Osmium, catalyst

In a similar way, norbomene 2-ethylhexyl carboxylate, nor-bomene isobornyl carboxylate, norbomene phenoxyethyl carboxylate, (5) are and related monomers are obtained. As catalysts, osmium or ruthenium catalysts similar to those shown in Figure 1.8 are used. 

Zelinsky and Turowa-Pollak141 describe the specific properties of an osmium catalyst. Hydrogenation on osmium catalysts usually occurs at lower temperatures than on platinum, palladium, or nickel catalysts. Osmium asbestos is a very resistant catalyst that can be used for months on end without loss in activity disadvantages are that osmium catalysts that are not supported on carriers must be frequently regenerated and that when the temperature exceeds 150° osmium tends to decompose the material under hydrogenation. 

Oxidative rearrangements, via oxythallation, have been improved in yield and selectivity by the use of thallium(iii) nitrate supported on clay rather than in methanolic solution. Thus, cyclohexene gave an 85% yield of dimethoxymethyl-cyclopentane while 1-tetralone, which normally gives a complex mixture of products, gave a 1 1 mixture of methyl indane-l-carboxylate and 2-methoxytetralone. An efficient, large-scale procedure for the direct cis-dihydroxylation of olefins has been reported. The oxidant is t-butyl hydroperoxide and the catalyst osmium tetroxide, with the reaction conducted under alkaline conditions (E%N OH ), so facilitating a rapid turnover of catalyst via enhanced hydrolysis of the osmate esters. The method appears to be more advantageous for the more substituted olefins than the Hofmann and Miles procedure. 

Apart from the Fe catalyst, osmium and mthenium catalysts have been applied in ammonia synthesis reaction. The mthenium catalyst was found to be more active than the Fe catalyst, so it can perform at milder conditions than the Fe catalyst (Dahl et al., 2001 Logadottir et al., 2001 Rossetti, Pemicone, Ferrero, Fomi, 2006). However, Ru is more expensive than Fe, and the lifetime of the Ru catalyst is shorter than that of the Fe catalyst. 

Osmium(ll) Catalysts. Osmium-catalyzed cyclopropanation first appeared with osmium porphyrin as a catalyst (42). [Os(TTP)]2 catalyzed cyclopropanation of styrene with EDA and with good yield (79%) and high transselectivity tic = 10.2 1). No excess of stjrrene was required for this system. Later, from the experiment of cyclopropanation of styrene with diphenyldiazomethane, with [Os(TPFPP)] (TPFPP = meso-tetrakis(pentafiuorophenyl)porphyrinato dianion) as a catalyst, active intermediates were suggested to be a biscarbene rather than monocarbene species (43). Another osmium catalyst, [OsCl2(p-cymene)]2, has also been utilized as a catalyst for cyclopropanation of styrene derivatives with EDA at elevated temperature, with up to 85% yields (44). 

There is one other benzene to allylbenzene method that you should take a look at. Osmium sent in the article in which that magical clay and other similar catalyst add the allyl to aryl in record fashion. To read more check out ref 143. 

Figure 8.40 The k ySk) extended X-ray absorption fine structure (EXAFS) signal, Fourier transformed and then retransformed after application of the filter window indicated, in (a) osmium metal and (b) a 1% osmium catalyst supported on silica. (Reproduced, with permission, Ifom Winnick, FI. and Doniach, S. (Eds), Synchrotron Radiation Research, p. 413, Plenum, New York, 1980)...

With osmium tetroxide catalyst [PLATINUM-GROUP METALS, COMPOUNDS] (Vol 19)... 

CARBON - CARBON AND ARTIFICIALGRAPHITE - APPLICATIONS OF BAKED AND GRAPHITIZED CARBON] (Vol 4) -With osmium tetroxide catalyst [PLATINUM-GROUP METALS, COMPOUNDS] (Vol 19)... 

