Physical deterioration

Inspections consist of a visual check of the fire protection systems by qualified personnel to ensure the system is available for immediate use. Visual checks should be made using a checklist. The inspection should verify that the fixed and portable equipment is ready to be operated. The associated devices, fittings, piping, and valving are inspected to ensure they have not been tampered with and that there is no obvious deterioration, physical damage, or condition to prevent operation. Documentation of the visual inspections may vary from... 

In the processing of plastic masses the destruction is traditionally considered as a negative factor deteriorating physical and mechanical properties of products and manufacturers try to avoid it in every possible way. Mechanical destruction of molten polymers takes place, primarily, under the action of shear strains effectuating the tension of macromolecules 65-661 in this case, molecules with a high molecular mass... 

The various chemical and physical processes that play a role ia the deterioration of art objects are not restricted to the present, even though the contemporary environment has contributed significantly to the rate of decay. Revered masterpieces have lost splendor throughout the ages. Indeed, from textual evidence, it is known how artists ia the Renaissance restored works of art from Classical times. These restorers of past centuries attempted to return the object to its original appearance. The fallacy of that idea Hes ia the fact that they could not know the exact original appearance of the work, ie, immediately after its creation therefore, they restored the object according to their subjective opinions. 

The arrest of deterioration and the prevention of its recurrence has higher priority than restoration. Thus, identification of the causes of a problem and the design of measures to stabilize and consoHdate the object are primary considerations. Removal of the symptoms and restoration of the visual appearance comes only after the physical iategrity has beea safeguarded. 

The principal functions of food packaging are to protect the food contents from physical damage, losses, or deterioration, and to faciUtate distribution from processor to consumer. Food packaging also must attractively identify the product and must perform these functions at minimum system cost because the package itself has no intrinsic value to the consumer. In 1992, food packaging represented about 57% of the United States more than 70 biUion packaging industry. 

Ton-exchange resins are used repeatedly in a cyclic manner over many years, and deterioration of both physical and chemical properties can be anticipated. Comparison of the properties of used resin with those of new resin is helpfiil to learning more about the nature and cause of deterioration (12). Corrective action frequendy extends the life of the resin. Comparison of properties must always be made with the resin in the same ionic form. 

The actual time required for poly-L-lactide implants to be completely absorbed is relatively long, and depends on polymer purity, processing conditions, implant site, and physical dimensions of the implant. For instance, 50—90 mg samples of radiolabeled poly-DL-lactide implanted in the abdominal walls of rats had an absorption time of 1.5 years with metaboHsm resulting primarily from respiratory excretion (24). In contrast, pure poly-L-lactide bone plates attached to sheep femora showed mechanical deterioration, but Httie evidence of significant mass loss even after four years (25). 

Reaction to Heat and Fire. The physical and chemical properties of wood, like those of any organic material, are subject to deterioration. 

Sources Subject to Prevention of Significant Deterioration (PSD) Sources subject to PSD regulations (40 CFR, Sec. 52.21, Aug. 7, 1980) are major stationary sources and major modifications located in attainment areas and unclassified areas. A major stationaiy source was defined as any source hsted in Table 25-4 with the potential to emit 100 tons per year or more of any pollutant regulated under the Clean Air Act (CAA) or any other source with the potential to emit 250 tons per year or more of any CAA pollutant. The potential to emit is defined as the maximum capacity to emit the pollutant under apphcable emission standards and permit conditions (after apphcation of any air pollution control equipment) excluding secondaiy emissions. A major modification is defined as any physical or operational change of a major stationaiy source producing a significant net emissions increase of any CAA pollutant (see Table 25-5). 

Deterioration Permanent adverse change in the physical properties of a plastic. 

Weathering. This generally occurs as a result of the combined effect of water absorption and exposure to ultra-violet radiation (u-v). Absorption of water can have a plasticizing action on plastics which increases flexibility but ultimately (on elimination of the water) results in embrittlement, while u-v causes breakdown of the bonds in the polymer chain. The result is general deterioration of physical properties. A loss of colour or clarity (or both) may also occur. Absorption of water reduces dimensional stability of moulded articles. Most thermoplastics, in particular cellulose derivatives, are affected, and also polyethylene, PVC, and nylons. 

Most sleep deprivation experiments have used mentally and physically healthy young adults. For other types of individuals, particularly older people for whom the sleep function deteriorates in general, and also for "real world" conditions, sleep deprivation may be more significant. 

Hot spot formation witliin tlie reactor can result in catalyst breakdown or physical deterioration of tlie reactor vessel." If tlie endothermic cyanide reaction has ceased (e.g., because of poor catalyst performance), the reactor is likely to overheat. Iron is a decomposition catalyst for hydrogen cyanide and ammonia under the conditions present in the cyanide reactor, and e. posed iron surfaces in the reactor or reactor feed system can result in uncontrolled decomposition, which could in turn lead to an accidaital release by overheating and overpressure. 

---