Cumene synthesis process

Fig. 1. UOP catalytic condensation process for cumene synthesis. R = reactor RECT = rectifier DP = depropanizer RC = recycle column ...

More than 95% of the cumene produced is used as feedstock for the production of phenol (qv) and its coproduct acetone (qv). The cumene oxidation process for phenol synthesis has been growing in popularity since the 1960s and is prominent today. The first step of this process is the formation of cumene hydroperoxide [80-15-9]. The hydroperoxide is then selectively cleaved to phenol [108-95-2] and acetone [67-64-1/ in an acidic environment (21). 

Phenol is the starting material for numerous intermediates and finished products. About 90% of the worldwide production of phenol is by Hock process (cumene oxidation process) and the rest by toluene oxidation process. Both the commercial processes for phenol production are multi step processes and thereby inherently unclean [1]. Therefore, there is need for a cleaner production method for phenol, which is economically and environmentally viable. There is great interest amongst researchers to develop a new method for the synthesis of phenol in a one step process [2]. Activated carbon materials, which have large surface areas, have been used as adsorbents, catalysts and catalyst supports [3,4], Activated carbons also have favorable hydrophobicity/ hydrophilicity, which make them suitable for the benzene hydroxylation. Transition metals have been widely used as catalytically active materials for the oxidation/hydroxylation of various aromatic compounds. 

Since zeolite catalysts are successfully introduced in the refining and petrochemical industries, it is not surprising that most of the recent advances concern incremental improvements of existing processes with the development of new generations of catalysts (e.g., dewaxing, ethylbenzene and cumene synthesis). The number of newer applications is much more limited, for example, direct synthesis of phenol from benzene and aromatization of short-chain alkanes, etc. However, both the improvement and development of processes contribute significantly to environmental advances. 

Treybal, in his book Liquid Extraction [1], works equilibrium material balances with triangular coordinates. The most unique and simple way to show three-phase equilibrium is a triangular diagram (Fig. 7.1), which is used for extraction unit operation in cumene synthesis plants [2], In this process benzene liquid is used as the solvent to extract acetic acid (the solute) from the liquid water phase (the feed-raffinate). The curve D,S,P,F,M is the equilibrium curve. Note that every point inside the triangle has some amount of each of the three components. Points A,... 

Current zeolite catalysts already operate at process temperatures that require minimal external heat addition. Heat integration and heat management will be of increasing concern at the lower benzene to propylene ratios because the cumene synthesis reaction is highly exothermic (AHf= -98 kJ/mole). Recycle, particularly in the alkylation reactor, is likely to become increasingly important as a heat management strategy. The key will be how to limit the build-up of byproducts and feed impurities in these recycle loops, particularly as manufacturers seek cheaper and consequently lower quality feedstocks. As in the case of ethylbenzene, process and catalyst innovations will have to develop concurrently. 

There is also the prospect of increased demand for some of the cumene byproducts such as diisopropylbezene (DIPB). The production of diphenols from DIPB is important for synthesis of resorcinol (from meta-DIPB) and hydroquinone (from para-DIPB). It is likely that the market may soon see the introduction of cumene based processes that specifically produce these isomers with high degrees of selectivity. 

Although SPA remains a viable catalyst for cumene synthesis, it has several important limitations 1) cumene yield is limited to about 95% because of the oligomerization of propylene and the formation of heavy alkylate by-products 2) the process requires a relatively high benzene/propylene (B/P) molar feed ratio on the order of 7/1 to maintain such a cumene yield and 3) the catalyst is not regenerable and must be disposed of at the end of each short catalyst cycle. Also, in recent years, producers have been given increasing incentives for better cumene product quality to improve the quality of the phenol, acetone, and especially a-methylstyrene (e.g., cumene requires a low butylbenzene content) produced from the downstream phenol units. 

FIGURE 9.28 Synthesis tree for carbide-cumene peroxidation process. 

FIGURE 9.33 Synthesis tree for Wacker-cumene peroxidation process. 

PROPENE The major use of propene is in the produc tion of polypropylene Two other propene derived organic chemicals acrylonitrile and propylene oxide are also starting materials for polymer synthesis Acrylonitrile is used to make acrylic fibers (see Table 6 5) and propylene oxide is one component in the preparation of polyurethane polymers Cumene itself has no direct uses but rather serves as the starting material in a process that yields two valuable indus trial chemicals acetone and phenol... 

The most widely used industrial synthesis of phenol is based on isopropylbenzene (cumene) as the starting material and is shown m the third entry of Table 24 3 The eco nomically attractive features of this process are its use of cheap reagents (oxygen and sulfuric acid) and the fact that it yields two high volume industrial chemicals phenol and acetone The mechanism of this novel synthesis forms the basis of Problem 24 29 at the end of this chapter... 

