Graphite natural deposits

The diamond is found in natural deposits in many parts of the world. Also, it can be synthesized from graphite or other carbonaceous materials. Graphite can be converted to diamond under high temperatures (about 1,400°C) and very high pressure (in the range 4,000-5,000 atm) in the presence of a metal catalyst such as iron or nickel. Presence of trace impurities can impart different coloration to diamonds. For example, introducing trace boron or nitrogen causes blue or yellow coloration. 

Crystalline carbon exists in natural deposits in three crystalline modifications a and 8-graphite and diamond. Synthetic graphites contain only the a-form, from which the (3 can be made by mechanical working. This introduces the possibility of the transformation a p during a hardness test. Localized transformation from diamond to a metallic carbon 8-graphite could also be considered, but in this case a radical rearrangement of covalent bond hybridization would be required from sp to sp + p such that time would be a problem. 

The largest quantity of commercial pyrolytic graphite is produced in large, inductively heated furnaces in which natural gas at low pressure is used as the source of carbon. Deposition temperatures usually range from 1800 to 2000°C on a deposition substrate of fine-grain graphite. 

Table 3 summarizes the world s production of natural graphite for 1986—1988 (9). As of 1990, the deposits of significant commercial interest were limited to those of Sri Lanka (Ceylon), Madagascar, Mexico, Canada, Brazil, Germany, Austria, the RepubUc of Korea, Norway, Russia, Ukraine, People s RepubUc of China, and Zimbabwe. 

As in the case of graphite-supported catalysts, some metal particles were also encapsulated by the deposited carbon (Fig. 4). However, the amount of encapsulated metal was much less. Differences in the nature of encapsulation were observed. Almost all encapsulated metal particles on silica-supported catalysts were found inside the tubules (Fig. 4(a)). The probable mechanism of this encapsulation was precisely described elsewhere[21 ]. We supposed that they were catalytic particles that became inactive after introduction into the tubules during the growth process. On the other hand, the formation of graphite layers around the metal in the case of graphite-supported catalysts can be explained on the basis of... 

Most black pigments are made of carbon black formed by depositing carbon from a smoky flame of natural gas on a metal surface. Lampblack is made similarly by burning oik Bone blacks are made from charred bones. Graphite occurs naturally or can be prepared from coal in electric furnaces. Mineral blacks come from shale, peat, and coal dust. Iron oxide blacks are found in nature or prepared. Blue lead sulfate is a pigment for priming. Of these, carbon black is su[XTinr. 

Graphite is commonly produced by CVD and is often referred to as pyrolytic graphite. It is an aggregate of graphite crystallites, which have dimensions (L ) that may reach several hundred nm. It has a turbostratic structure, usually with many warped basal planes, lattice defects, and crystallite imperfections. Within the aggregate, the crystallites have various degrees of orientation. When they are essentially parallel to each other, the nature and the properties of the deposit closely match that of the ideal graphite crystal. 

The future remains bright for the use of carbon materials in batteries. In the past several years, several new carbon materials have appeared mesophase pitch fibers, expanded graphite and carbon nanotubes. New electrolyte additives for Li-Ion permit the use of low cost PC based electrolytes with natural graphite anodes. Carbon nanotubes are attractive new materials and it appears that they will be available in quantity in the near future. They have a high ratio of the base plane to edge plain found in HOPG. The ultracapacitor application to deposit an electronically conductive polymer on the surface of a carbon nanotube may be the wave of the future. 

Lithium-ion batteries high energy density purified natural graphite carbon coated silicon graphite/metal composites chemical vapor deposition. 

For illustrative purposes, the process of deposition of Si onto graphite is being used as an example. The 15 pm natural graphite precursors were introduced into the industrial size chemical vapor deposition reactor, where a thermal decomposition of silane (SiH4) into the silicon and hydrogen was taking place under inert gas in accordance with the equation (1) ... 

TEG-Si, TEG-Sn and dispersed natural graphite-Sn have been prepared by thermal vacuum deposition under continuos mixing. 

Previous studies focusing on deposition of Cu [6, 15] or Ni [16] coatings and deposits on natural and synthetic graphics relied on an electroless plating method [25]. In this method many different chemical solutions are used in multiple steps to treat the graphite surface, such as... 

The cycling improvement for the Cu-metallized graphite over the pristine graphite was also observed by K. Guo et al. [15] in their study of electroless Cu deposited on graphite cycled in a lithium cell with a 20% PC blend electrolyte. Also, they recorded a rate capability improvement in their Cu graphite material as well. At a current density of 1.4 mA/cm2, the cell achieved about 60% ( 200 mAh/g) of the charge capacity measured at 0.14 mA/cm2, compared to about 30% ( 100 mAh/g) for the non-treated pristine natural graphite cell [15]. 

---