactions with metal halides in absolute ethanol (Reaction 4). The thallium(I) precursors could be obtained with phenol... 

Other transition metals than palladium have been reported to activate aryl halides for reactions with alkenes [e.g., Ni(0), Cu(I), Co(I),f Rh(I) (Wilkinson s catalyst) and Ir(I) (Vaska s complex]. 

The aryl- and alkyllithiums can be prepared from the corresponding halides by reaction with lithium metal. A mole of lithium halide is produced as a by-product... 

COUPLING REACTIONS OF ARYL HALIDES AND SULFONATES WITH METAL COMPLEXES AND ACTIVE METALS... 

Chapter 3 - Coupling reactions of aryl halides and sulfonates with metal complexes and active metals. Pages 43-81... 

Cross coupling of aryl halides involves one metallation step (e.g. with Li) followed by exchange with copper halide and reaction with Ar iodide [19]. 

Perfluoroalkyl or -aryl halides undergo oxidative addition with metal vapors to form nonsolvated fluonnated organometallic halides and this topic has been die subject of a review [289] Pentafluorophenyl halides react with Rieke nickel, cobalt, and iron to give bispentafluorophenylmetal compounds, which can be isolated in good yields as liquid complexes [290] Rieke nickel can also be used to promote the reaction of pentafluorophenyl halides with acid halides [297] (equation 193)... 

The synthetic applicability is rather limited, due to the various side-reactions observed, such as eliminations and rearrangement reactions. The attempted coupling of two different alkyl halides in order to obtain an unsymmetrical hydrocarbon, usually gives the desired product in only low yield. However the coupling reaction of an aryl halide with an alkyl halide upon treatment with a metal (the Wurtz-Fittig reaction) often proceeds with high yield. The coupling of two aryl halides usually does not occur under those conditions (see however below ) since the aryl halides are less reactive. 

This method ensures the deposition of very reactive metal nanoparticles that require no activation steps before use. We shall review here the following examples of catalytic reactions that are of interest in line chemical synthesis (a) the hydrogenation of substituted arenes, (b) the selective hydrogenation of a, 3-unsaturated carbonyl compounds, (c) the arylation of alkenes with aryl halides (Heck reaction). The efficiency and selectivity of commercial catalysts and of differently prepared nanosized metal systems will be compared. 

As noted in Section 11.2.2, nucleophilic substitution of aromatic halides lacking activating substituents is generally difficult. It has been known for a long time that the nucleophilic substitution of aromatic halides can be catalyzed by the presence of copper metal or copper salts.137 Synthetic procedures based on this observation are used to prepare aryl nitriles by reaction of aryl bromides with Cu(I)CN. The reactions are usually carried out at elevated temperature in DMF or a similar solvent. 

Transition metal-catalyzed transformations are of major importance in synthetic organic chemistry [1], This reflects also the increasing number of domino processes starting with such a reaction. In particular, Pd-catalyzed domino transformations have seen an astounding development over the past years with the Heck reaction [2] - the Pd-catalyzed transformation of aryl halides or triflates as well as of alkenyl halides or triflates with alkenes or alkynes - being used most often. This has been combined with another Heck reaction or a cross-coupling reaction [3] such as Suzuki, Stille, and Sonogashira reactions. Moreover, several examples have been published with a Tsuji-Trost reaction [lb, 4], a carbonylation, a pericyclic or an aldol reaction as the second step. 

---