Centrifuge, classification

A compressor is a machine that is used to increase the pressure of a gas or vapor. They can be grouped into two major classifications centrifugal and positive displacement. This section provides a general discussion of these types of compressors. 

Compressors can be divided into three classifications centrifugal, rotary, and reciprocating. This section identifies the common failure modes for each. 

Production and Shipment. Estimated adiponitrile production capacities in the U.S. in 1992 were about 625 thousand metric tons and worldwide capacity was in excess of lO metric tons. The DOT/IMO classification for adiponitrile is class 6.1 hazard, UN No. 2205. It requires a POISON label on all containers and is in packing group III. Approved materials of constmction for shipping, storage, and associated transportation equipment are carbon steel and type 316 stainless steel. Either centrifugal or positive displacement pumps may be used. Carbon dioxide or chemical-foam fire extinguishers should be used. There are no specifications for commercial adiponitrile. The typical composition is 99.5 wt % adiponitrile. Impurities that may be present depend on the method of manufacture, and thus, vary depending on the source. 

Particle Size Distribution. Almost every feed slurry is a mixture of fine and coarse particles. Performance depends on the frequency of distribution of particle size ia the feed. Figure 5 shows that whereas all of the coarse particles having a diameter greater than some are separated, fewer of the very fine particles are, at any given feed rate. The size distribution frequency of particles ia feed and centrate for a fine and coarse feed are quite different. More coarse particles separate out than fine ones. Classification of soHds by size is often done by centrifugal sedimentation. 

Glassification. Classification (2,12,26,28) or elutriation processes separate particles by the differences in how they settle in a Hquid or moving gas stream. Classification can be used to eliminate fine or coarse particles, or to produce a narrow particle size distribution powder. Classification by sedimentation iavolves particle settling in a Hquid for a predetermined time to achieve the desired particle size and size distribution or cut. Below - 10 fim, where interparticle forces can be significant, gravitational-induced separation becomes inefficient, and cyclone and centrifugation techniques must be used. Classification also separates particles by density and shape. Raw material separation by differential sedimentation is commonly used in mineral processiag. 

There are four (4) major types of pumps (I) positive displacement, (2) dynamic (kinetic), (3) lift, and (4) electromagnetic. Piston pumps are positive displacement pumps. The most common centrifugal pumps are of dynamic type ancient bucket-type pumps are lift pumps and electromagnetic pumps use electromagnetic force and are common in modern reactors. Canned pumps are also becoming popular in the petrochemical industiy because of the drive to minimize fugitive emissions. Figure 10-24 shows pump classification ... 

Solid-Bowl Centrifuge The Bird solid-bowl centrifuge uses powder instead of gravity and can develop centrifugal forces up to 1800 times the force of gravity. It is therefore a unique type in classification practice. 

Industrial Centrifugal Compressor Classification Based on Casing Design... 

The compressor or blower installation in a typical refinery or chemical process unit is not out-of-doors completely. Some form of shelter often is provided, ranging from only a roof to a completely closed building. When process equipment such as a centrifugal gas compressor, which is not hazardous in normal operation, is present in the shelter, the hazard classification depends on the extent to that which the shelter restricts ventilation. The extent of the shelter provided determines the area classification and the type of motor enclosure that should be applied. 

Two-phase suspension systems produce beaded products with broader particle-size distribution (e.g., 1-50 /rm). The microspherical particles usually need to be classified repeatedly to reduce the particle-size distribution in order to improve the resolution and efficiency in the separation for use in chromatography. The actual classification process depends on the size range involved, the nature of the beaded product, and its intended applications. Relatively large (>50 /rm) and mechanically stable particles can be sieved easily in the dry state, whereas small particles are processed more conveniently in the wet state. For very fine particles (<20 /rm), classification is accomplished by wet sedimentation, countflow setting, countflow centrifugation, or air classification. 

These operations may sometimes be better kno Ti as mist entrainment, decantation, dust collection, filtration, centrifugation, sedimentation, screening, classification, scrubbing, etc. They often involve handling relatively large quantities of one phase in order to collect or separate the other. Therefore the size of the equipment may become very large. For the sake of space and cost it is important that the equipment be specified and rated to Operate as efficiently as possible [9]. This subject will be limited here to the removal or separation of liquid or solid particles from a vapor or gas carrier stream (1. and 3. above) or separation of solid particles from a liquid (item 4j. Reference [56] is a helpful review. 

Classifications 477. Standard Units 481. General Calculations 481. Reciprocating Compressors 484. Rotarv Compressors 487. Centrifugal Compiessors 493. Axial-Flow Compressors 494. 

Another centrifugal pump classification is whether the pump is a single-stage pump (the pressure head is developed by a single impeller) or a multistage pump (the pressure head is developed by two or more impellers). 

There are two basic types of compressors (1) centrifugal and (2) positive displacement. Both of these major classifications can be further divided into sub-types, depending on their operating characteristics. This section provides an overview of the more common centrifugal and positive-displacement compressors. 

---