Free radicals—continued

This formation of Cl free radicals continues until all chlorine is consumed. Chloroform and carhon tetrachloride are formed in a similar way hy reaction of CHCI2 and CCI3 free radicals with chlorine. 

Candau and co-workers were the first to address the issue of particle nu-cleation for the polymerization of AM [13, 14] in an inverse microemulsion stabilized by AOT. They found that the particle size of the final microlatex (d 20-40 nm) was much larger than that of the initial monomer-swollen droplets (d 5-10 nm). Moreover, each latex particle formed contained only one polymer chain on average. It is believed that nucleation of the polymer particle occurs for only a small fraction of the final nucleated droplets. The non-nucleated droplets also serve as monomer for the growing particles either by diffusion through the continuous phase and/or by collisions between droplets. But the enormous number of non-nucleated droplets means that some of the primary free radicals continuously generated in the system will still be captured by non-nucleated droplets. This means that polymer particle nucleation is a continuous process [ 14]. Consequently, each latex particle receives only one free radical, resulting in the formation of only one polymer chain. This is in contrast to the large number of polymer chains formed in each latex particle in conventional emulsion polymerization, which needs a much smaller amount of surfactant compared to microemulsion polymerization. 

Antioxidants also increase oxidative stability. These bind active free radicals, thus preventing initiation of new reaction chains. If free radicals continue to form, due to the presence of oxygen and trace metals, eventually all the antioxidant will react, and the autocatalytic sequence will develop without hindrance. 

Traditional Free Radical Continuous Initiation, compositionally different... 

One can note the continuous increase of the reacted diamine quantity with this parameter of the mechanical regime, a consequence of the free radical continuous generation at the newly formed surfaces. 

It is assumed that the new free radical continues the kinetic chain and that its activity is similar to that of the radical whose growth was stopped. Thus, the transfer process will have no influence upon the overall polymerisation kinetics apart from causing the DP of the polymer produced to be less than it would have been in the absence of any transfer reactions. The effect of transfer reactions on DP is governed by the Mayo equation ... 

The curing mechanism of this type of adhesive is a free radical reaction. Thus, the usual steps in such a reaction also take place in these types of adhesives. The adhesive has to contain a free radical initiator, the breakdown of which into free radicals is the initiation step for the reaction. The next step is the propagation step in which the free radical initiator species reacts with the monomer and then the initiator/monomer reaction product (also a free radical) continues the reaction until all of the monomer is consumed as part of the polymer. Next steps are termination reactions in which free radical ends of the polymer find each other and react, terminating the reaction. Otherwise, the propagating free radical can undergo disproportionation, also resulting in termination. 

Termination steps (Section 4 17) Reactions that halt a chain reaction In a free radical chain reaction termination steps consume free radicals without generating new radicals to continue the chain... 

While this reaction with solvent continues to provide free radicals, these may be less reactive species than the original initiator fragments. We shall have more to say about the transfer of free-radical functionality to solvent in Sec. 6.8. 

Most commercial processes involve copolymerization of ethylene with the acid comonomer followed by partial neutralization, using appropriate metal compounds. The copolymerization step is best carried out in a weU-stirred autoclave with continuous feeds of all ingredients and the free-radical initiator, under substantially constant environment conditions (22—24). Owing to the relatively high reactivity of the acid comonomer, it is desirable to provide rapid end-over-end mixing, and the comonomer content of the feed is much lower than that of the copolymer product. Temperatures of 150—280°C and pressures well in excess of 100 MPa (1000 atm) are maintained. Modifications on the basic process described above have been described (25,26). When specific properties such as increased stiffness are required, nonrandom copolymers may be preferred. An additional comonomer, however, may be introduced to decrease crystallinity (10,27). 

Figure 4c illustrates interfacial polymerisation encapsulation processes in which the reactant(s) that polymerise to form the capsule shell is transported exclusively from the continuous phase of the system to the dispersed phase—continuous phase interface where polymerisation occurs and a capsule shell is produced. This type of encapsulation process has been carried out at Hquid—Hquid and soHd—Hquid interfaces. An example of the Hquid—Hquid case is the spontaneous polymerisation reaction of cyanoacrylate monomers at the water—solvent interface formed by dispersing water in a continuous solvent phase (14). The poly(alkyl cyanoacrylate) produced by this spontaneous reaction encapsulates the dispersed water droplets. An example of the soHd—Hquid process is where a core material is dispersed in aqueous media that contains a water-immiscible surfactant along with a controUed amount of surfactant. A water-immiscible monomer that polymerises by free-radical polymerisation is added to the system and free-radical polymerisation localised at the core material—aqueous phase interface is initiated thereby generating a capsule sheU (15). 

LDPE, also known as high pressure polyethylene, is produced at pressures ranging from 82—276 MPa (800—2725 atm). Operating at 132—332°C, it may be produced by either a tubular or a stirred autoclave reactor. Reaction is sustained by continuously injecting free-radical initiators, such as peroxides, oxygen, or a combination of both, to the reactor feed. 

Although primary and secondary alkyl hydroperoxides are attacked by free radicals, as in equations 8 and 9, such reactions are not chain scission reactions since the alkylperoxy radicals terminate by disproportionation without forming the new radicals needed to continue the chain (53). Overall decomposition rates are faster than the tme first-order rates if radical-induced decompositions are not suppressed. 