Sales demand for acetophenone is largely satisfied through distikative by-product recovery from residues produced in the Hock process for phenol (qv) manufacture. Acetophenone is produced in the Hock process by decomposition of cumene hydroperoxide. A more selective synthesis of acetophenone, by cleavage of cumene hydroperoxide over a cupric catalyst, has been patented (341). Acetophenone can also be produced by oxidizing the methylphenylcarbinol intermediate which is formed in styrene (qv) production processes using ethylbenzene oxidation, such as the ARCO and Halcon process and older technologies (342,343). 

The three-step cumene process, including the liquid-phase reactions and using sulfuric acid, is energy-consuming, environmentally unfavorable and disadvantageous for practical operation the process also produces as an unnecessary byproduct acetone, stoichiometrically. Furthermore, the intermediate, cumene hydroperoxide, is explosive and cannot be concentrated in the final step, resulting in a low one-path phenol yield, ( 5%, based on the amount of benzene initially used). Thus, direct phenol synthesis from benzene in one-step reaction with high... 

The related manufacture of cumene (isopropylbenzene) through the alkylation of benzene with propylene is a further industrially important process, since cumene is used in the synthesis of phenol and acetone. Alkylation with propylene occurs more readily (at lower temperature) with catalysts (but also with hydrogen fluoride and acidic resins) similar to those used with ethylene, as well as with weaker acids, such as supported phosphoric acid (see further discussion in Section 5.5.3). 

In conclusion no catalysts with good performances (>5% conversion and >50% selectivity, simultaneously) have been discovered to date. New selective catalysts for direct phenol synthesis from benzene with 02 are essential for the novel industrial process replacing the cumene process - there are many problems to be resolved. 

This case study deals with the design and simulation of a medium size plant of lOOkton cumene per year. The goal is performing the design by two essentially different methods. The first one is a classical approach, which handles the process synthesis and energy saving with distinct reaction and separation sections. In the second alternative a more innovative technology is applied based on reactive distillation. 

Process Economics Program Report SRI International. Menlo Park, CA, Isocyanates IE, Propylene Oxide 2E, Vinyl Chloride 5D, Terephthalic Acid and Dimethyl Terephthalate 9E, Phenol 22C, Xylene Separation 25C, BTX, Aromatics 30A, o-Xylene 34 A, m-Xylene 25 A, p-Xylene 93-3-4, Ethylbenzene/Styrene 33C, Phthalic Anhydride 34B, Glycerine and Intermediates 58, Aniline and Derivatives 76C, Bisphenol A and Phosgene 81, C1 Chlorinated Hydrocarbons 126, Chlorinated Solvent 48, Chlorofluorocarbon Alternatives 201, Reforming for BTX 129, Aromatics Processes 182 A, Propylene Oxide Derivatives 198, Acetaldehyde 24 A2, 91-1-3, Acetic Acid 37 B, Acetylene 16A, Adipic Acid 3 B, Ammonia 44 A, Caprolactam 7 C, Carbon Disulfide 171 A, Cumene 92-3-4, 22 B, 219, MDA 1 D, Ethanol 53 A, 85-2-4, Ethylene Dichloride/Vinyl Chloride 5 C, Formaldehyde 23 A, Hexamethylenediamine (HMDA) 31 B, Hydrogen Cyanide 76-3-4, Maleic Anhydride 46 C, Methane (Natural Gas) 191, Synthesis Gas 146, 148, 191 A, Methanol 148, 43 B, 93-2-2, Methyl Methacrylate 11 D, Nylon 6-41 B, Nylon 6,6-54 B, Ethylene/Propylene 29 A, Urea 56 A, Vinyl Acetate 15 A. 

Catalysis (27-30) which allows for the direct oxidation of benzene to produce phenol. Economic analyses have shown that these are attractive only in specific instances where, for example, a cheap source of N20 is available. Nevertheless, these developments have shown that direct oxidation is possible and further innovations in this area should probably be expected. The demands for acetone and phenol have generally tended to follow each other. However, as bisphenol A becomes an even more important end use for phenol and acetone, there will be a need for a separate source of phenol. The synthesis of bisphenol A requires two moles of phenol for every one mole of acetone, while the peroxidation of cumene produces one mole of each. Still, processes such as the direct oxidation of benzene are unlikely to have a major impact on cumene demand in the short term since there are competing processes such as Mitsui s for converting acetone back to propylene. 

---