Polystyrene-latex particles

The relationship between the increase in contact radius due to plastic deformation and the corresponding increase in the force required to detach submicrometer polystyrene latex particles from a silicon substrate was determined by Krishnan et al. [108]. In that study, Krishnan measured the increase in the contact area of the partieles over a period of time (Fig. 7a) and the corresponding decrease in the percentage of particles that could be removed using a force that was sufficient to remove virtually all the particles initially (Fig. 7b). 

A very similar effect of the surface concentration on the conformation of adsorbed macromolecules was observed by Cohen Stuart et al. [25] who studied the diffusion of the polystyrene latex particles in aqueous solutions of PEO by photon-correlation spectroscopy. The thickness of the hydrodynamic layer 8 (nm) calculated from the loss of the particle diffusivity was low at low coverage but showed a steep increase as the adsorbed amount exceeded a certain threshold. Concretely, 8 increased from 40 to 170 nm when the surface concentration of PEO rose from 1.0 to 1.5 mg/m2. This character of the dependence is consistent with the calculations made by the authors [25] according to the theory developed by Scheutjens and Fleer [10,12] which predicts a similar variation of the hydrodynamic layer thickness of adsorbed polymer with coverage. The dominant contribution to this thickness comes from long tails which extend far into the solution. 

Serizawa and Akashi [95] analyzed the monolayer adsorption of polystyrene latex particles with cationic polyvinylamine grafted on their surface, while Serizawa et al. [96,97] used commercial anionic latex particles. Both types of particles were adsorbed on polyelectrolyte-coated substrates previously prepared by alternating adsorption of cationic and anionic polyelectrolytes such as polyallylamine hydrochloride (PAH) and polystyrene sulfonate sodium salt (PSS) according to the method described by Decher [164]. Using... 

Adsorption-Desorption Behavior of Polyvinyl Alcohol on Polystyrene Latex Particles... 

The adsorption of fully and partially hydrolyzed (88%) polyvinyl alcohol (PVA) on 190-1lOOnm monodisperse polystyrene latex particles was investigated. The effect of molecular weight was investigated for 190 nm-size particles using the serum replacement adsorption and desorption methods. The adsorption density at the adsorption-isotherm plateau followed the relationships for the fully hydrolyzed... 

Figure 2. Adsorption isotherms of HPC-M, HEC-H and PVAonto polystyrene latex particles at 1 8 °C.

Figure 3. Temperature dependences of saturated adsorption (As) of HPC onto polystyrene latex particles.

Studies on orthokinetic flocculation (shear flow dominating over Brownian motion) show a more ambiguous picture. Both rate increases (9,10) and decreases (11,12) compared with orthokinetic coagulation have been observed. Gregory (12) treated polymer adsorption as a collision process and used Smoluchowski theory to predict that the adsorption step may become rate limiting in orthokinetic flocculation. Qualitative evidence to this effect was found for flocculation of polystyrene latex, particle diameter 1.68 pm, in laminar tube flow. Furthermore, pretreatment of half of the latex with polymer resulted in collision efficiencies that were more than twice as high as for coagulation. 

A similar technique has been applied to the generation of monodisperse suspensions in water. This type of method was first used in medical field and then widely used to spray monodisperse solid particles such as polystyrene latex particles. Aerosols of solutes have also been produced by atomizing solutions of salt, sugar or methylene blue dye dissolved in water. In practical operations, a low concentration of solid particles in a solvent is recommended in order to avoid possible agglomeration of suspensions in the solvent. 

Figure 8.14 CLSM images showing the initial development of the microstructure of a phase-separated mixed biopolymer system (25.5 wt% sugar, 31.4 wt% glucose syrup, 7 wt% gelatin, and 4 wt% oxidized starch pH = 5.2, low ionic strength) containing 0.7 wt% polystyrene latex particles (d32 = 0.3 pm). The sample was quenched from 90 to 1 °C, held at 1 °C for 10 min, heated to 40 °C at 6 °C min-1, and observed at 40 °C for various times (a) 2 min, (b) 4 min, (c) 8 min, and (d) 16 min. White regions are rich in colloidal particles. Reproduced from Firoozmand et ai (2009) with permission.

FIG. 1.8 Electron micrograph of cross-linked monodisperse polystyrene latex particles. The latex is a commercial product (d = 0.500 jun) sold as a calibration standard. (Photograph courtesy of R. S. Daniel and L. X. Oakford, California State Polytechnic University, Pomona, CA.)... 

FIG. 13.4 Stereo pairs of colloidal dispersions generated using computer simulations, (a) Polystyrene latex particles at a volume fraction of 0.13 with a surface potential of 50 mV. The 1 1 electrolyte concentration is 10 7 mol/cm3. The structure shown is near crystallization. (The solid-black and solid-gray particles are in the back and in the front, respectively, in the three-dimensional view.) (b) A small increase in the surface potential changes the structure to face-centered cubic crystals. (Redrawn with permission from Hunter 1989.)... 

Polystyrene latex particles were coagulated by the addition of Ba(N03)2. The number of dispersed particles deposited onto a planar polystyrene surface was determined 15 min after the addition of salt by optical microscopy. The light microscope does not permit the aggregation of the deposited particles to be determined subsequent examination by the electron microscope gives this information. Clint et al. obtained the following results ... 

Garvey et al.85) made a similar sedimentation study on poly(vinyl alcohol) adsorbed on polystyrene latex particles. Adsorbance of the polymer was also measured. Both the thickness of the adsorbed layer and the adsorbance increased linearly with the square root of the molecular weight. The volume occupied by a polymer molecule in the adsorbed layer was approximately equal to that of the effective hydrodynamic sphere in bulk solution. However, the measured values of LH were greater than the hydrodynamic diameters of the polymer coils in solution. Thus, it may be concluded that adsorbed poly(vinyl alcohol) assumes a conformation elongated in the direction normal to the surface. 

Gesler, R. M. and Garvin, P. J. (1973) The biological effects of polystyrene latex particles administered intravenously to rats, a collaborative stuByill. Parent. Drug Assoc., 27 101-113. 

The useful range of the transmission electron microscope for particle size measurement is c. 1 nm-5 p,m diameter. Owing to the complexity of calculating the degree of magnification directly, this is usually determined by calibration using characterised polystyrene latex particles or a diffraction grating. 

Figure 3.2 Electron micrographs, (a) Shadowed polystyrene latex particles (x 50 000), (b) Shadowed silver chloride particles i x 15 000)... 

Figure 7.7 Zeta potentials (calculated from electrophoretic mobility data) relating to particles of different ionogenic character plotted as a function of pH in acetate-veronal buffer at constant ionic strength of 0.05 mol dm 3, (a) Hydrocarbon oil droplets, (b) Sulphonated polystyrene latex particles, (c) Arabic acid (carboxylated polymer) adsorbed on to oil droplets, (d) Serum albumin adsorbed on to oil droplets...

Figure 9. Diagram illustrating the effect of anionic, cationic, and nonionic surfactants on anionic polystyrene latex particles...

Figure 14. Changes in stability of an anionic polystyrene latex (particle diameter = 52.7 nm) admixed with a cationic latex (particle diameter = 43.4 nm). N+ and N. = the number concentration of the cationic and anionic latices, respectively (-A-) 10 3 mol dm 3 sodium chloride solution (-O-) 2 X 10 3 mol dm 3 sodium...

Figure 2. Variation of electrophoretic mobility in distilled water with pH for polystyrene latex particles with different surface groups (1) 520 sulfate (2) 520 carboxyl (3) 520 hydroxyl (4) LS-1010-E sulfate (5) LS-1010-E hydroxyl.

---