Oxidation. AH polyamides are susceptible to oxidation. This involves the initial formation of a free radical on the carbon alpha to the NH group, which reacts to form a peroxy radical with subsequent chain reactions leading to chain scission and yellowing. As soon as molten nylon is exposed to air it starts to discolor and continues to oxidize until it is cooled to below 60°C. It is important, therefore, to minimize the exposure of hot nylon to air to avoid discoloration or loss of molecular weight. Similarly, nylon parts exposed to high temperature in air lose their properties with time as a result of oxidation. This process can be minimized by using material containing stabilizer additives. 

Styryl free radicals simultaneously initiate micelle nuclei at points of high fumarate concentration. The micelles continue to expand, interacting with free... 

Anionic polymerization offers fast polymerization rates on account of the long life-time of polystyryl carbanions. Early studies have focused on this attribute, most of which were conducted at short reactor residence times (< 1 h), at relatively low temperatures (10—50°C), and in low chain-transfer solvents (typically benzene) to ensure that premature termination did not take place. Also, relatively low degrees of polymerization (DP) were typically studied. Continuous commercial free-radical solution polymerization processes to make PS, on the other hand, operate at relatively high temperatures (>100° C), at long residence times (>1.5 h), utilize a chain-transfer solvent (ethylbenzene), and produce polymer in the range of 1000—1500 DP. 

One of the key benefits of anionic PS is that it contains much lower levels of residual styrene monomer than free-radical PS (167). This is because free-radical polymerization processes only operate at 60—80% styrene conversion, whereas anionic processes operate at >99% styrene conversion. Removal of unreacted styrene monomer from free-radical PS is accompHshed using continuous devolatilization at high temperature (220—260°C) and vacuum. This process leaves about 200—800 ppm of styrene monomer in the product. Taking the styrene to a lower level requires special devolatilization procedures such as steam stripping (168). 

Continuous Polymerization. A typical continuous flow diagram for the vinyl acetate polymerisation is shown in Figure 12. The vinyl acetate is fed to the first reactor vessel, in which the mixture is purged with an inert gas such as nitrogen. Alternatively, the feed may be purged before being introduced to the reactor (209). A methanol solution containing the free-radical initiator is combined with the above stream and passed directiy and continuously into the first reactor from which a stream of the polymerisation mixture is continuously withdrawn and passed to subsequent reactors. More initiator can be added to these reactors to further increase the conversion. 

Chlorine atoms obtained from the dissociation of chlorine molecules by thermal, photochemical, or chemically initiated processes react with a methane molecule to form hydrogen chloride and a methyl-free radical. The methyl radical reacts with an undissociated chlorine molecule to give methyl chloride and a new chlorine radical necessary to continue the reaction. Other more highly chlorinated products are formed in a similar manner. Chain terrnination may proceed by way of several of the examples cited in equations 6, 7, and 8. The initial radical-producing catalytic process is inhibited by oxygen to an extent that only a few ppm of oxygen can drastically decrease the reaction rate. In some commercial processes, small amounts of air are dehberately added to inhibit chlorination beyond the monochloro stage. 

Continuous chlorination of benzene at 30—50°C in the presence of a Lewis acid typically yields 85% monochlorobenzene. Temperatures in the range of 150—190°C favor production of the dichlorobenzene products. The para isomer is produced in a ratio of 2—3 to 1 of the ortho isomer. Other methods of aromatic ring chlorination include use of a mixture of hydrogen chloride and air in the presence of a copper—salt catalyst, or sulfuryl chloride in the presence of aluminum chloride at ambient temperatures. Free-radical chlorination of toluene successively yields benzyl chloride, benzal chloride, and benzotrichloride. Related chlorination agents include sulfuryl chloride, tert-huty hypochlorite, and /V-ch1orosuccinimide which yield benzyl chloride under the influence of light, heat, or radical initiators. 

Chlorination of Methane. Methane can be chlorinated thermally, photochemicaHy, or catalyticaHy. Thermal chlorination, the most difficult method, may be carried out in the absence of light or catalysts. It is a free-radical chain reaction limited by the presence of oxygen and other free-radical inhibitors. The first step in the reaction is the thermal dissociation of the chlorine molecules for which the activation energy is about 84 kj/mol (20 kcal/mol), which is 33 kJ (8 kcal) higher than for catalytic chlorination. This dissociation occurs sufficiendy rapidly in the 400 to 500°C temperature range. The chlorine atoms react with methane to form hydrogen chloride and a methyl radical. The methyl radical in turn reacts with a chlorine molecule to form methyl chloride and another chlorine atom that can continue the reaction. The methane raw material may be natural gas, coke oven gas, or gas from petroleum refining. 

For Hquid fuels, ignition delay times are of the order 50 ]ls at 700 K and 10 ]ls at 800 K. At low temperatures most of the ignition delay is the result of slow, free-radical reactions, and a distinction between the initiation and explosion periods within the ignition delay time can be made. With increasing ignition temperature for a given mixture, these times become comparable and at temperatures as high as 1500 K, both times may be of the order of lO " s. Consequently, the reaction zone in the flame of a mixture is observed to be one continuous event (12—14). 

---