Fluorided catalyst, first

Prsparation. The first preparation of VF dates back to 1901 and the reaction of zinc with l,l-difluoro-2-bromoethane [359-07-9] (3). Phenylmagnesium bromide in ether and potassiiun iodide solution can replace the metal for de-halogenation (4,5). Most approaches to VF s3uithesis have employed reactions of acetylene [74-86-2] with hydrogen fluoride (HF) either directly (5-8) or utilizing a catalyst (6,9-13) based on merciuy or aluminum (6,9,12,14). In another process, an acetylene/HF mixture is passed over a mercuric chloride or fluoride catalyst, which also produces vinyUdene fluoride and difluoroethane as by-products (10). Another S3uithesis (11) consists of two steps in which 1,1-difluoroethane (DFE) is... 

At atmospheric pressure vinyl fluoride (VF) is a colorless gas with an etheral odor. Its boiling point is — 72.2°C, its critical temperature Tc=54.7°C, and its critical pressure Pc = 51.7 atm. It is flammable at air between the limits of 2.6 and 21.7% VF by volume and an ignition temperature of 400 °C. A toxie effect is found at 20% VF by volume and above [456,457], The first reported preparation was by Swartz [451] in 1901. VF was found after the reaction between l,l-difluoro-2-bromoethane and zinc. Later the pyrolysis of 1,1-difiuoroethane at 725 °C over a chromium fluoride catalyst [462] or at 400 °C in the presence of oxygen [463] are described. 

Organic fluorine compounds were first prepared in the latter part of the nineteenth century. Pioneer work by the Belgian chemist, F. Swarts, led to observations that antimony(Ill) fluoride reacts with organic compounds having activated carbon—chlorine bonds to form the corresponding carbon—fluorine bonds. Preparation of fluorinated compounds was faciUtated by fluorinations with antimony(Ill) fluoride containing antimony(V) haUdes as a reaction catalyst. 

Vlayl fluoride [75-02-5] (VF) (fluoroethene) is a colorless gas at ambient conditions. It was first prepared by reaction of l,l-difluoro-2-bromoethane [359-07-9] with ziac (1). Most approaches to vinyl fluoride synthesis have employed reactions of acetylene [74-86-2] with hydrogen fluoride (HF) either directly (2—5) or utilizing catalysts (3,6—10). Other routes have iavolved ethylene [74-85-1] and HF (11), pyrolysis of 1,1-difluoroethane [624-72-6] (12,13) and fluorochloroethanes (14—18), reaction of 1,1-difluoroethane with acetylene (19,20), and halogen exchange of vinyl chloride [75-01-4] with HF (21—23). Physical properties of vinyl fluoride are given ia Table 1. 

Zirconium tetrafluoride [7783-64-4] is used in some fluoride-based glasses. These glasses are the first chemically and mechanically stable bulk glasses to have continuous high transparency from the near uv to the mid-k (0.3—6 -lm) (117—118). Zirconium oxide and tetrachloride have use as catalysts (119), and zirconium sulfate is used in preparing a nickel catalyst for the hydrogenation of vegetable oil. Zirconium 2-ethyIhexanoate [22464-99-9] is used with cobalt driers to replace lead compounds as driers in oil-based and alkyd paints (see Driers and metallic soaps). 

With Formaldehyde. The sulfuric acid cataly2ed reaction of formaldehyde [50-00-0] with carbon monoxide and water to glycoHc acid [79-14-1] at 473 K and 70 MPa (700 atm) pressure was the first step in an early process to manufacture ethylene glycol [107-21-1]. A patent (58) has described the use of Hquid hydrogen fluoride as catalyst, enabling the reaction to be carried out at 298 K and 7 MPa (70 atm) (eq. 18). 

A proposed mechanism for silyl ether displacement is shown in Scheme 6.14. In the first step, the fluoride anion converts the trimethyl siloxy group into a phe-nolate salt. In the following step, the phenolate anion attacks the activated fluoro monomer to generate an ether bond. The amount of catalyst required is about 0.1-0.3 mol%. Catalyst type and concentration are crucial for this reaction. 

