Cracking resistance

Safe fatigue life testing for crack resistance. 

Measurement of the fatigue fractures depth during bench tests for crack resistance. 

In the sheeting market, the low density polyethylenes are less important than the high density resins. The high density resins have excellent chemical resistance, stress-crack resistance, durabiUty, and low temperature properties which make them ideal for pond liners, waste treatment faciUties, and landfills. In thicker section, HMW-HDPE sheet makes good containers, trays, tmck-bed liners, disposable items, and concrete molds. The good durabiUty, abrasion resistance, and light weight are critical elements for its selection. 

Flexural modulus increases by a factor of five as crystallinity increases from 50 to 90% with a void content of 0.2% however, recovery decreases with increasing crystallinity. Therefore, the balance between stiffness and recovery depends on the appHcation requirements. Crystallinity is reduced by rapid cooling but increased by slow cooling. The stress—crack resistance of various PTFE insulations is correlated with the crystallinity and change in density due to thermal mechanical stress (118). 

The high MV resia is used as liners for process equipmeat. Its melt viscosity is significantly higher than that of other resias and therefore it is unsuitable for conventional iajection molding. Stress-crack resistance and mechanical properties are superior to those of the other three products (52)... 

A combination of excellent chemical and mechanical properties at elevated temperatures results in rehable, high performance service to the chemical processing and related industries. Chemical inertness, heat resistance, toughness and flexibiUty, stress-crack resistance, excellent flex life, antistick characteristics, Htfle moisture absorption, nonflammability, and exceptional dielectric properties are among the characteristics of these resins. 

Duplex stainless steels (ca 4% nickel, 23% chrome) have been identified as having potential appHcation to nitric acid service (75). Because they have a lower nickel and higher chromium content than typical austenitic steels, they provide the ductabdity of austenitic SS and the stress—corrosion cracking resistance of ferritic SS. The higher strength and corrosion resistance of duplex steel offer potential cost advantages as a material of constmction for absorption columns (see CORROSION AND CORROSION CONTROL). 

In addition to the semicrystalline nylons, which comprise the vast majority of commercial resins, nylon is also available in an amorphous form that gives rise to transparency and improved toughness at the expense of high temperature properties and chemical stress crack resistance. Table 2 shows the properties of some different polyamide types. 

Resistance to Chemical Environments and Solubility. As a rule, amorphous plastics are susceptible, to various degrees, to cracking by certain chemical environments when the plastic material is placed under stress. The phenomenon is referred to as environmental stress cracking (ESC) and the resistance of the polymer to failure by this mode is known as environmental stress cracking resistance (ESCR). The tendency of a polymer to undergo ESC depends on several factors, the most important of which are appHed stress, temperature, and the concentration of the aggressive species. 

Stress cracking resistance is substantially enhanced in the presence of reinforcement such as glass fibers. 

For reasons that are not fiiUy understood, PPSF exhibits generally improved compatibiUty characteristics over either PSF or PES in a number of systems. An example of this is blends of PPSF with polyaryletherketones (39,40). These blends form extremely finely dispersed systems with synergistic strength, impact, and environmental stress cracking resistance properties. Blends of PPSF with either PSF or PES are synergistic in the sense that they exhibit the super-toughness characteristic of PPSF at PSF or PES contents of up to 35 wt % (33,34). The miscibility of PPSF with a special class of polyimides has been discovered and documented (41). The miscibility profile of PPSF with high temperature (T > 230° C) polysulfones has been reported (42). 

Monoethano1 amine-containing formulations can be used to make polycarbonate molds with good dyeabiUty and crack resistance (186). 

Until the 1960s, reclaimed mbber was an important raw material in molded and extmded mbber products, eg, tires, mbber mats, and hard mbber battery cases. With the advent of vinyl, other plastics, and less expensive oil-extended synthetic polymers, reclaimed mbber sales stabilized and decreased. In 1973, the oil embargo and rising energy costs increased costs of the energy-intensive mbber reclaiming process to the point where they matched virgin polymer costs. Increased radial tire production required crack resistance that could not be provided by reclaimed mbber compounds (46). 

Four modes of characterization are of interest chemical analyses, ie, quaUtative and quantitative analyses of all components mechanical characterization, ie, tensile and impact testing morphology of the mbber phase and rheology at a range of shear rates. Other properties measured are stress crack resistance, heat distortion temperatures, flammabiUty, creep, etc, depending on the particular appHcation (239). 

Sulfide Stress Cracking Resistant Metallic Materialfor OilField Equipment, NACE Standard MR-01-75, 1980 rev.. Technical Practices Committee, National Association of Corrosion Engineers, Houston, Tex., 1980. 

Siace these masses of polycrystaUine diamond possess extensive diamond-to-diamond bonding, they have, ia contrast to siagle-crystal diamond, excellent crack resistance, siace any crack that begias ia oae crystal oa an easy cracking plane (parallel to an octahedral face) is halted by neighboring crystals that are unfavorably oriented for their propagation. 

Flex cracking resistance Very good Good Good Good Good... 

NACE Publication 1F166 Sulfide Cracking-Resistant Metallic Materials for Valves for Production and Pipeline Service," Materials Protection, Sept. 1966. 

The very low density materials (VLDPEs) introduced in the mid-1980s are generally considered as alternatives to plasticised PVC (Chapter 12) and ethylene-vinyl acetate (EVA) plastics (see Chapter 11). They have no volatile or extractable plasticisers as in plasticised PVC nor do they have the odour or moulding problems associated with EVA. Whilst VLDPE materials can match the flexibility of EVA they also have better environmental stress cracking resistance, improved toughness and a higher softening point. 

The homopolymer finds a variety of uses, as an adhesive component, as a base for chewing gum, in caulking compounds, as a tackifier for greases, in tank linings, as a motor oil additive to provide suitable viscosity characteristics and to improve the environmental stress-cracking resistance of polyethylene. It has been incorporated in quantities of up to 30% in high-density polyethylene to improve the impact strength of heavy duty sacks. 

---