Oxidation. Maleic and fumaric acids are oxidized in aqueous solution by ozone [10028-15-6] (qv) (85). Products of the reaction include glyoxyhc acid [298-12-4], oxalic acid [144-62-7], and formic acid [64-18-6], Catalytic oxidation of aqueous maleic acid occurs with hydrogen peroxide [7722-84-1] in the presence of sodium tungstate(VI) [13472-45-2] (86) and sodium molybdate(VI) [7631-95-0] (87). Both catalyst systems avoid formation of tartaric acid [133-37-9] and produce i j -epoxysuccinic acid [16533-72-5] at pH values above 5. The reaction of maleic anhydride and hydrogen peroxide in an inert solvent (methylene chloride [75-09-2]) gives permaleic acid [4565-24-6], HOOC—CH=CH—CO H (88) which is useful in Baeyer-ViUiger reactions. Both maleate and fumarate [142-42-7] are hydroxylated to tartaric acid using an osmium tetroxide [20816-12-0]/io 2LX.e [15454-31 -6] catalyst system (89). 

The platinum-group metals (PGMs), which consist of six elements in Groups 8— 10 (VIII) of the Periodic Table, are often found collectively in nature. They are mthenium, Ru rhodium, Rh and palladium, Pd, atomic numbers 44 to 46, and osmium. Os indium, Ir and platinum, Pt, atomic numbers 76 to 78. Corresponding members of each triad have similar properties, eg, palladium and platinum are both ductile metals and form active catalysts. Rhodium and iridium are both characterized by resistance to oxidation and chemical attack (see Platinum-GROUP metals, compounds). 

Osmium may be used as a catalyst for the chemical and pharmaceutical industries. ... 

A Belgian patent (178) claims improved ethanol selectivity of over 62%, starting with methanol and synthesis gas and using a cobalt catalyst with a hahde promoter and a tertiary phosphine. At 195°C, and initial carbon monoxide pressure of 7.1 MPa (70 atm) and hydrogen pressure of 7.1 MPa, methanol conversions of 30% were indicated, but the selectivity for acetic acid and methyl acetate, usehil by-products from this reaction, was only 7%. Ruthenium and osmium catalysts (179,180) have also been employed for this reaction. The addition of a bicycHc trialkyl phosphine is claimed to increase methanol conversion from 24% to 89% (181). 

Rapoport s findings have been confirmed in the authors laboratory where the actions of carbon-supported catalysts (5% metal) derived from ruthenium, rhodium, palladium, osmium, iridium, and platinum, on pyridine, have been examined. At atmospheric pressure, at the boiling point of pyridine, and at a pyridine-to-catalyst ratio of 8 1, only palladium was active in bringing about the formation of 2,2 -bipyridine. It w as also found that different preparations of palladium-on-carbon varied widely in efficiency (yield 0.05-0.39 gm of 2,2 -bipyridine per gram of catalyst), but the factors responsible for this variation are not knowm. Palladium-on-alumina was found to be inferior to the carbon-supported preparations and gave only traces of bipyridine,... 

Rhodium-on-carbon has also been found to bring about the formation of 2,2 -biquinoline from quinoline, the yield and the percentage conversion being similar to that obtained with palladium-on-carbon. On the other hand, rhodium-on-carbon failed to produce 2,2 -bipyridine from pyridine, and it has not yet been tried with other bases. Experiments with carbon-supported catalysts prepared from ruthenium, osmium, iridium, and platinum have shown that none of these metals is capable of bringing about the formation of 2,2 -biquinoline from quinoline under the conditions used with palladium and rhodium. ... 

With this reaction, two new asymmetric centers can be generated in one step from an achiral precursor in moderate to good enantiomeric purity by using a chiral catalyst for oxidation. The Sharpless dihydroxylation has been developed from the earlier y -dihydroxylation of alkenes with osmium tetroxide, which usually led to a racemic mixture. 

