Hydrolysis concentrated-acid

The sequence of each different peptide or protein is important for understanding the activity of peptides and proteins and for enabling their independent synthesis, since the natural ones may be difficult to obtain in small quantities. To obtain the sequence, the numbers of each type of amino acid are determined by breaking down the protein into its individual amino acids using concentrated acid (hydrolysis). For example, hydrolysis of the tetrapeptide shown in Figure 45.3 would give one unit of glycine, two units of alanine, and one unit of phenylalanine. Of course, information as to which amino acid was linked to which others is lost. 

Eventually different technologies will be used for different feedstocks. The three approaches are concentrated acid hydrolysis, thermochemical and biological. A hybrid may also emerge. 

Chemical hycbolysis involves exposure of lignocellulosic materials to a chemical for a period of time at a >ecific temperature, and results in sugar monomers fiom cellulose and hemicellulose polymers. Acids are dominandy applied in chemical hydrolyses. Sulfuric acid is the most investigated acid (27), altoough other acids such as HCl (28) have also been used. Acid hydrolyses can be divided into two groups (a) concentrated-acid hydrolysis and (b) dilute-acid hydrolysis. 

Boil a mixture of 5 ml. (4 g.) of acetonitrile and 75 ml. of 10% aqueous sodium hydroxide solution in a 200 ml. flask under a refluxwater-condenser for 30 minutes, when hydrolysis will be complete. Detach the condenser and boil the solution in the open flask for a few minutes to drive off ull free ammonia. Then cool the solution, and add dilute sulphuric acid (i volume of concentrated acid 2 volumes of water)... 

Acidic Hydrolysis. Hot concentrated caustic alkalis first hydrolyse off the ethyl group, and then split the molecule to give one equivalent of acetic acid and one equivalent of the mono- or di-substituted acetic acid (as their alkali salts). 

Hydrolysis by acids. Place 15 ml. of starch solution in a boiling-tube, add I ml. of cone. HCl, mix well and place in a boiling water-bath for 20 minutes. Cool and add 2 drops of iodine solution to i ml. of the solution no blue coloration is produced. On the remainder, perform tests for glucose in particular show that glucosazone can be formed. Neutralise the excess of acid before carrying out these tests. (Note that a more concentrated acid is required to hydrolyse starch than to hydrolyse the disaccharides, such as sucrose.)... 

With concentrated alkali, fission occurs at the position adjacent to the carbonyl group to give acetic acid and a mono-substituted acetic acid the process is termed acid hydrolysis. 

Benzanilide and similar compounds are very slowly hydrolysed by concentrated hydrochloric acid hydrolysis is quite rapid with 60-70 per cent, sulphuric acid (for experimental details, see Section IV,52). In the preliminary experiment boil 0 5-1 Og. of the compound with 10-20 ml. of dilute sulphuric acid (1 1 by volume) imder reflux for 20-30 minutes. Dilute with 10ml.of water and filteroflfanyacid which may be precipitated if the carboxyhc acid is hquid and volatile, distil it directly from the reaction mixture. Render the residue alkaline and isolate the base as above. 

Molecular examples of trivalent molybdenum are known in mononuclear, dinuclear, and tetranuclear complexes, as illustrated in Figure 5. The hexachloride ion, MoCk (Fig- 5a) is generated by the electrolysis of Mo(VI) in concentrated HCl. Hydrolysis of MoCP in acid gives the hexaaquamolybdenum(III) ion, Mo(H20) g, which is obtainable in solution of poorly coordinating acids, such as triflic acid (17). Several molybdenum(III) organometaUic compounds are known. These contain a single cyclopentadienyl ligand (Cp) attached to Mo (Fig. 5d) (27). 

Niobic Acid. Niobic acid, Nb20 XH2O, includes all hydrated forms of niobium pentoxide, where the degree of hydration depends on the method of preparation, age, etc. It is a white insoluble precipitate formed by acid hydrolysis of niobates that are prepared by alkaH pyrosulfate, carbonate, or hydroxide fusion base hydrolysis of niobium fluoride solutions or aqueous hydrolysis of chlorides or bromides. When it is formed in the presence of tannin, a volurninous red complex forms. Freshly precipitated niobic acid usually is coUoidal and is peptized by water washing, thus it is difficult to free from traces of electrolyte. Its properties vary with age and reactivity is noticeably diminished on standing for even a few days. It is soluble in concentrated hydrochloric and sulfuric acids but is reprecipitated on dilution and boiling and can be complexed when it is freshly made with oxaHc or tartaric acid. It is soluble in hydrofluoric acid of any concentration. 

Acid Hydrolysis. With hot concentrated mineral acids, primary nitroparaffins yield a fatty acid and a hydroxylamine salt. If anhydrous acid and lower temperatures are used, the intermediate hydroxamic acid can be recovered. 