The role of Lewis acids in the formation of oxazoles from diazocarbonyl compounds and nitriles has primarily been studied independently by two groups. Doyle et al. first reported the use of aluminium(III) chloride as a catalyst for the decomposition of diazoketones.<78TL2247> In a more detailed study, a range of Lewis acids was screened for catalytic activity, using diazoacetophenone la and acetonitrile as the test reaction.<80JOC3657> Of the catalysts employed, boron trifluoride etherate was found to be the catalyst of choice, due to the low yield of the 1-halogenated side-product 17 (X = Cl or F) compared to 2-methyI-5-phenyloxazole 18. Unfortunately, it was found that in the case of boron trifluoride etherate, the nitrile had to be used in a ten-fold excess, however the use of antimony(V) fluoride allowed the use of the nitrile in only a three fold excess (Table 1). 

Other reactions not described here are formal [3 -i- 2] cycloadditions of a,p-unsaturated acyl-fluorides with allylsilanes [116], or the desymmetrization of meso epoxides [117]. For many of the reactions shown above, the planar chiral Fe-sandwich complexes are the first catalysts allowing for broad substrate scope in combination with high enantioselectivities and yields. Clearly, these milestones in asymmetric Lewis-base catalysis are stimulating the still ongoing design of improved catalysts. 

Following the reactions in Scheme 4, the olefin 13 would have to be generated before the formation of the 7r-crotyl species 2. Because the amount of the catalyst present is usually small as compared to the amount of product formed (1000 moles of product/mole catalyst), the quantity of 13 produced will not be significant and should be readily separable from the desired product. In the special case when crotyl chloride is used as the activator, hexadiene can be produced during the very first cycle of reaction, i.e., 13 = 1,4-hexadiene. Among the organic halides, the chloride derivatives are the most effective activators. Bromides are somewhat effective, while fluorides and iodide are rather ineffective (77). 

In the first case, SENAs in the presence of various catalysts (primarily salts containing the fluoride anion) generate the corresponding a-nitro carbanions, which are poorly solvated in aprotic solvents and, consequently, rapidly react with substrates R3— Y = X to give functionalized nitro compounds through the transition state A. 

Detal [Detergent alkylation] A process for making detergent alkylate, i.e., alkyl aromatic hydrocarbons such as linear alkyl benzenes, as intermediates for the manufacture of detergents, by reacting C10-C13 olefins with benzene in a fixed bed of an acid catalyst. Developed by UOP and CEPSA as a replacement for their Detergent Alkylate process, which uses liquid hydrogen fluoride as the catalyst. Demonstrated in a pilot plant in 1991 and first commercialized in Canada in 1996. Offered by UOP. 

The first promising asymmetric aldol reactions through phase transfer mode will be the coupling of silyl enol ethers with aldehydes utilizing chiral non-racemic quaternary ammonium fluorides,1371 a chiral version of tetra-n-butylammonium fluoride (TBAF). Various ammonium and phosphonium catalysts were tried138391 in the reaction of the silyl enol ether 41 of 2-methyl-l-tetralone with benzaldehyde, and the best result was obtained by use of the ammonium fluoride 7 (R=H, X=F) derived from cinchonine,1371 as shown in Scheme 14. 

A ubiquitous co-catalyst is water. This can be effective in extremely small quantities, as was first shown by Evans and Meadows [18] for the polymerisation of isobutene by boron fluoride at low temperatures, although they could give no quantitative estimate of the amount of water required to co-catalyse this reaction. Later [11, 13] it was shown that in methylene dichloride solution at temperatures below about -60° a few micromoles of water are sufficient to polymerise completely some decimoles of isobutene in the presence of millimolar quantities of titanium tetrachloride. With stannic chloride at -78° the maximum reaction rate is obtained with quantities of water equivalent to that of stannic chloride [31]. As far as aluminium chloride is concerned, there is no rigorous proof that it does require a co-catalyst in order to polymerise isobutene. However, the need for a co-catalyst in isomerisations and alkylations catalysed by aluminium bromide (which is more active than the chloride) has been proved [34-37], so that there is little doubt that even the polymerisations carried out by Kennedy and Thomas with aluminium chloride (see Section 5, iii, (a)) under fairly rigorous conditions depended critically on the presence of a co-catalyst - though whether this was water, or hydrogen chloride, or some other substance, cannot be decided at present. 

The first study with an oxygen compound which was sufficiently rigorous to provide evidence on the question of co-catalysis was that of Farthing and Reynolds [61]. They showed that 3,3-bischloromethyl oxetan could be polymerised in methyl chloride solution by boron fluoride only in the presence of water. Tater, Rose [62] obtained kinetic evidence for the need for a co-catalyst in the system oxetan—boron fluoride—methyl chloride, and he interpreted the low reaction rate when no water was added as due to residual water he also showed that water and a hydroxyl-terminated polymer could act as co-catalysts. 

---