Dyed resists

Such contradictory claims regarding the effectiveness of the dye in improving a line width control appear to reflect a complex interdependence of the various materials and processing parameters that is not adequately accounted for in the simulation programs. In general, dyed resists are believed to provide improved control of dimensions in lines printed over highly reflective substrates, and several vendors have made dyed resist formulations... 

Oxide films on aluminum are produced by anodi2ing in a chromic acid solution. These films are heavier than those produced by chemical conversion and thinner and more impervious than those produced by the more common sulfuric acid anodi2ing. They impart exceptional corrosion resistance and paint adherence to aluminum and were widely used on military aircraft assembHes during World War II. The films may be dyed. A typical anodi2ing bath contains 50 to 100 g/L CrO and is operated at 35—40°C. The newer processes use about 20 volts dc and adjust the time to obtain the desired film thickness (184). 

The most popular coloration method is to apply the dyes continuously, usually by padding, but printing, spray jet, and droplet appHcations are used. In order to obtain patterned effects, chemical or physical resisting agents can be appHed first, and deep and normal dyeing nylon and basic dyeable nylon blends can be used. In the latter case the basic dyeable nylon is dyed with cationic dyes. Carpets can be printed in an analogous method to other textiles and this process is more popular in Europe than the continuous appHcation techniques used in the United States. 

Wax Printing. This is a special case of resist printing and widely used in African designs. Wax is first printed onto cotton fabric to give a patterned effect, and the fabric is then dyed. The wax resists penetration of the dye and reserves the fabric. The wax is then removed by either alkaU washing or solvent when it is also recovered for future use. Other colors can then be printed, if so desired, on the nondyed areas. A2oic dyes or reactive dyes can be used for this. 

Z. 5-25-Y, large huhhles = AA = 0.42 (NG..) Wi dy > 0.25 cm Dr luterfacial area 6 fig volume dy [E] Use with arithmetic concentration difference, ffg = fractional gas holdup, volume gas/total volume. For large huhhles, k is independent of bubble size aud independent of agitation or liquid velocity. Resistance is entirely in liquid phase for most gas-liquid mass transfer. [79][91] p. 452 [109] p. 119 [114] p. 249... 

The first use of PAs was in fiber applications, in which fibers were produced by melt spinning. These materials have a high strength and good wear resistance and can be easily dyed. The tension stiffening effect of the PA melt made the production of fibers witii homogeneous thickness possible. 

Atmospheric ozone has also been reported as causing fading of certain dyes in some countries [425,426] diallyl phthalate (10.182) used as a carrier in the dyeing of cellulose triacetate fibres, is said to be an effective ozone inhibitor [427]. Nylon, especially when dyed with certain amino-substituted anthraquinone blue acid dyes, can also be susceptible to ozone fading [428,429]. Selection of ozone-resistant dyes is obviously the best counteractive measure, although hindered phenols (10.161) and hindered amines (10.162) are said to provide some protection. 

PTT fibers and yams have bulk, resiliency, stretch-recovery, softness, hand and drape, properties which are similar to those of nylons and much better than those of PET. Such materials are inherently resistant to most stains which are acidic in nature because they not have dye sites. They also have a lower static propensity than nylons. PTT fibers are dyed with disperse dyes but at a lower temperature than PET because of the polymer s lower Tt. The combinations of these properties are attractive to carpet and textile manufacturers in some applications where PTT could replace nylon or PET. PTT also offers the potential of creating new fiber products by using the unique combinations of these properties not found in either nylon or PET alone. 

To make cut pile carpets, two strands of BCF yarns are twisted together and heat-set with steam using a Superba heat setting machine at 135-145 °C or at 175-195 °C when heat-set with super-heated steam in a Suessen. An experimental design experiment [94] showed the higher the heat set temperature, then the lower is the bulk of the final carpet, but there is an increase in the tip definition and walk performance. The tufted carpets are then dyed with disperse dyes at atmospheric boil [95] in a continuous or a batch process. PTT carpets showed excellent resiliency in walk test experiments, equivalent to a nylon and much better than both PET and polypropylene, had lower static charge of <3.5 kV, and were resistant to coffee, mustard, betadine, red acid dyes and other stains [96],... 

Hallaert DY, Jaspers A, van Noesel CJ et al (2008) c-Abl kinase inhibitors overcome CD40-mediated drug resistance in CLL implications for therapeutic targeting of chemoresis-tant niches. Blood 112 5141-5149... 

---