To produce the mtile titanium dioxide pigment, hydrolysis of the mother Hquor has to be carried out in the presence of a specially prepared hydrosol as a seeding agent. This hydrosol is made by the neutralization of a portion of the mother Hquor in the presence of hydrochloric or some other monohydric acid. Because of the large amount of the hydrosol that must be added to the mixture (about 6% concentration), the hydrolysis reaction takes only about 1 hr. 

The ratio of cycHc to linear oligomers, as well as the chain length of the linear sdoxanes, is controlled by the conditions of hydrolysis, such as the ratio of chlorosilane to water, temperature, contact time, and solvents (60,61). Commercially, hydrolysis of dim ethyl dichi oro sil a n e is performed by either batch or a continuous process (62). In the typical industrial operation, the dimethyl dichi orosilane is mixed with 22% a2eotropic aqueous hydrochloric acid in a continuous reactor. The mixture of hydrolysate and 32% concentrated acid is separated in a decanter. After separation, the anhydrous hydrogen chloride is converted to methyl chloride, which is then reused in the direct process. The hydrolysate is washed for removal of residual acid, neutralized, dried, and filtered (63). The typical yield of cycHc oligomers is between 35 and 50%. The mixture of cycHc oligomers consists mainly of tetramer and pentamer. Only a small amount of cycHc trimer is formed. 

In industrial production of acid-modified starches, a 40% slurry of normal com starch or waxy maize starch is acidified with hydrochloric or sulfuric acid at 25—55°C. Reaction time is controlled by measuring loss of viscosity and may vary from 6 to 24 hs. For product reproducibiUty, it is necessary to strictly control the type of starch, its concentration, the type of acid and its concentration, the temperature, and time of reaction. Viscosity is plotted versus time, and when the desired amount of thinning is attained the mixture is neutralized with soda ash or dilute sodium hydroxide. The acid-modified starch is then filtered and dried. If the starch is washed with a nonaqueous solvent (89), gelling time is reduced, but such drying is seldom used. Acid treatment may be used in conjunction with preparation of starch ethers (90), cationic starches, or cross-linked starches. Acid treatment of 34 different rice starches has been reported (91), as well as acidic hydrolysis of wheat and com starches followed by hydroxypropylation for the purpose of preparing thin-hoiling and nongelling adhesives (92). 

Aqueous sulfamic acid solutions are quite stable at room temperature. At higher temperatures, however, acidic solutions and the ammonium salt hydroly2e to sulfates. Rates increase rapidly with temperature elevation, lower pH, and increased concentrations. These hydrolysis reactions are exothermic. Concentrated solutions heated in closed containers or in vessels having adequate venting can generate sufficient internal pressure to cause container mpture. An ammonium sulfamate, 60 wt % aqueous solution exhibits mnaway hydrolysis when heated to 200°C at pH 5 or to 130°C at pH 2. The danger is minimised in a weU-vented container, however, because the 60 wt % solution boils at 107°C (8,10). Hydrolysis reactions are ... 

In the acid hydrolysis process (79—81), wood is treated with concentrated or dilute acid solution to produce a lignin-rich residue and a Hquor containing sugars, organic acids, furfural, and other chemicals. The process is adaptable to all species and all forms of wood waste. The Hquor can be concentrated to a molasses for animal feed (82), used as a substrate for fermentation to ethanol or yeast (82), or dehydrated to furfural and levulinic acid (83—86). Attempts have been made to obtain marketable products from the lignin residue (87) rather than using it as a fuel, but currently only carbohydrate-derived products appear practical. 

Derivatives like (491 R = Me) can be de-5-methylated by Raney nickel in ethanol or concentrated hydrochloric acid. Acid hydrolysis of (491 R = acyl) also affords 5-mercap-topyrazoles, whereas alkaline hydrolysis of the pyrazolium salt (495) furnishes methanethiol and antipyrine. 

Consistent with this, experiments using HS" labelled with radioactive (p. 661) show that acid hydrolysis of the 8203 produces elemental sulfur in which two-thirds of the activity is concentrated. Thiosulfates can also he made by boiling aqueous solutions of metal sulfites (or hydrogen sulfites) with elemental sulfur according to the stoichiometry... 

The acid hydrolysis of diaziridines has been investigated kinetic-ally. The reaction is first order and shows a relatively high temperature coefficient. Thus one finds a relatively high activation enthalpy (23-28 kcal) and a positive activation entropy (2-6 eu). The influence of substitution on nitrogen is small. The velocity of the diaziridine hydrolysis depends only in the weakly acid region on the acid concentration. Between pH 7 and 3 the fc-values rise by nearly 10 . For the... 

---