Color significance

Benzylindole colors significantly in contact with air at room temperature (ca. 1 week) but keeps indefinitely under argon. 

Color Significant figure Multiplier % Tolerance Capacitor Rating (V)... 

The presence of an AGN in M 81 can be inferred in two ways (1) nuclear colors significantly redder than the bulge, and (2) point source residual after... 

For an organic compound to absorb in the visible region (X > 400 nm), and hence to be colored, significant conjugation is necessary. The color observed is what is not absorbed. So if blue is absorbed. 

Qumones are colored p benzoqumone for example is yellow Many occur natu rally and have been used as dyes Alizarin is a red pigment extracted from the roots of the madder plant Its preparation from anthracene a coal tar derivative m 1868 was a significant step m the development of the synthetic dyestuff industry... 

Acetic acid, fp 16.635°C ((1), bp 117.87°C at 101.3 kPa (2), is a clear, colorless Hquid. Water is the chief impurity in acetic acid although other materials such as acetaldehyde, acetic anhydride, formic acid, biacetyl, methyl acetate, ethyl acetoacetate, iron, and mercury are also sometimes found. Water significantly lowers the freezing point of glacial acetic acid as do acetic anhydride and methyl acetate (3). The presence of acetaldehyde [75-07-0] or formic acid [64-18-6] is commonly revealed by permanganate tests biacetyl [431-03-8] and iron are indicated by color. Ethyl acetoacetate [141-97-9] may cause slight color in acetic acid and is often mistaken for formic acid because it reduces mercuric chloride to calomel. Traces of mercury provoke catastrophic corrosion of aluminum metal, often employed in shipping the acid. 

Nearly every chemical manufacturiag operation requites the use of separation processes to recover and purify the desired product. In most circumstances, the efficiency of the separation process has a significant impact on both the quality and the cost of the product (1). Liquid-phase adsorption has long been used for the removal of contaminants present at low concentrations in process streams. In most cases, the objective is to remove a specific feed component alternatively, the contaminants are not well defined, and the objective is the improvement of feed quality defined by color, taste, odor, and storage stability (2-5) (see Wastes, industrial Water, industrial watertreati nt). 

Tocotrienols differ from tocopherols by the presence of three isolated double bonds in the branched alkyl side chain. Oxidation of tocopherol leads to ring opening and the formation of tocoquinones that show an intense red color. This species is a significant contributor to color quaUty problems in oils that have been abused. Tocopherols function as natural antioxidants (qv). An important factor in their activity is their slow reaction rate with oxygen relative to combination with other free radicals (11). 

In general, textile fibers should be optically opaque so that their refractive indexes need to be significantly different from those of their most common environments, namely, air and water. Luster and color are two optical properties that relate to a fiber s aesthetic quatity and consumer acceptance. 

The predominant cellulose ester fiber is cellulose acetate, a partially acetylated cellulose, also called acetate or secondary acetate. It is widely used in textiles because of its attractive economics, bright color, styling versatiUty, and other favorable aesthetic properties. However, its largest commercial appHcation is as the fibrous material in cigarette filters, where its smoke removal properties and contribution to taste make it the standard for the cigarette industry. Cellulose triacetate fiber, also known as primary cellulose acetate, is an almost completely acetylated cellulose. Although it has fiber properties that are different, and in many ways better than cellulose acetate, it is of lower commercial significance primarily because of environmental considerations in fiber preparation. 

Hair products are normally cosmetics and are thus subject to aU. laws and regulations that control the labeling and claims of aU. cosmetic products. There are, however, several significant variations to this premise, ie, hair colorants, professional use only products, and products that make dmg claims. 

The various lubricants formulated into PVC to improve the processing can also enhance the performance of the stabilizet. In pigmented apphcations, calcium soaps, eg, calcium stearate, ate commonly used as internal lubricants to promote PVC fusion and reduce melt viscosity. This additive is also a powerfiil costabilizer for the alkyl tin mercaptide stabilizers at use levels of 0.2 to 0.7 phr. Calcium stearate can significantly improve the eady color and increase the long-term stabiUty at low levels however, as the concentration increases, significant yellowing begins to occur. 

---