The actual catalyst is a complex formed from osmium tetroxide and a chiral ligand, e.g. dihydroquinine (DHQ) 9, dihydroquinidine (DHQD), Zj -dihydroqui-nine-phthalazine 10 or the respective dihydroquinidine derivative. The expensive and toxic osmium tetroxide is employed in small amounts only, together with a less expensive co-oxidant, e.g. potassium hexacyanoferrate(lll), which is used in stoichiometric quantities. The chiral ligand is also required in small amounts only. For the bench chemist, the procedure for the asymmetric fihydroxylation has been simplified with commercially available mixtures of reagents, e.g. AD-mix-a or AD-mix-/3, ° containing the appropriate cinchona alkaloid derivative ... 

Osmium makes a sluggish carbonyl hydrogenation catalyst but has the unusual property of reducing a, -unsaturated aldehydes to the unsaturated alcohol in good yield (85). The system has proved erratic high selectivity can only be obtained through prereduction of the catalyst just before use. 

Reduction of unsaturated aldehydes seems more influenced by the catalyst than is that of unsaturated ketones, probably because of the less hindered nature of the aldehydic function. A variety of special catalysts, such as unsupported (96), or supported (SJ) platinum-iron-zinc, plalinum-nickel-iron (47), platinum-cobalt (90), nickel-cobalt-iron (42-44), osmium (<55), rhenium heptoxide (74), or iridium-on-carbon (49), have been developed for selective hydrogenation of the carbonyl group in unsaturated aldehydes. None of these catalysts appears to reduce an a,/3-unsaturated ketonic carbonyl selectively. 

Other examples are the use of osmium(VIII) oxide (osmium tetroxide) as catalyst in the titration of solutions of arsenic(III) oxide with cerium(IV) sulphate solution, and the use of molybdate(VI) ions to catalyse the formation of iodine by the reaction of iodide ions with hydrogen peroxide. Certain reactions of various organic compounds are catalysed by several naturally occurring proteins known as enzymes. 

Method A Standardisation with arsenic (III) oxide. Discussion. The most trustworthy method for standardising cerium(IV) sulphate solutions is with pure arsenic(III) oxide. The reaction between cerium(IV) sulphate solution and arsenic(III) oxide is very slow at the ambient temperature it is necessary to add a trace of osmium tetroxide as catalyst. The arsenic(III) oxide is dissolved in sodium hydroxide solution, the solution acidified with dilute sulphuric acid, and after adding 2 drops of an osmic acid solution prepared by dissolving 0.1 g osmium tetroxide in 40mL of 0.05M sulphuric acid, and the indicator (1-2 drops ferroin or 0.5 mL /V-phenylanthranilic acid), it is titrated with the cerium(IV) sulphate solution to the first sharp colour change orange-red to very pale blue or yellowish-green to purple respectively. 

Oscillometry 527 as analytical tool, 528 titrations (H.F.), 527 Osmium tetroxide catalyst 381 Ostwald s dilution law 31 Ovens electric, 97 microwave, 97 Overpotential 506 Overvoltage see Overpotential Oxalates, D. of as calcium carbonate via oxalate, (g) 484... 

Ruthenium nowadays finds many uses in the electronics industry, particularly for making resistor tracks. It is used as an ingredient in various catalysts and, importantly, in electrode materials, e.g. Ru02-coated titanium elements in the chloralkali industry. Osmium tetroxide is a very useful organic oxidant and, classically, is used as a tissue stain. Both elements are employed in making certain platinum alloys. 

The first catalytic study of Reaction 1 was published in 1902 by Sabatier and Senderens (1) who reported that nickel was an excellent catalyst. Since that time, the active catalysts were identified as the transition elements with unfilled 3d, 4d, and 5d orbitals iron, cobalt, nickel, ruthenium, rhenium, palladium, osmium, indium, and platinum, as well as some elements that can assume these configurations (e.g., silver). These are discussed later. For practical operation of this process,... 

Catalysts. The methanation of CO and C02 is catalyzed by metals of Group VIII, by molybdenum (Group VI), and by silver (Group I). These catalysts were identified by Fischer, Tropsch, and Dilthey (18) who studied the methanation properties of various metals at temperatures up to 800°C. They found that methanation activity varied with the metal as follows ruthenium > iridium > rhodium > nickel > cobalt > osmium > platinum > iron > molybdenum > palladium > silver. 

---