Diallyldimethyl ammonium chloride

Copolymer of diallyldimethyl ammonium chloride and quatemized anuno alkylmethacrylates and (meth)acrylic esters (e.g., 2-ethylhexylacrylate) OiW [791,1478,1479]... [Pg.331]

Copolymer of diallyldimethyl ammonium chloride and vinyl trimethoxysilane WiO ... [Pg.331]

Poly(diallyldimethyl ammonium chloride) Alkoxylated fatty oil OiW [787]... [Pg.331]

A combination of aluminum chlorohydrate and a polyamine, such as poly (diallyldimethyl ammonium chloride), in aqueous solution is effective at elevated temperatures for an oil-in-water emulsion [787]. [Pg.338]

Copolymer of Diallyldimethyl Ammonium Chloride and Vinyl Trimethoxysilane... [Pg.338]

In particular, copolymers of diallyldimethyl ammonium chloride and vinyl trimethoxysilane will have a molecular weight in the range from 100,000 to 1,000,000 Dalton. [Pg.338]

Polymers in which the quarternary nitrogen atom is part of a five- or six-membered ring comprise the second class of polymers. The ring forms part of the polymer backbone as indicated by the second and third polymer repeat units given in Table I. The member of this class cited in several patents is poly(diallyldimethyl-ammonium chloride) abbreviated poly(DMDAAC). [Pg.211]

To enhance the shelf life of finished paper product, the step 1 product was applied below its critical micelle concentration (CMC). Materials additized above the CMC formed insoluble gels when aged for 8 days at 73°C. The CMC ranges was determined using glyoxalated poly(vinylamide-co-diallyldimethyl-ammonium chloride) containing 90 wt% vinylamide and are provided in Table 1. [Pg.50]

Fig. 6. Cyclopolymerization of diallyldimethyl ammonium chloride and chain structures of the resulting polymers...

AChE was sandwiched with poly(diallyldimethyl-ammonium chloride) layers on the surface of CNTs. The OP biosensor thus developed was used to detect paraoxon (Figure 55.7) as low as 4 x 10 M with a 6 min response time in flow injection analysis. A high stability of the sensors was also a merit of this biosensor no deterioration in the response was observed after 1 week of eontinuous use of the sensor. Only a 15% deerease in the aetivity of the enzyme was observed after 3 weeks, though the authors... [Pg.841]

Also used are Polyquaternium-16, a copolymer of vinylpyrrolidone and quater-nized vinylimidazole and Polyquaternium-6, a homopolymer of diallyldimethyl-ammonium chloride. [Pg.386]

Luminol, poIy(diallyldimethyl ammonium chloride) and chitosan were obtained... [Pg.301]

Hollow fibers and spheres of zeolite (labeled as HFZ and HSZ, respectively) were successfully fabricated using carbon fibers and polystyrene (PS) spheres as templates respectively, through layer-by-layer technique, coupled with removal of the templates by calcination. The optimum performance conditions to obtain these kinds of materials were systematically studied. The wall thickness and composition of these novel materials can be readily tailored by varying the number of nanozeolite/PDDA (poly(diallyldimethyl ammonium chloride)) deposition cycles and zeolite type used, respectively. The properties of these novel materials were characterized by means of XRD, IR and SEM. [Pg.296]

Figure 2 Schematic representation of various modes of attachment of catalyticaUy active complexes to soluble polymers covalent binding to a PPI dendrimer (upper left) electrostatic binding to linear poly(diallyldimethyl-ammonium chloride) (upper right) physisorption in a unimolecular micelle of amphiphillically modified hyperbranched polyglycerol (lower left) specific hydrogen-bonding to a urea functionalized PPI dendrimer.

Caruso et al. [69] reported the preparation of negatively charged polystyrene latex particles (640 nm diameter) armored with a nanocomposite multilayer of Si02 nanoparticles (Ludox TM-40 26 4nm diameter) and poly(diallyldimethyl-ammonium chloride) (PDADMAC). These two components were sequentially adsorbed onto the surface of the polystyrene latex spheres (see Fig. 11), after adsorption of a precursor polyelectrolyte multilayer film of PDADMAC/... [Pg.33]

Poly(diallyldimethyl ammonium chloride)/ poly (sodium styrene sulfonate) and poly(ethyleneimine)/polyacrylic acid filled with aluminum and zirconium oxide AN-maleic anhydride copolymer membrane... [Pg.196]

Acrylamide/dimethyidiallyl ammonium chloride copolymer Diallyidimethyl ammonium chloride with acrylamide N,N-Dimethyl-N-2-propenyl-2-propen-1-aminium chloride, polymer with 2-propenamide Poly (acrylamide-co-diallyldimethyl ammonium chloride) 2-Propen-1-aminium, N,N-dimethyl-N-2-propenyl-, chloride, polymer with 2-propenamide Quatemium-41 Classification Polymeric quaternary ammonium salt... [Pg.3557]

Methacryloxy-ethyl trimethylammonium chloride/AM copolymer, diallyldimethyl ammonium chloride copolymer... [Pg.274]

L1T Litmanovich, E.A., Chemikova, E.V., Stoychev, G.V., and Zakharchenko, S.O., Unusual phase behavior of the mixture of poly(acryhc acid) and poly(diallyldimethyl ammonium chloride) in acidic media. Macromolecules, 43, 6871, 2010. [Pg.716]

Monomers with multiple, nonconjugated double bonds Diallyldimethyl ammonium chloride Diisopropenyl benzene Divinyl benzene Ethyleneglycol dimethacrylate Trimethylolpropane triacrylate Penterythritol teraacrylate Specialty monomers with reactive groups Carboxyl acid Acrylic acid Methacrylic acid Maleic acid Itaconic acid Hydroxyl... [Pg.3749]

PDAD-MAC Poly(diallyldimethyl ammonium chloride) TATB l,3,5-Triamino-2,4,6- trinitrobenzene... [Pg.784]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...