Ensure - meaning

Ensuring means making certain and you can t make certain without having control over that which causes the results. 

Ensure means of controlling pressure and alarm systems, which go off when the thresholds are exceeded, allowing an automatic decrease in pressure. 

Ensuring means of escape inciuding corridors and finai exit doors are not obstructed particu-iariy with combustibie materiai >- Ensuring aii doors required to provide emergency egress are cieariy marked and operate as they shouid... 

This might he worthwhile if the FEED-BYPRODUCT separation is expensive. To use a purge, the FEED and BYPRODUCT must be adjacent to each other in order of volatility (assuming distillation is used as the means of separation). Of course, care should be taken to ensure that the resulting increase in concentration of BYPRODUCT in the reactor does not have an adverse effect on reactor performance. Too much BYPRODUCT might, for example, cause a deterioration in the performance of the catalyst. 

It is well established that GO approximation leads to aceurate results if both the source and the observation points are not close to the interface. In practice, this means that both points must be distant from the interface of at least one wavelength. This condition is always fulfilled for the source point. For the field-point, the accuracy of the solution is ensured if the above condition is completed, as shown by comparing exact and approximate results [5]. 

For an ideal gas and a diathemiic piston, the condition of constant energy means constant temperature. The reverse change can then be carried out simply by relaxing the adiabatic constraint on the external walls and innnersing the system in a themiostatic bath. More generally tlie initial state and the final state may be at different temperatures so that one may have to have a series of temperature baths to ensure that the entire series of steps is reversible. 

In order to encode displacement as opposed to average position, the gradient is applied in such a maimer as to ensure that ). Generally, this means applying gradient pulses in bipolar pairs or applying uni-... 

Most TB approaches are not charge self-consistent. This means that they do not ensure that the charge derived from the wavefiinctions yields the effective potential assumed in their calculation. Some methods have been developed which yield charge densities consistent with the electronic potential [14, H and 16]. 

After return to the Commander window, the reaction retrieval may be executed separately 629 Dicls-Aldcr reactions between aliphatic dienes and cyclic dicno-pliiles are found. This partial result can be narrowed down by restricting tlie reaction conditions by means of the fact editor, The search field codes for the yield and the temperature can be found to be RX.NYD and RX.T, respectively, either by browsing the database structure or by applying the Find option, as described in the first example. To ensure that the retrieved reaction conditions belong to the same experiment, both search terms must be connected by means of the PROXIMITY operator. Before the retrieval is started, the option "Refine results in... 

A typical molecular dynamics simulation comprises an equflibration and a production phase. The former is necessary, as the name imphes, to ensure that the system is in equilibrium before data acquisition starts. It is useful to check the time evolution of several simulation parameters such as temperature (which is directly connected to the kinetic energy), potential energy, total energy, density (when periodic boundary conditions with constant pressure are apphed), and their root-mean-square deviations. Having these and other variables constant at the end of the equilibration phase is the prerequisite for the statistically meaningful sampling of data in the following production phase. 

The heating of the vessels is accomplished by means of a small bath or a micro-Bunsen burner. The vessel can be clamped at such a distance from the burner that the contained liquid boils gently under reflux. Smooth boiling is ensured by the addition of 1-2 minute pieces of unglazed porcelain, or of a short piece of melting-point tubing open at both ends. 

Dissolve 15 ml. (15-4 g.) of aniline in a mixture of 40 ml. of concentrated hydrochloric acid and 40 ml. of water contained in a 250 ml. conical flask. Place a thermometer in the solution, immerse the flask in a mixture of ice and water, and cool until the temperature of the stirred solution reaches 5°. Dissolve I2 5 g. of powdered sodium nitrite in 30 ml. of water, and add this solution in small quantities (about 2-3 ml. at a time) to the cold aniline hydrochloride solution, meanwhile keeping the latter well stirred by means of a thermometer. Heat is evolved by the reaction, and therefore a short interval should be allowed between consecutive additions of the sodium nitrite, partly to allow the temperature to fall again to 5°, and partly to ensure that the nitrous acid formed reacts as completely as possible with the aniline. The temperature must not be allowed to rise above 10°, otherwise appreciable decomposition of the diazonium compound to phenol will occur on the other hand, the temperature... 

Into a 2-litre, three-necked flask, fitted with a separatory funnel, a mechanical stirrer and a reflux condenser, place a hot solution of 200 g. of potassium hydroxide in 200 ml. of water. Stir the solution and add slowly 200 g. of ethyl n-butylmalonate (Section 111,154). A vigorous reaction occurs and the solution refluxes. When all the ester has been added, boil the solution gently for 2-3 hours, i.e., until hydrolysis is complete a test portion should dissolve completely in water. Dilute with 200 ml. of water and distil oflF 200 ml. of liquid in order to ensure the complete removal of the alcohol formed in the hydrolysis (1) it is best to connect the flask by means of a wide delivery tube to a condenser set for downward distillation (compare Fig. II, 41, 1 but with a mercury-sealed stirrer in the centre neck). Replace the separatory funnel and the reflux condenser. 

These dyes possess two independent chromophoric chains of even methine (neutro) and uneven methine (cyanine) fixed on a central ketometbylene nucleus. The methylene reactive group is first used for the neutrocyanine synthesis in position 5. the, quaternization of which can ensure a subsequent polymethine synthesis in position 2 of a cationic dye by ordinary means (Scheme 58). As indicated, this quaternized neutrocyanine (37) may as well give another neutrocyanine. 

---